Paradox Esprit 616 Manual de usuario
616, 626, 636 & 646
Keypads
User’s Manual
Esprit Keypads 1
TABLE OF CONTENTS
1.0 BASIC OPERATION ....................2
2.0 ACCESS CODES .........................4
3.0 ARMING & DISARMING ..............6
4.0 PANIC ZONES ..........................13
5.0 KEY ACCESS PROGRAMMING .14
6.0 ADDITIONAL FEATURES ..........15
7.0 TROUBLE DISPLAY ..................16
8.0 FIRE ALARM OPERATION ........18
9.0 SYSTEM MAINTENANCE ..........20
10.0 SYSTEM CHECKLIST .............21
2 User’s Manual
1.0 BASIC OPERATION
The Esprit 616, 626, 636 and 646 keypads all
function in the same way, but display the visual
feedback differently.
1.1 VISUALFEEDBACK
The numbers, symbols, lights and keys on the keypad
communicate the status of your system as described
below.
Figure 1: Overview of the 616 & 626 Keypads
Esprit Keypads 3
Figure 2: Overview of the 636 & 646 Keypads
4 User’s Manual
1.2 ZONES
The Esprit control panel can support up to 24 zones.
When a zone is opened or breached its
corresponding key will light up on the keypad. For
example, if zone 5 were to open, the 5 key will light up
on the keypad. The Esprit’s keypads will show the
status of the zones through keys 1 to 12. By default,
keys 1 to 12 will display the status of zones 1 to 12.
Press the [2ND]button and keys 1 to 12 will now
display the status of zones 13 to 24 respectively.
1.3 PARTITIONING
Your Esprit system is equipped with a partitioning
feature that can divide your alarm system into two
distinct areas (System A and System B). User access
codes can arm or disarm one system or both systems
simultaneously. In partitioning mode, when System A
is armed, the [STAY]key flashes. If System B is
armed, the [AWAY]key flashes. If both systems are
armed, both of these keys will be flashing.
2.0 ACCESS CODES
2.1 PROGRAMMINGUSERCODES
In addition to the master code, the Esprit control
panel can be programmed to accept up to 48 user
codes.
Esprit Keypads 5
Note: Avoid programming simple or
obvious access codes, such as your
telephone number, address or codes such
as 1234.
To create or modify access codes, follow the steps
indicated in section2.2. The master code and user
codes are identified by a 2 digit “code number”.
2.2 CREATINGUSERCODES
1) Press [ENTER]and then enter your master code
(default 474747) or user 1 code. You will hear
the “confirmation” beep and the [ENTER]key will
flash.
2) Enter the two digit “code number” (01-48) for the
user code you wish to program (or 00 to change
the master code). You will hear the
“confirmation” beep and the [ENTER]key will stay
on.
3) Key in 4 or 6-digit user access code and press
[ENTER]. The “confirmation” beep will be heard
again. The [ENTER]key will flash. You may
continue programming other user codes, or
press [CLEAR]to exit programming mode.
Note: [2ND]key flashes if location is empty
(no code programmed).
6 User’s Manual
2.3 DURESS CODES
The last user code (user 48) can be programmed to
report a “duress code”. If you are forced to arm or
disarm your system under threat, a duress code can
be entered to produce a silent alarm at the monitoring
station. Check with your installer to see if this option
is active on your system.
2.4 DELETINGAUSERCODE
3.0 ARMING & DISARMING
3.1 EXITDELAY
After entering a valid arming sequence, an exit delay
timer will provide you with time to exit the protected
area before the system arms. The keypad may beep
during the exit delay.
How do I delete a user code?
1) Press the [ENTER]key.
2) Enter your [MASTERCODE](default 474747).
3) Enter the 2-digit [CODENUMBER](01-48) to be deleted.
4) Press the [2ND]key.
5) Press the [ENTER]key.
6) If you wish to delete another user code, repeat steps 1
to 5. If you wish to exit, press the [CLEAR]key.
Esprit Keypads 7
3.2 REGULAR SYSTEMARMING
3.3 STAYARMING
Stay arming allows you to remain in the protected
area while “partially” arming the system (perimeter
zones only, such as doors and windows).
3.4 ONETOUCH ARMING
One touch system arming - no code required. Check
with your installer if these features are enabled.
3.4.1 Key [10] - Regular Arming:
When the “ready” light is on, pressing key [10]
steadily for 2 seconds automatically arms the system.
How do I Regular Arm the system?
1) The green “READY’light must be ON in order to arm
the system.
2) Enter your User Code.
After the Confirmation beep, the “ready” light and the
[STAY]and [AWAY]buttons will begin to flash. The exit
delay timer will begin the countdown to arming.
How do I Stay Arm the system?
1) Press the [STAY]button.
2) Enter your User Code.
After the Confirmation beep, the “ready” light and the
[STAY]and [AWAY]buttons will begin to flash. The exit
delay timer will begin the countdown to arming.
8 User’s Manual
3.4.2 Key [STAY/11] - Stay arming:
Please refer to section3.3 on page7 for an
explanation of stay arming. Press the [STAY/11] key
steadily for 2 seconds. This will automatically “Stay”
arm the system.
3.5 DOUBLESTAYARMING:
After Stay Arming and during the exit delay, press
and hold the [STAY/11] key to switch any delayed
zones to “instant” zones. Regular arming cancels
“double stay” arming.
3.6 FASTEXITWHILEINSTAYMODE:
3.6.1 Fast Exit and Stay Arm
To exit the already Stay armed premises and remain
Stay armed, press key [STAY/11] for two seconds.
The system will switch to exit delay mode (“ready”
LED flashes). At the end of the exit delay period, the
system will return to “Stay” arming mode.
3.6.2 Fast Exit and Regular Arm
To exit the already Stay armed premises and switch
to regular arming, press key [10] for two seconds.
The system will switch to regular arming (keys [11]
and [12] flash) with an exit delay. At the end of the
exit delay period, the system is regular armed.
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Teclado de Paradox
Paradox
Paradox SP5500 Manual de usuario
Paradox
Paradox Digiplex DGP-620 Instrucciones de montaje
Paradox
Paradox Esprit 639 Manual de usuario
Paradox
Paradox Digiplex DGP2-648 Manual de usuario
Paradox
Paradox TM40 Manual de usuario
Paradox
Paradox Digiplex DGP-620 Manual de usuario
Paradox
Paradox Esprit+ 642 Manual de usuario
Paradox
Paradox IMPERIAL V32 Manual de usuario
Paradox
Paradox Grafica Manual de usuario
Paradox
Paradox Magellan K636 Manual de usuario
Paradox
Paradox Paradox Digiplex DGP-610 Manual de usuario
Paradox
Paradox K32LCD+ Manual de usuario
Paradox
Paradox 1640 Manual de usuario
Paradox
Paradox TM50 Touch Manual de usuario
Paradox
Paradox K70C Manual de usuario
Paradox
Paradox REM3 Manual de usuario
Paradox
Paradox Digiplex DGP2-641 Manual de usuario
Paradox
Paradox Spectra 1641BL Manual de usuario
Paradox
Paradox K32LCD Guía de solución de problemas
Paradox
Paradox 1686V Manual de usuario
