Paradox Esprit 636 Manual de usuario

636 and 646 Keypads

User’s Manual

646

636

K6X6-EU12.fm Page -1 Tuesday, June 27, 2006 11:05 AM

K6X6-EU12.fm Page 0 Tuesday, June 27, 2006 11:05 AM

Table Of Contents

Basic Operation.............................. 2

Access Codes................................. 4

Arming & Disarming....................... 5

Panic Zones .................................. 11

Key Access Programming........... 12

Additional Features...................... 13

Trouble Display............................. 14

Fire Alarm Operation.................... 17

System Maintenance.................... 18

System Checklist.......................... 19

K6X6-EU12.fm Page 1 Tuesday, June 27, 2006 11:05 AM

2User’s Manual

1.0 Basic Operation

The Esprit 636 and 646 keypads both function in the

same way, but display the visual feedback differently.

1.1 Visual Feedback

The numbers, symbols, lights and keys on the keypad

communicate the status of your system as described

in Figure 1 on page 3.

1.2 Zones

The Esprit control panel can support up to 24 zones.

When a zone is opened, its corresponding key will

light up on the keypad. For example, if zone 5 were to

open, the [5] key will light up on the keypad. If the

zone is breached and an alarm occurs, the key will

flash until the system is disarmed. Esprit’s keypads

will show the status of the zones through keys [1] to

[12]. By default, keys [1] to [12] will display the status

of zones 1 to 12. Press the [2ND]key and keys [1] to

[12] will now display the status of zones 13 to 24

respectively.

1.3 Partitioning

Your Esprit system can be divided into two distinct

areas (System A and System B). User access codes

can arm or disarm one system or both systems

simultaneously. In partitioning mode, when System A

is armed, the [STAY]key flashes. If System B is

armed, the [AWAY]key flashes. If both systems are

armed, both of these keys will be flashing. If the

K6X6-EU12.fm Page 2 Tuesday, June 27, 2006 11:05 AM

Esprit Keypads 3

keypad is connected to a 738ULT, during an alarm,

the [STAY]and/or [AWAY]keys will stop flashing

Figure 1: Overview of the 636 & 646 Keypads

Green READY Light:

ON = All zones closed

OFF = Zone(s) open

Red ARMED Light:

ON = System Armed

Trouble Display

ON = Trouble(s) occurring

Alarm Memory Display

ON = Alarm(s) occurred

24-zone Display

Zone Keys (Keys 1 to 12):

ON = Zone open or breached

Flashing = System went into

alarm and breached zone will

flash

Orange AC Light (646 only):

ON = AC power is present

OFF = Power failure

C636

646

K6X6-EU12.fm Page 3 Tuesday, June 27, 2006 11:05 AM

4User’s Manual

2.0 Access Codes

2.1 Programming User Codes

In addition to the master code, the Esprit control panel

can be programmed to accept up to 48 user codes.

Note: Avoid programming simple or

obvious access codes, such as your

telephone number, address or codes such

as 1234.

To create or modify access codes, follow the steps

indicated in section 2.2. The Master Code and user

codes are identified by a 2 digit user number.

2.2 Creating User Codes

1. Press [ENTER]and then enter your Master Code

(default 474747) or User Code 1. You will hear a

confirmation beep and the [ENTER]key will flash.

2. Enter the two digit user number (01-48) for the

user code you wish to program (or 00 to change

the master code). You will hear a confirmation

beep and the [ENTER]key will stay on.

3. Key in 4 or 6-digit user access code and press

[ENTER]. The confirmation beep will sound again.

The [ENTER]key will flash. You may continue

programming other user codes, or press [CLEAR]

to exit programming mode.

Note: [2ND] key flashes if location is empty

(no code programmed).

K6X6-EU12.fm Page 4 Tuesday, June 27, 2006 11:05 AM

Esprit Keypads 5

2.3 Duress Codes

The last user code (User 48) can be programmed to

report a duress code. If you are forced to arm or

disarm your system under threat, a duress code can

be entered to produce a silent alarm at the monitoring

station. Check with your installer to see if this option

is active on your system.

2.4 Deleting a User Code

3.0 Arming & Disarming

3.1 Exit Delay

After entering a valid arming sequence, an exit delay

timer will provide you with time to exit the protected

area before the system arms. The keypad may beep

during the exit delay.

How do I delete a user code?

1. Press the [ENTER]key.

2. Enter your [MASTER CODE](default 474747).

3. Enter the 2-digit [USER NUMBER](01-48) to be deleted.

4. Press the [2ND]key.

5. Press the [ENTER]key.

6. If you wish to delete another user code, repeat steps 1

to 5. If you wish to exit, press the [CLEAR]key.

K6X6-EU12.fm Page 5 Tuesday, June 27, 2006 11:05 AM

6User’s Manual

3.2 Regular system arming

3.3 Stay Arming

Stay arming allows you to remain in the protected

area while partially arming the system (perimeter

zones only, such as doors and windows).

3.4 One Touch Arming

One touch system arming - no code required. Check

with your installer if these features are enabled.

3.4.1 Key [10] - Regular Arming:

When the READY light is on, pressing key [10] steadily

for 2 seconds automatically arms the system.

3.4.2 Key [STAY/11] - Stay arming:

Please refer to section 3.3 on page 6 for an explanation

of stay arming. Press the [STAY/11] key steadily for 2

How do I Regular arm the system?

1. The green READY light must be ON in order to arm the

system.

2. Enter your user code.

After the Confirmation beep, the READY light and the

[STAY]and [AWAY]keys will begin to flash. The exit

delay timer will begin the countdown to arming.

How do I Stay arm the system?

1. Press the [STAY]key.

2. Enter your User Code.

After the Confirmation beep, the READY light and the

[STAY]and [AWAY]keys will begin to flash. The exit

delay timer will begin the countdown to arming.

K6X6-EU12.fm Page 6 Tuesday, June 27, 2006 11:05 AM

Esprit Keypads 7

seconds. This will automatically Stay arm the system.

3.5 Double Stay Arming:

After Stay Arming and during the exit delay, press and

hold the [STAY/11] key to switch any delayed zones to

instant zones. Regular arming cancels double stay

arming.

3.6 Fast Exit While In Stay Mode:

3.6.1 Fast Exit and Stay Arm

To exit the already Stay armed premises and remain

Stay armed, press key [STAY/11] for two seconds. The

system will switch to exit delay mode (READY LED

flashes). At the end of the exit delay period, the

system will return to Stay arming mode.

3.6.2 Fast Exit and Regular Arm

To exit the already Stay armed premises and switch

to regular arming, press key [10] for two seconds.

The system will switch to Regular arming (keys [11]

and [12] flash) with an exit delay. At the end of the

exit delay period, the system is regular armed.

3.7 Keyswitch Arming

A keyswitch can be used to arm your system. If an

alarm is generated in your system, or a zone that has

not been defined as a Stay zone is opened after panel

arming, the system can only be disarmed from a

keypad (if keyswitch is defined as Stay arming).

K6X6-EU12.fm Page 7 Tuesday, June 27, 2006 11:05 AM

8User’s Manual

3.8 Manual Bypass Arming

This feature arms the system while bypassing zones

you wish to leave unarmed.

By using the Bypass Recall feature, you can reinstate

the latest zone bypass instructions saved in memory.

Press [BYP]in Step 2 (see above) and the previous

bypass status will be re-established.

3.9 Force/Away Arming

To arm the system rapidly without waiting for the

READY light (for all zones to close), use Force/Away

arming. Open zones will not be protected, but will be

armed as soon as they are closed.

3.10 Arming Both Systems Simultaneously

If your code has access to both systems:

How do I Manually Bypass Arm the system?

1. Press the [BYP]key and then enter your User Code.

The [BYP]key will illuminate as well as any zones that

have already been bypassed.

2. Enter the number of the zone(s) you wish to bypass.

To unbypass a bypassed zone, enter the zone number

of the bypassed zone.

3. Press [ENTER]. Arm the system using desired method.

The [BYP]key will remain illuminated to indicate that

there are bypassed zones.

How do I Force arm the system?

1. Press the [AWAY]key and then enter your user code.

The [AWAY]key will flash.

K6X6-EU12.fm Page 8 Tuesday, June 27, 2006 11:05 AM

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Teclado de Paradox

Paradox

Paradox TM50 Touch Manual de usuario

Paradox

Paradox Crimewatch TM50 Manual de usuario

Paradox

Paradox DigiplexNE DGP2-641 Manual de usuario

Paradox

Paradox Magellan MG32LRF Manual de servicio

Paradox

Paradox 1686V Manual de usuario

Paradox

Paradox Esprit+ 642 Manual de usuario

Paradox

Paradox DGP2-641 Guía del usuario

Paradox

Paradox Digiplex DGP2-648 Manual de usuario

Paradox

Paradox K32LCD+ Manual de usuario

Paradox

Paradox K70C Manual de usuario

Paradox

Paradox REM3 Manual de usuario

Paradox

Paradox Digiplex DGP-620 Instrucciones de funcionamiento

Paradox

Paradox Esprit Manual de usuario

Paradox

Paradox REM3 Manual de usuario

Paradox

Paradox K32+ Manual de usuario

Paradox

Paradox TM50 Touch Manual de usuario

Paradox

Paradox Grafica Manual de usuario

Paradox

Paradox Grafica DNE-K07 Instrucciones de funcionamiento

Paradox

Paradox Esprit 639 Manual de usuario

Paradox

Paradox Digiplex DGP2-648 Instrucciones de montaje

Paradox

Paradox Digiplex DGP-641 Manual de usuario

Paradox

Paradox Spectra 1689 Manual de usuario

Paradox

Paradox Spectra 1641 Instrucciones de montaje

Paradox

Paradox Paradox Digiplex DGP-610 Manual de usuario

Manuales populares de Teclado de otras marcas

BFT

BFT SELETTO Manual de usuario

Micro Id

Micro Id MP7G3BL Manual de instrucciones

WindowMaster

WindowMaster WLI 130 Manual de usuario

ACT

ACT ACT PRO 1030 Manual de usuario

Cardin

Cardin SSB Series Manual de usuario

Harman Kardon

Harman Kardon KP 1 Manual de usuario

Chamberlain

Chamberlain KPR2000 Guía del usuario

CYP

CYP CR-KP1 Manual de usuario

Aeware

Aeware k-35 Series Guía de referencia

Aritech

Aritech CS-175 Series Manual de usuario

GE NetworX NX-1600E Series Manual de usuario

Lenze AC Tech

Lenze AC Tech MC SERIES Manual de usuario

Burg Wächter

Burg Wächter secuENTRY 7711 Manual de usuario

Aeware

Aeware in.k450 Manual de usuario

Lenze

Lenze EPM-H410 Manual de usuario

Toshiba

Toshiba RKP007Z Manual de usuario

Gemini

Gemini GEM-DXK1 KEYPAD Manual de usuario

Russound

Russound MDK-C5 Manual de funcionamiento