Patton electronics Model 1065 Manual de usuario

USER

MANUAL

MMOODDEELL

11006655

Industrial Synchronous &

Asynchronous Short

Range Modem

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

http://www.patton.com

Part# 07M1065-A

Doc# 058041UA

Revised 08/11/99

An ISO-9001

Certified

Company

1 2

1.0 WARRANTY INFORMATION

Patton Electronics warrants all Model 1065 components to be

free from defects, and will—at our option—repair or replace the prod-

uct should it fail within one year from the first date of shipment.

This warranty is limited to defects in workmanship or materials,

and does not cover customer damage, abuse or unauthorized modifi-

cation. If this product fails or does not perform as warranted, your sole

recourse shall be repair or replacement as described above. Under no

condition shall Patton Electronics be liable for any damages incurred

by the use of this product. These damages include, but are not limited

to, the following: lost profits, lost savings and incidental or consequen-

tial damages arising from the use of or inability to use this product.

Patton Electronics specifically disclaims all other warranties,

expressed or implied, and the installation or use of this product shall

be deemed an acceptance of these terms by the user.

1.1 RADIO AND TV INTERFERENCE

The Model 1065 generates and uses radio frequency energy, and

if not installed and used properly—that is, in strict accordance with the

manufacturer's instructions—may cause interference to radio and tele-

vision reception. If the Model 1065 does cause interference to radio or

television reception, which can be determined by disconnecting the

RS-232 interface, the user is encouraged to try to correct the interfer-

ence by one or more of the following measures: moving the comput-

ing equipment away from the receiver, re-orienting the receiving anten-

na and/or plugging the receiving equipment into a different AC outlet

(such that the computing equipment and receiver are on different

branches).

1.2 SERVICE

All warranty and non-warranty repairs must be returned freight

prepaid and insured to Patton Electronics. All returns must have a

Return Materials Authorization number on the outside of the shipping

container. This number may be obtained from Patton Electronics

Technical Service at:

tel: (301) 975-1007;

email: [email protected]; or,

www: http://www.patton.com.

NOTE: Packages received without an RMA number will not be

accepted.

Patton Electronics' technical staff is also available to answer any

questions that might arise concerning the installation or use of your

Model 1065. Technical Service hours: 8AM to 5PM EST, Monday

through Friday.

3 4

2.0 GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product.

This product has been thoroughly inspected by Patton's qualified tech-

nicians. If any questions or problems arise during installation or use of

this product, please do not hesitate to contact Patton Electronics

Technical Support at (301) 975-1007.

2.1 FEATURES

• Synchronous or asynchronous operation

• Model 1065 supports data rates up to 64.0 kbps

• Two-wire/half duplex or four-wire/full or half duplex

• V.52 & V.54 test modes

• Equalization

• Anti-streaming timer

• Distances up to 12 miles (19.2 km)

• Point-to-point or multipoint

• Internal, external or received loopback clocking

• 2000 VAC transformer isolation & high speed surge protection

• Internal power supply

• Mono-color LED indicators

2.2 DESCRIPTION

The Model 1065 Industrial Short Range Modem operates 2-wire

(half duplex) or 4-wire (full or half duplex), in synchronous or asyn-

chronous modes, over unconditioned telephone lines. The Model 1065

supports bit rates up to 64.0 kbps. The Model 1065 operates in syn-

chronous mode between the local and remote modems; when connect-

ed to an asynchronous RS-232 device, the Model 1065 SRM converts

the asynchronous data to synchronous data.

The Model 1065 has several features to enhance overall perform-

ance: equalization, anti-streaming timer, transformer isolation to guard

against data loss due to ground potential differences, and Silicon

Avalanche Diode surge protection to guard against data line transients.

The Model 1065 features V.52 compliant bit error rate pattern tests

and two V.54 test modes: local analog loopback and remote digital

loopback. The operator at the local end may test both local and

remote modems, plus the line, in the digital loopback mode. Both RDL

and LAL modes can be controlled by a manual switch or via the

V.24/RS-232 interface.

3.0 CONFIGURATION OVERVIEW

The Model 1065 is fairly simple to install and is ruggedly designed

for excellent reliability: just set it and forget it. The following instruc-

tions will help you set up and install the Model 1065 properly.

3.1 CONFIGURATION SWITCHES

The Model 1065 uses 24 external mini DIP switches that allow

configuration to an extremely wide range of applications. These 24

DIP switches are grouped into three eight-switch sets, and are exter-

nally accessible from the underside of the unit (see Figure 1). Since all

configuration DIP switches are externally accessible, there is no need

to open the case for configuration.

The configuration switches allow you to select data rates, clocking

methods, V.52 & V.54 tests, word lengths, extended signaling rates,

async. or sync. mode, 2- or 4-wire operation, anti-stream control and

input impedance. The drawings, text and tables on the following pages

describe all switch locations, positions and functions.

Figure 1. Bottom view of Model 1065 Series, showing location of DIP switches

FRONT

REAR

S1S2

OFF

5 6

The Model 1065 SRM has three sets of eight switches, yielding 24

total DIP switches. The three sets will be referred to as S1, S2 and

S3. As Figure 2 shows, the orientation of all DIP switches is the same

with respect to “ON” and “OFF” positions.

3.2 CONFIGURATION SWITCH SET “S1”

The DIP switches on S1 set data rate, clock source, async./sync.

mode and carrier control method. The default settings are summarized

in the table below.

Switches S1-1 through S1-4 & S3-3: Data Rate Setting

Switches S1-1, S1-4, and S3-3 are set in combination to deter-

mine the asynchronous and synchronous data rate for the Model 1065.

Shown in the tables below are DIP Switch settings for Models

1065.

* Must have switch 3-3 On

Switches S1-5 and S1-6: Clock Source

Switches S1-5 and S1-6 are set in combination to determine the

transmit clock source for the Model 1065 Series.

S1-5 S1-6 Setting

On On Internal transmit clock

Off On Receive recover clock

On Off External transmit clock

Switch S1-7: Asynchronous/Synchronous Mode

The setting for switch S1-7 determines whether the Model 1065

Series is in asynchronous or synchronous operating mode.

S1-7 Setting

On Asynchronous

Off Synchronous

Figure 2. Close-up of DIP switches showing “ON” and “OFF” positions

OFF

MODEL 1065 S1 SUMMARY TABLE

Position Function Factory Default

S1-1 Data Rate On

S1-2 Data Rate Off

S1-3 Data Rate Off

S1-4 Data Rate On

S1-5 Clock Source On

S1-6 Clock Source On

S1-7 Async./Sync. On Async.

S1-8 Carrier Control Off Constantly On

9,600 bps

Internal

}

S1-1 S1-2 S1-3 S1-4 S3-3 Setting

On On On On Off 1.2 kbps

Off On On On Off 1.8 kbps

On Off On On Off 2.4 kbps

Off Off On On Off 3.6 kbps

On On Off On Off 4.8 kbps

Off On Off On Off 7.2 kbps

On Off Off On Off 9.6 kbps

Off Off Off On Off 14.4 kbps

Off On Off On On 16.0 kbps

On On On Off Off 19.2 kbps

Off On On Off Off 28.8 kbps

Off Off Off On On 32.0 kbps

On On Off Off Off 38.4 kbps

Off On Off Off Off 57.6 kbps

Off On On Off On 64.0 kbps

MODEL 1065 DATA RATE SETTINGS

7 8

Switch S1-8: Carrier Control Method

The setting for switch S1-8 determines whether the carrier is “con-

stantly on” or “controlled by RTS”. This setting allows for operation in

switched carrier, multipoint and/or hardware handshaking applications.

S1-8 Setting

Off Constantly on

On Controlled by RTS

3.3 CONFIGURATION SWITCH SET “S2”

The DIP switches on S2 set word length, extended signaling rate,

RTS/CTS delay, V.52 and V.54 diagnostic test and 2- and 4-wire opera-

tion.

Switches S2-1 and S2-2: Word Length

Switches S2-1 and S2-2 are set in combination to determine the

word length for asynchronous data, including the start and stop bits.

S2-1 S2-2 Setting

Off On 8 bits

On On 9 bits

Off Off 10 bits

On Off 11 bits

Switch S2-3: Extended Signaling Rate

The setting for switch S2-3 determines the range of variability the

Model 1065 Series “looks for” in asynchronous data rates (i.e., the

actual variance from a given frequency level the Model 1065 Series will

tolerate).

S2-3 Setting

Off -2.5% to +1%

On -2.5% to +2.3%

Switches S2-4 and S2-5: RTS/CTS Delay

The combined settings for switches S2-4 and S2-5 determine the

amount of delay between the time the unit “sees” RTS and when it

sends CTS. Options are no delay, 7 ms and 53 ms.

S2-4 S2-5 Setting

On On 7 ms

Off On 53 ms

On Off No delay

Off Off No delay

Switch S2-6 & S2-7: 2-Wire/4-Wire Mode Selection

The setting for switch S2-6 and S2-7 determines whether the

Model 1065 Series is operating in 2-wire or 4-wire mode.

S2-6 S2-7 Setting

On On 4-wire (half duplex)

On Off 4-wire (full duplex)

Off On 2-wire (half duplex)

Switch S2-8: V.54 Loopback Test Enable

This switch enables or disables V.54 looping in the Model 1065.

S2-8 Setting

Off V.54 Normal Operation Enabled

On V.54 Testing Disabled

S2 SUMMARY TABLE

Position Function Factory Default

S2-1 Word Length Off

S2-2 Word Length Off

S2-3

Extended Signaling Rate

Off -2.5% to 1%

S2-4 RTS/CTS Delay On

S2-5 RTS/CTS Delay On

S2-6 2-Wire/4-Wire On (4-Wire) FDX

S2-7 2-Wire/4-Wire Off (4-Wire) FDX

S2-8 V.54 Off V.54 Enabled

}

7 ms

10 bits

9 10

3.4 CONFIGURATION SWITCH SET “S3”

The DIP switches on S3 set the anti-stream control, local loopback

enable, remote loopback enable and receive (input) impedance levels

for the Model 1065. Factory default positions of Switch S3 are shown

in the table below.

Switches S3-1 & S3-2: Input Impedance

The setting for Switches S3-1 and S3-2 determines the 1065

Series’ input impedance. This allows you to choose the optimum

impedance setting for your application. In long distance applications

the impedance of the cable must match the impedance of the load (or

resistor) of the Model 1065 Series unit. Thicker gauge cables requires

a lower Ohm setting, while a thinner gauge cable should receive a

higher Ohm setting. If you are using higher speeds you will need a

lower Ohm setting, and a higher Ohm setting for the slower speeds.

Refer to the table on the following page for assistance in selecting a

setting.

S3-1 S3-2 Setting

On On 130 Ohms

On Off 200 Ohms

Off On 320 Ohms

Off Off High impedance (minimum 2k ohms)

Switch S3-3: Rate Selection

Use Switch S3-3 to select the timing mode of the 1065. To oper-

ate the 1065 at 16, 32, or 64kbps, set S3-3 to the On position. To

select any other DTE rate, set Switch S3-3 Off.

S3-3 Setting

On 16, 32, or 64kbps

Off 1.2 - 57kbps, excluding 16 kbps and 32kbps

Switch S3-4: Topology

Use switch S3-4 to select the topology of the Model 1065.

S3-4 Setting

On Point to point

On Master multi-point

Off Slave multi-point

S3 SUMMARY TABLE

Position Function Factory Default

S3-1 Input Impedance On

S3-2 Input Impedance Off

S3-3 Timing Mode Off

S3-4 Topology On Point to Point

S3-5 Local Loopback Off Disabled

S3-6 Remote Loopback Off Disabled

S3-7 Anti-stream Control Off

S3-8 Anti-stream Control Off

200 Ohms

Disabled

}

S3-1, S3-2 SELECTION TABLE FOR MODEL 1065

Gauge of

Cable

19AWG/.9mm

22AWG/.6mm

24AWG/.5mm

26AWG/.4mm

1.2

320

Data Rates, kb/s

1.8

320

2.4

200

320

3.6

200

320

4.8

200

320

7.2

200

9.6

200

14.4

130

200

19.2

130

200

28.8

130

200

38.4

130

57.6

High

S3-1, S3-2 SELECTION TABLE FOR MODEL 1065 (CONTINUED)

Gauge of

Cable

19AWG/.9mm

22AWG/.6mm

24AWG/.5mm

26AWG/.4mm

130

200

Data Rates, kb/s

130

200

High

11 12

Switch S3-5: RS-232 Initiation of Local Loopback Test

The setting for switch S3-5 determines whether or not the Model

1065 local analog loopback test can be initiated by raising pin 18 on

the RS-232 interface.

S3-5 Setting

On RS-232 initiation enabled

Off RS-232 initiation disabled

Switch S3-6: RS-232 Initiation of Remote Loopback Test

The setting for switch S3-6 determines whether or not the Model

1065 remote digital loopback test can be initiated by raising pin 21 on

the RS-232 interface.

S3-6 Setting

On RS-232 initiation enabled

Off RS-232 initiation disabled

Switches S3-7 and S3-8: Anti-stream Control

Switches S3-7 and S3-8 are set in combination to determine the

time out period for the Model 1065 Series’ anti-stream control timer.

S3-7 S3-8 Setting

Off Off Disabled

Off On 12.5 seconds

On Off 50.0 seconds

On On 12.5 seconds

4.0 INSTALLATION

The Model 1065 operates in four twisted pair topologies:

2-wire/point-to-point, 2-wire/multipoint, 4-wire/point-to-point, and

4-wire/multipoint. In each of these topologies, the twisted pair wire

must be 19 - 26 AWG "dry", unconditioned metallic wire (see Appendix

C for wire recommendations). Dial-up analog circuits, such as those

used with a standard Hayes-type modem, are not acceptable. The

twisted pair may be shielded or unshielded. Both types yield favorable

results.

The Model 1065 offers an RJ-45 jack for its twisted pair line con-

nection. Figure 4 (below) shows the location of these interfaces on the

rear panel of the Model 1065 Series. Connect the wire to each Model

1065 Series as described in the instructions that follow the illustration.

The “+” and “-” indicators are for reference only.

4.1 TWO-WIRE INSTALLATION

When communicating over a single twisted pair circuit, the Model

1065 operates half duplex: that is, it transmits in only one direction at

a time. This method of operation is effective for both point-to-point and

multipoint applications.

In single pair point-to-point applications, you will need a pair of

Model 1065s for each circuit—one at each end of the single pair wire.

In single-pair multipoint applications you will need three or more Model

1065 units. These can be connected using a star topology, although a

daisy chain topology is usually used.

Figure 4. Model 1065 rear panel.

13 14

4.1.1 Two-Wire Cable Connection Via RJ-45

A. The RJ-45 jack on a Model 1065 Series Short Range Modem is

prewired for a standard TELCO wiring environment. To be sure you

have the right wiring, use the table below as a guide.

RJ-45 SIGNAL

1 -------------NC

2 -------------GND†

3 -------------RCV

4 -------------XMT

5 -------------XMT

6 -------------RCV

7 -------------GND

8 -------------NC

†Connection to ground is optional

B. Proper wiring of pairs between the two modems is as follows:

SIGNAL PIN# COLOR* COLOR PIN# SIGNAL

XMT 4 Green ------------Green 4 XMT

XMT 5 Red---------------Red 5 XMT

*Standard color codes—yours may be different

C. AT&T standard modular color codes:

4.2 FOUR-WIRE INSTALLATION

When communicating over a two twisted pair circuit, the Model

1065 can operate full or half duplex, point-to-point or multipoint. In two

pair point-to-point applications, you will need a

pair

of Model 1065s for

each circuit—one at

each end

of the two pair cable. In two pair multi-

point applications you will need three or more Model 1065 units. These

can be connected using a star topology, although a daisy chain topolo-

gy is usually used.

4.2.1 Four-Wire Cable Connection Via RJ-45

A. The RJ-45 jack on a Model 1065 Short Range Modem is

prewired for a standard TELCO wiring environment. To be sure you

have the right wiring, use the table below as a guide.

RJ-45 SIGNAL

1 -------------NC

2 -------------GND†

3 -------------RCV

4 -------------XMT

5 -------------XMT

6 -------------RCV

7 -------------GND

8 -------------NC

B. Proper crossing of pairs between the two modems is as fol-

lows:

†Connection to ground is optional

SIGNAL PIN# COLOR* COLOR PIN# SIGNAL

GND†2 Orange ----------Brown 7 GND

RCV 3 Black -------------Green 5 XMT

XMT 4 Red---------------Yellow 6 RCV

XMT 5 Green ------------Black 3 RCV

RCV 6 Yellow------------Red 4 XMT

GND 7 Brown------------Orange 2 GND

*Standard color codes—yours may be different

†Connection to ground is optional

1 - Blue

2 - Orange

3 - Black

4 - Red

5 - Green

6 - Yellow

7 - Brown

8 - Slate

15 16

C. AT&T standard modular color codes:

4.3 FOUR-WIRE, MULTIPOINT INSTALLATION

Multipoint operation involves the connection of several terminals to

one host port. In such an application, one local Model 1065 is used as

a master unit, and it is connected to several remote Model 1065s that

are acting as slaves.

In a multipoint environment the master Model 1065 transmits con-

tinually. Initiation of two-way communication is RTS controlled by each

“slave” Model 1065 unit. To facilitate multipoint communication, the

master Model 1065 should have its carrier control DIP switch set to

“constantly ON” (S1-8=OFF). Each slave Model 1065 unit should have

its carrier control DIP switch set to “controlled by RTS” (S1-8=ON).

Figure 5 illustrates a typical Model 1065 multipoint application.

4.3.1 Multipoint Twisted Pair Connection

The Model 1065 supports multipoint applications using a star topol-

ogy. Maximum distance between the units will vary based upon the

number of drops, data rate, wire gauge, etc. Call Patton Technical

Support for specific distance estimates. Figures 5 and 6 show how to

wire the one-pair and two-pair cables properly for a Model star topolo-

gy. Note that the ground connection is not needed.

HOST FIRST SLAVE SECOND SLAVE

XMT-----------------------------RCV

------------------------------------------------------------------RCV

XMT-----------------------------RCV

------------------------------------------------------------------RCV

RCV-----------------------------XMT

------------------------------------------------------------------XMT

RCV-----------------------------XMT

------------------------------------------------------------------XMT

HOST FIRST SLAVE SECOND SLAVE

XMT-----------------------------XMT

------------------------------------------------------------------XMT

RCV-----------------------------XMT

------------------------------------------------------------------XMT

4.4 RS-232 CONNECTION

Connect the synchronous or asynchronous output of your RS-232

device to the DB-25 interface on the rear panel of the Model 1065.

Note: The Model 1065 is wired to connect to a DTE. If your RS-232

output device is DCE, call Patton Technical Support at: (301) 975-

1007; http://www.patton.com; or, [email protected]

for specific installation instructions.

1 - Blue

2 - Orange

3 - Black

4 - Red

5 - Green

6 - Yellow

7 - Brown

8 - Slate

Figure 5. Typical multipoint set-up

17 18

5.0 OPERATION

Once you have configured each Model 1065 Series unit properly

and connected the twisted pair and RS-232 cables (see Section 4.0),

you are ready to operate the units. This section describes reading the

LED status monitors, powering-up and using the built-in V.52 and V.54

test modes.

5.1 LED STATUS MONITORS

The Model 1065 Series features seven front panel status LEDs that

indicate the condition of the modem and communication link. Figure 5

shows the front panel location of each LED. Following Figure 6 is a

description of each LED's function.

5.1.1 The “TD” and “RD” Indicators

The Power LED glows green to signal power present. The “TD” and

“RD” indicators blink green with data activity. Off indicates a low RS-

232 logic level, green indicates a high RS-232 logic level. Note: RS-

232 devices idle in a

low

state, so the LED will be off if the connections

are correct and the RS-232 device is in an idle state.

5.1.2 The “RTS” and “CD” Indicators

The “RTS” and “CD” indicators are monocolor and will be off for a

“low” signal or green for a “high” signal. RTS lights for an incoming

signal on RS-232 pin 4. CD lights for an incoming signal on the line

side, and the resulting output signal on RS-232 pin 8.

5.1.3 The “Test” Indicator

The yellow“Test” LED indicates that V.52 or V.54 tests are running.

5.1.4 The “Error” Indicators

The “Error” indicator LED has two functions:

A. When the 1065 unit is in test mode (green “Test” LED is lit), the

error LED glows red when bit errors occur.

B. When not in test mode (green “Test” LED is off), the error LED

is used to indicate an RTS streaming condition. (See Section 5.2) for

information on the anti-streaming circuitry.

5.2 ANTI-STREAMING ERROR INDICATOR

When not in test mode (green “Test” LED is off), the front panel

“Error” LED is used to indicate a streaming error. When the Model

1065s’ anti-streaming circuitry is enabled, the RTS signal from the DTE

is timer controlled. The timer begins to count when the DTE raises

RTS. If the time period that RTS remains high exceeds the preset time

out period, the anti-stream circuit will force RTS low. The “Error” LED

will light red, indicating a streaming condition (RTS continually on).

This feature prevents a malfunctioning terminal from tying-up a com-

puter port in a multi-drop or polling environment. When the DTE drops

RTS, the anti-streaming timer is automatically reset and the front panel

“Error” LED turns off. The time out period is DIP switch selectable for

12.5 or 50 seconds.

Figure 6. Model 1065 front panel.

Model 1065 Industrial Short Range Modem

TXPower RX RTS CD Error Test

V.54 Test

Modes

511 -

511E -

- Remote

- Normal

- Local

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Módem de Patton electronics

Patton electronics

Patton electronics 1058DVs Manual de usuario

Patton electronics

Patton electronics 1205P Manual de usuario

Patton electronics

Patton electronics 12168 Manual de usuario

Patton electronics

Patton electronics 1040 Manual de usuario

Patton electronics

Patton electronics RS-232 Manual de usuario

Patton electronics

Patton electronics 2192 Manual de usuario

Patton electronics

Patton electronics 1090 Manual de usuario

Patton electronics

Patton electronics 1082/F Manual de usuario

Patton electronics

Patton electronics 1093 Manual de usuario

Patton electronics

Patton electronics 1186 Manual de usuario

Patton electronics

Patton electronics 1060 Manual de usuario

Patton electronics

Patton electronics 1000 Manual de usuario

Patton electronics

Patton electronics NetLink 1082/144 Manual de usuario

Patton electronics

Patton electronics 1180/35 Manual de usuario

Patton electronics

Patton electronics 1007 Manual de usuario

Patton electronics

Patton electronics 1089/I Manual de usuario

Patton electronics

Patton electronics 1058 Manual de usuario

Patton electronics

Patton electronics 1010A Manual de usuario

Patton electronics

Patton electronics 1110 Manual de usuario

Patton electronics

Patton electronics 1080A Manual de usuario

Patton electronics

Patton electronics 1089/I Manual de usuario

Patton electronics

Patton electronics 1004 Manual de usuario

Patton electronics

Patton electronics 1193 Manual de usuario

Patton electronics

Patton electronics NetLink 1082/I Manual de usuario

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario