Panasonic Transistors 2SC4691J Manual de usuario
Transistors
1
Publication date: January 2003 SJC00282BED
2SC4691J
Silicon NPN epitaxial planar type
For high-speed switching
■Features
•Low collector-emitter saturation voltage VCE(sat)
•SS-Mini type package, allowing downsizing of the equipment and
automatic insertion through the tape packing
■Absolute Maximum Ratings Ta=25°C
Parameter Symbol Conditions Min Typ Max Unit
Collector-base cutoff current (Emitter open)
ICBO VCB =40 V, IE=0 0.1 µA
Emitter-base cutoff current (Collector open)
IEBO VEB =4 V, IC=0 0.1 µA
Forward current transfer ratio *hFE VCE =1 V, IC=10 mA 60 200
Collector-emitter saturation voltage VCE(sat) IC=10 mA, IB=1 mA 0.17 0.25 V
Base-emitter saturation voltage VBE(sat) IC=10 mA, IB=1 mA 1.0 V
Transition frequency fTVCB =10 V, IE=−10 mA, f =200 MHz 450 MHz
Collector output capacitance Cob VCB =10 V, IE=0, f =1 MHz 2 6 pF
(Common base, input open circuited)
Turn-on time ton Refer to the measurement circuit 17 ns
Turn-off time toff 17 ns
Storage time tstg 10 ns
■Electrical Characteristics Ta=25°C ±3°C
Unit: mm
Parameter Symbol Rating Unit
Collector-base voltage (Emitter open) VCBO 40 V
Collector-emitter voltage (E-B short) VCES 40 V
Emitter-base voltage (Collector open) VEBO 5V
Collector current IC100 mA
Peak collector current ICP 300 mA
Collector power dissipation PC125 mW
Junction temperature Tj125 °C
Storage temperature Tstg −55 to +125 °C
Marking Symbol: 2Y
Note) 1. Measuring methods are based on JAPANESE INDUSTRIAL STANDARD JIS C 7030 measuring methods for transistors.
2. *: Rank classification
Rank Q R No-rank
hFE 60 to 120 90 to 200 60 to 200
Product of no-rank is not classified and have no indication for rank.
0.27
±0.02
3
12
0.12
+0.03
–0.01
0.80
±0.05
(0.80)
0.85
1.60
±0.05
0 to 0.02
0.10 max.
0.70
+0.05
–0.03
(0.375)
5˚
5˚
1.60
+0.05
–0.03
1.00
±0.05
(0.50)(0.50)
+0.05
–0.03
1: Base
2: Emitter
3: Collector
EIAJ: SC-89
SSMini3-F1 Package
This product complies with the RoHS Directive (EU 2002/95/EC).
2SC4691J
2SJC00282BED
VBE(sat) IChFE ICCob VCB
PCTaICVCE VCE(sat) IC
220 Ω
0.1 µF
50 Ω
V
CC
= 3 V
V
OUT
3.3 kΩ
50 Ω
V
IN
= 10 V
3.3 kΩ
VBB = −3 V
V
IN
V
OUT
t
on
90%
10%
90%
10%
t
off
(Waveform at A)
V
IN
V
OUT
10%
10%
t
stg
910 Ω
0.1 µF
0.1 µF
A
90 Ω
V
CC
= 10 V
V
OUT
500 Ω
50 Ω
V
IN
= 10 V
500 Ω
1 kΩ
V
BB
= 2 V
t
on
, t
off
test circuit t
stg
test circuit
Measurement circuit
0 15012510025 7550
0
150
125
100
75
50
25
Ambient temperature T
a
(°C)
Collector power dissipation P
C
(mW)
0654132
0
250
200
150
100
50
T
a
= 25°C
I
B
= 8 mA
7 mA
6 mA
5 mA
4 mA
3 mA
2 mA
1 mA
Collector-emitter voltage V
CE
(V)
Collector current I
C
(mA)
0.1 1 10 100 1
000
0.01
1
0.1
IC / IB= 10
Ta= 75°C
25°C
−25°C
Collector current I
C
(mA)
Collector-emitter saturation voltage V
CE(sat)
(V)
0.1 1 10 100
0.1
10
1
I
C
/ I
B
= 10
T
a
= 75°C
25°C
−25°C
Base-emitter saturation voltage V
BE(sat)
(V)
Collector current I
C
(mA)
0.1 1 10 100 1
000
0
160
120
40
100
140
80
20
60
V
CE
= 1 V
T
a
= 75°C
25°C
−25°C
Forward current transfer ratio hFE
Collector current IC(mA)
0 5 15 20 25 3010 35
0.1
100
10
1
f = 1 MHz
T
a
= 25°C
Collector-base voltage VCB (V)
Collector output capacitance
(Common base, input open circuited) C
ob
(pF)
This product complies with the RoHS Directive (EU 2002/95/EC).
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1)If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2)The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other
company which may arise as a result of the use of technical information described in this book.
(3)The products described in this book are intended to be used for standard applications or general electronic equipment (such as office
equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
–Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-
ucts may directly jeopardize life or harm the human body.
–Any applications other than the standard applications intended.
(4)The products and product specifications described in this book are subject to change without notice for modification and/or im-
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5)When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6)Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7)This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita
Electric Industrial Co., Ltd.
Otros manuales de Hardware de red de Panasonic
Panasonic
Panasonic PIN Photodiodes PNZ334 (PN334) Manual de usuario
Panasonic
Panasonic Schottky Barrier Diodes MA3Z792DG Manual de usuario
Panasonic
Panasonic Schottky Barrier Diodes MA6J786Y Manual de usuario
Panasonic
Panasonic Schottky Barrier Diodes MA27E02 Manual de usuario
Panasonic
Panasonic Transistors 2SA2161J Manual de usuario
Panasonic
Panasonic Switching Diodes MA6X128 (MA128) Manual de usuario
Panasonic
Panasonic Schottky Barrier Diodes MA3X727 (MA727) Manual de usuario
Panasonic
Panasonic SH-ALL1C Manual de usuario
Panasonic
Panasonic i-pro WJ-NT304 Manual de usuario
Panasonic
Panasonic Schottky Barrier Diodes MA2Z720 Manual de usuario
Panasonic
Panasonic AJ-DE77P Manual de usuario
Panasonic
Panasonic LJ-SK56A Manual de usuario
Panasonic
Panasonic Zener Diodes MAZSxxx Series Manual de usuario
Panasonic
Panasonic PIN Diodes MA27P07 Manual de usuario
Panasonic
Panasonic PN261693D Manual de usuario
Panasonic
Panasonic Fast Recovery Diodes MA2DF60 Manual de usuario
Panasonic
Panasonic Transistors 2SC5846 Manual de usuario
Panasonic
Panasonic Transistors 2SD1823 Manual de usuario
Panasonic
Panasonic Rectifier Diodes MA2J115 (MA115) Manual de usuario
Panasonic
Panasonic WJ-NX200K Manual de usuario
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
