Oneida Air Systems BenchTop DC Manual de usuario

BenchTop DC™

Personal Dust Collector

#XBZ000100

Rev: 08/19/2020 Doc. #ZBM000041

Appearance may vary slightly

OWNER’S MANUAL

oneida-air.com 1

Table of Contents

System Start-Up Information 2

System Specications and Dimensions 3

System Contents 4

Assembly Instructions 6

Features 9

Maintenance 10

Troubleshooting 12

F.A.Q. 13

Recommended Accessories 14

Warranty Information 16

Notes 17

Oneida Air Systems, Inc.2

System Start-Up Information

1. THIS UNIT IS NOT RATED FOR USE IN COMBUSTIBLE ENVIRONMENTS.

2. is equipment incorporates parts such as switches, motors or the like that tend to produce arcs or sparks that can cause an

explosion.

3. To reduce the risk of Electric Shock, DO NOT use outdoors or on wet surfaces.

4. Exhaust air should not be vented into a wall, a ceiling, or a concealed space of a building.

5. To reduce the risk of injury from moving parts - unplug BEFORE servicing.

6. Use this equipment for dry material collection only. DO NOT use for liquid or gas vapor collection.

 WARNING 

 FIRE HAZARDS 

1. Wood shaping and cutting processes generate wood chips, shavings and dust. ese materials are considered combustible. Air

borne wood dust below 420 microns in size (0.017 of an inch) in certain concentration ranges when ignited can deagrate (burn

quickly). An ignition source such as a spark or ember can ignite a dust mixture resulting in an expanding ame front, which can

cause an explosion if tightly contained. A disturbance that raises a cloud of accumulated ne dust can raise additional dust clouds,

which can cause a series of explosions that can level an entire building. Until this type of re has been witnessed, it is dicult to

believe the devastation. is type of re is rare but worth safeguarding against.

2. e best way to avoid a wood shop re is to keep the shop clean. A shop ankle deep in dust with layers of ne dust everywhere

is an accident waiting to happen. A good dust collection system reduces overall re hazards but also adds new concerns. A re

hazard is still present. Combustible material is now in the dust collector and storage container.

3. DO NOT use this product to collect ammable dust or ammable vapors! - Fire or explosion may occur!

4. NEVER collect sparks from a bench grinder into a wood dust collector.

5. NEVER introduce sparks or sources of ignition into the dust collector.

6. Keep portable re extinguishers handy.

a. e ABC type (dry chemical) is generally a good choice for small wood shops.

b. Additional information on portable extinguishers can be found in NFPA 10 (Standard for Portable Fire Extinguishers).

7. DO NOT overload woodworking equipment, especially sanders. Excessive frictional heat can spontaneously ignite dust.

8. Sparks can be generated in several ways:

a. High speed sanders and abrasive planers may strike foreign material.

b. Saws and edgers may strike foreign material and create a red-hot metal fragment.

c. Knots in hardwood can create frictional sparks.

d. Check wood stock for old nails and screws which can create red hot metal fragments.

9. DO NOT allow accumulation of layers of ne dust on horizontal surfaces (especially overhead lights, electrical boxes and fuse

panels which can ignite dust.)

10. UNPLUG UNIT BEFORE SERVICING OR CLEANING

MAKE SURE TO READ AND UNDERSTAND THE INSTALLATION AND MAINTENANCE INSTRUCTIONS AS

WELL AS ALL RECOMMENDED SAFETY PRACTICES.

25-1/2" W 9-3/4" D

16-1/2" H

oneida-air.com 3

System Specications and Dimensions

OPERATION

Airow 535 CFM

Horsepower 0.3HP

Phase Single-Phase

Voltage 110V

Cycle 60HZ

Amperage Draw 3A

On/O Switch Analog Variable Speed Control

Power Cord Length 6'

Plug Type NEMA 5-15P

Noise Level 62.5 to 74 dBA

SYSTEM DIMENSIONS AND CONSTRUCTION

Primary Build Materials Cold Rolled Steel with a powder-coated nish

Overall Weight 20 lbs

Pre-Filter Dimensions 16 x 24-1/4 x 1/2"

Main Filter Dimensions 16 x 25 x 3"

Outer Filtration / Material MERV 5 / Polyester

Main Filter Filtration / Material MERV 15 / Synthetic

Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.

Oneida Air Systems, Inc.4

System Contents

Please unpack the parts carefully and conrm you have received each item listed here.

*Components are pre-installed at the factory and are listed here for maintenance and convenience. e pre-installed

components will be referred to as the BenchTop DC Assembly (A).

ID Part number Part description Qty

A XBZ000100 BenchTop DC Assembly 1

B* BTB000100 Fan Assembly 1

C* FCS000001 Main Filter 1

D* FCS162503 Pre-Filter 1

E* RBB000100 Frame Assembly 1

F BTV000001 Left Vane 1

ID Part number Part description Qty

G BTV000003 Top Vane 1

H BTV000002 Right Vane 1

I RGC062524 24" Cork Strip 1

J RGC012515 1-1/2" Cork Strip 2

K WCW000007 AC Cord 1

If you cannot find an item on the list, examine the packaging materials very carefully for nested items. Please

note that certain components have been pre-installed. There may be hardware leftover.

oneida-air.com 5

System Contents (Continued)

J K

Oneida Air Systems, Inc.6

Assembly Instructions

FIG. 1a

FIG. 1b

FIG. 1c

FIG. 2

1 Install the Cork Strips (I, J) to the BenchTop

DC Assembly (A):

a. Turn the BenchTop DC Assembly (A)

upside down [FIG. 1a]. Clean and dry the

bottom thoroughly.

b. Align the 24" Cork Strip (I) along the front

edge of the BenchTop DC Assembly as

shown in [FIG. 1b]. Peel the backer tape o

and adhere to the BenchTop DC Assembly

(A)

c. Align the 1-1/2" Cork Strips (J) along the

le and right edge of the BenchTop DC

Assembly as shown in [FIG. 1C]. Peel the

backer tape o and adhere both pieces to

the BenchTop DC Assembly (A). Turn the

unit right-side up.

Note: Press each piece rmly onto the bracket to

ensure a long-lasting seal.

2 Insert the Top Vane (G) between the Frame

Assembly (E) and Pre-Filter (D) as shown

in [FIG. 2]. e Top Vane will be held in

place by the Pre-Filter pressing on it until the

remaining Vanes are installed.

FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE

IS COMPLETELY ASSEMBLED. PLEASE ALSO MAKE SURE THAT YOU READ AND UNDERSTAND THE ENTIRE

INSTRUCTION MANUAL.

oneida-air.com 7

Assembly Instructions (Continued)

FIG. 3a

FIG. 3b

FIG. 3c

3 Install the Le and Right Vanes (F, H) to the

BenchTop DC Assembly (A):

a. Locate the lower notches on the front of

the Frame Assembly. [FIG. 3a]

b. Slide the Right Vane (H) between the

Frame Assembly (E) and Pre-Filter (D) at

an angle so that it slips under the Top Vane

(G) and settles into the lower right notch

as shown in [FIG. 3b].

c. Rotate the Right Vane (H) so that it is

vertical and perpendicular to the Top Vane

(G). Align and insert the two tabs of the

Right Vane (H) into the two corresponding

slots of the Top Vane (G). Press down

rmly so that both components clip into

position [FIG. 3c].

d. Mirror Steps a-c for the Le Vane (F) on

the other side of the Frame Assembly.

Note: Make certain the two tabs on both the Le

and Right Vane are seated securely in the slots of

the Top Vane.

RESET

OFF

RESET

OFF

RESET

OFF

Oneida Air Systems, Inc.8

Assembly Instructions (Continued)

FIG. 4

FIG. 6

FIG. 5a FIG. 5b

4 Plug the female end of the AC Cord (K) into

the BenchTop DC Assembly (A) male port.

Make certain that the power switch is in the

o position and then plug the AC Cord into an

AC power source (wall outlet) [FIG. 4].

Note: We recommended that you work close

to the front of the unit to ensure the best dust

collection possible. is unit is not meant to

replace other source collection devices, such

as built in dust ports or bags. It is meant to

supplement those tools and create a cleaner zone

of air around the user.

5 Press the switch to the RESET position [FIG.

5a]. e fan speed can be adjusted as needed

using the knob below the switch [FIG. 5b].

6 Tools can be plugged into the accessory port

and should not exceed 10 amps [FIG. 6].

Note: Tools plugged into the accessory port will

remain powered on even when the BenchTop

DC's power switch is in the OFF position.

THIS MACHINE MUST HAVE A GROUND PRONG IN THE PLUG TO HELP ENSURE THAT IT IS GROUNDED. DO

NOT REMOVE GROUND PRONG FROM PLUG TO FIT INTO A TWOPRONGED OUTLET! IF THE PLUG WILL

NOT FIT THE OUTLET, HAVE THE PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.

OFF

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Colector de polvo de Oneida Air Systems

Oneida Air Systems

Oneida Air Systems Dust Cobra Manual de usuario

Oneida Air Systems

Oneida Air Systems Supercell Mobile Manual de usuario

Oneida Air Systems

Oneida Air Systems XXK100300 Manual de usuario

Oneida Air Systems

Oneida Air Systems Pro 1500 Manual de usuario

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Manual de usuario

Oneida Air Systems

Oneida Air Systems Mini-Gorilla Manual de usuario

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD002030 Manual de usuario

Oneida Air Systems

Oneida Air Systems Deluxe Dust Deputy Manual de usuario

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Manual de usuario

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Manual de usuario

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD990003 Manual de usuario

Oneida Air Systems

Oneida Air Systems XXVM001500 Manual de usuario

Oneida Air Systems

Oneida Air Systems Gorilla XXP999901 Manual de usuario

Oneida Air Systems

Oneida Air Systems BenchTop Manual de usuario

Oneida Air Systems

Oneida Air Systems V-System XXVS300035 Manual de usuario

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Manual de usuario

Oneida Air Systems

Oneida Air Systems Smart Dust Collector Manual de usuario

Oneida Air Systems

Oneida Air Systems Supercell Mobile Manual de usuario

Oneida Air Systems

Oneida Air Systems XCKM010000 Manual de usuario

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla 2hp Manual de usuario

Oneida Air Systems

Oneida Air Systems 5HP High Pressure Dust Collector Manual de usuario

Oneida Air Systems

Oneida Air Systems 2 HP Commercial Cyclonic Dust Collector Manual de usuario

Oneida Air Systems

Oneida Air Systems Supercell XSK000035 Manual de usuario

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Manual de usuario

Manuales populares de Colector de polvo de otras marcas

Fein

Fein 9-88-35 Manual de usuario

Blastrac

Blastrac BDC-44 Manual de usuario

DIVERSITECH

DIVERSITECH WB-4000-D Manual

National

National 3402 Manual de usuario

Grizzly

Grizzly G0850 Manual de usuario

Bosch

Bosch GDE18V-16 Instrucciones de montaje

Grizzly

Grizzly G0441HEP Manual de usuario

Storch

Storch Cover Quick Wall Manual de usuario

laguna

laguna C FLUX 1 Manual de usuario

Jet

Jet DC-1100VX Series Manual de servicio

GMC

GMC RDC8LA Manual de usuario

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Manual de usuario

King Industrial

King Industrial KC-4043KWRC Manual de usuario

Jet

Jet 500 Manual de usuario

Shop fox

Shop fox SHOP FOX W1687 Manual de usuario

Blastrac

Blastrac 655DC Manual de usuario

Elektra Beckum

Elektra Beckum Multi 180A Manual de usuario

Grizzly

Grizzly G0508 Guía de inicio rápido