Paradox K32LCD+ Manual de usuario
Printed in Canada | 06/2014 K32LCD+ Quick Install Guide
Technical Specifications
Warranty
Warranty: For complete warranty information on this product, please refer to the
Limited Warranty Statement found on the Web site www.paradox.com/terms. Your
use of the Paradox product signifies your acceptance of all warranty terms and
conditions.
© 2014 Paradox Ltd. All rights reserved. Specifications may change without prior
notice. www.paradox.com
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
K32LCD+ Keypad
Quick Install Guide
The K32LCD+ keypad allows you to configure your Paradox
system through its interface.
Installation
1. Using a flathead screwdriver, pry the front housing assembly
from the backplate.
Figure 1: Opening the K32LCD+
Operating Voltage 9 to 16Vdc
Operating Temp. -10 to 55°C (14 to 131°F)
Power Consumption Maximum current - 150mA
Dimensions 15 x 12.6 x 2.7 cm (6 x 4.9 x 1.06 in.)
Weight 230g (8.1 oz)
Humidity 5-93%
Compatibility
Compatible with MG5000, MG5050, and Spectra
SP series V2.31 or higher and SP4000, SP65 V4.90
or higher.
Compliance EN50131-3 Grade 2; Environmental Class II
K32LCD+-EI00
K32LCD+ Quick Install Guide Printed in Canada | 06/2014
2. Mount the backplate to the wall by securing a M3.5 (#6)
screw in each of the dedicated mounting holes and tamper
hole. Ensure that the top is up, as shown in figure 2.
Figure 2: Backplate
3. Connect the 4-wire combus wires to the connector bus, as
shown in figure 3.
Figure 3: Wiring
4. Assemble both items by joining the hooks on the backplate
to their respected slots on the front housing assembly.
5. Secure the front housing to the backplate by snapping it
into place.
The installation process is now complete.
Configuration
To configure the modules through a keypad start by:
1. Press and hold the 0 (number zero) key.
NOTE:The area must be disarmed to configure it.
2. Initially you will see User Access Code but within 2 seconds
it will change to Installer Code.
3. When the Installer code appears, input the Installer code
number, the default number is [000000].
4. Input the 4 digit section code for Module Programming
[4003].
NOTE:You need module serial numbers for programming.
5. Input the Module serial number.
6. Input module sec [001].
7. Now you can start module programming.
Compatibility
The K32LCD+ is compatible with Magellan and Spectra series
control panels only. Please refer to the Technical Specifications
section for more details.
Wiring Slot
Wall Tamper
Top with hooks for
mounting keypad
panel
Mounting screw
holes
ZX1 is a:
Programmable
input
PGM is a:
Programmable
output
AllDisarmed
2014/19/0516:00
UserAccessCode
[*_]
InstallersCode
[_]
K32LCD+ Quick Install Guide Printed in Canada | 06/2014
2. Mount the backplate to the wall by securing a M3.5 (#6)
screw in each of the dedicated mounting holes and tamper
hole. Ensure that the top is up, as shown in figure 2.
Figure 2: Backplate
3. Connect the 4-wire combus wires to the connector bus, as
shown in figure 3.
Figure 3: Wiring
4. Assemble both items by joining the hooks on the backplate
to their respected slots on the front housing assembly.
5. Secure the front housing to the backplate by snapping it
into place.
The installation process is now complete.
Configuration
To configure the modules through a keypad start by:
1. Press and hold the 0 (number zero) key.
NOTE:The area must be disarmed to configure it.
2. Initially you will see User Access Code but within 2 seconds
it will change to Installer Code.
3. When the Installer code appears, input the Installer code
number, the default number is [000000].
4. Input the 4 digit section code for Module Programming
[4003].
NOTE:You need module serial numbers for programming.
5. Input the Module serial number.
6. Input module sec [001].
7. Now you can start module programming.
Compatibility
The K32LCD+ is compatible with Magellan and Spectra series
control panels only. Please refer to the Technical Specifications
section for more details.
Wiring Slot
Wall Tamper
Top with hooks for
mounting keypad
panel
Mounting screw
holes
ZX1 is a:
Programmable
input
PGM is a:
Programmable
output
AllDisarmed
2014/19/0516:00
UserAccessCode
[*_]
InstallersCode
[_]
Printed in Canada | 06/2014 K32LCD+ Quick Install Guide
Technical Specifications
Warranty
Warranty: For complete warranty information on this product, please refer to the
Limited Warranty Statement found on the Web site www.paradox.com/terms. Your
use of the Paradox product signifies your acceptance of all warranty terms and
conditions.
© 2014 Paradox Ltd. All rights reserved. Specifications may change without prior
notice. www.paradox.com
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
K32LCD+ Keypad
Quick Install Guide
The K32LCD+ keypad allows you to configure your Paradox
system through its interface.
Installation
1. Using a flathead screwdriver, pry the front housing assembly
from the backplate.
Figure 1: Opening the K32LCD+
Operating Voltage 9 to 16Vdc
Operating Temp. -10 to 55°C (14 to 131°F)
Power Consumption Maximum current - 150mA
Dimensions 15 x 12.6 x 2.7 cm (6 x 4.9 x 1.06 in.)
Weight 230g (8.1 oz)
Humidity 5-93%
Compatibility
Compatible with MG5000, MG5050, and Spectra
SP series V2.31 or higher and SP4000, SP65 V4.90
or higher.
Compliance EN50131-3 Grade 2; Environmental Class II
K32LCD+-EI00
Otros manuales para K32LCD+
3
Tabla de contenidos
Otros manuales de Teclado de Paradox
Paradox
Paradox Digiplex DGP2-641 Manual de usuario
Paradox
Paradox 1686V Manual de usuario
Paradox
Paradox 1640 Manual de usuario
Paradox
Paradox Digiplex DGP-641 Manual de usuario
Paradox
Paradox Digiplex DGP-620 Manual de usuario
Paradox
Paradox TM50 Touch Manual de usuario
Paradox
Paradox Esprit 636 Manual de usuario
Paradox
Paradox Esprit+ 642 Manual de usuario
Paradox
Paradox SP5500 Manual de usuario
Paradox
Paradox K32+ Manual de usuario
Paradox
Paradox K641+ Manual de usuario
Paradox
Paradox Esprit Manual de usuario
Paradox
Paradox Esprit 640 Manual de usuario
Paradox
Paradox Imperial Digiplex Evo R915 Manual de usuario
Paradox
Paradox Digiplex DGP-620 Instrucciones de funcionamiento
Paradox
Paradox Esprit+ 642 Manual de usuario
Paradox
Paradox Esprit+ 642 Manual de usuario
Paradox
Paradox Digiplex DGP2-648 Instrucciones de montaje
Paradox
Paradox Digiplex DGP-641 Manual de usuario
Paradox
Paradox Grafica DNE-K07 Instrucciones de funcionamiento
