Oneida Air Systems V-System XXVS300035 Manual de usuario

Rev: B 20221019LL Doc. #ZBM000046

Appearance may vary slightly

US Pat. 8496719, 8377160,

8514090, 9370740, D908854,

7247180, 8491685

OWNER’S MANUAL

V-System®

with SMART Boost®

3HP

# XXVS300035

# XXVS300055

# XXVS300035W

# XXVS300055W

1oneida-air.com

Table of Contents

System Start-Up Information 2

System Specications 4

Stand and Leg Extension Dimensions 5

System Dimensions for 35 Gallon Drum 6

System Dimensions for 55 Gallon Drum 7

System Contents 8

Assembly Instructions 10

Maintenance 21

Troubleshooting 22

F.A.Q. 23

Recommended Accessories 25

Warranty Information 27

Notes 28

Oneida Air Systems, Inc.2

System Start-Up Information

1. Install ductwork/ex hose completely before operating collector.

a. Seal ductwork with silicone sealant or duct tape if leaks are found.

b. Have dust drum in place and sealed.

2. THIS UNIT IS NOT RATED FOR USE IN COMBUSTIBLE ENVIRONMENTS.

3. is equipment incorporates parts such as switches, motors or the like that tend to produce arcs or sparks that can cause an

explosion.

4. Operating without the lter can blow debris around and cause injury.

5. To reduce the risk of Electric Shock, DO NOT use on wet surfaces and have adequate protection outdoors. It is the buyer’s

responsibility to follow all applicable federal, state, local, OSHA, NFPA, or authorities having jurisdiction codes and

regulations when installing and operating this dust collector.

6. Exhaust air should not be vented into a wall, a ceiling, or a concealed space of a building.

7. To reduce the risk of injury from moving parts - unplug BEFORE servicing.

8. Ensure that your dust collector is turned o and unplugged during installation.

9. Use this equipment for dry material collection only. DO NOT use for liquid collection.

 WARNING 

 FIRE HAZARDS 

1. Wood shaping and cutting processes generate wood chips, shavings and dust. ese materials are considered combustible.

Airborne wood dust below 420 microns in size (0.017 of an inch) in certain concentration ranges when ignited can

deagrate (burn quickly). An ignition source such as a spark or ember can ignite a dust mixture resulting in an expanding

ame front, which can cause an explosion if tightly contained. A disturbance that raises a cloud of accumulated ne dust can

raise additional dust clouds, which can cause a series of explosions that can level an entire building. Until this type of re has

been witnessed, it is dicult to believe the devastation. is type of re is rare but worth safeguarding against.

2. e best way to avoid a wood shop re is to keep the shop clean. A shop ankle deep in dust with layers of ne dust

everywhere is an accident waiting to happen. A good dust collection system reduces overall re hazards but also adds new

concerns. A re hazard is still present. Combustible material is now in the dust collector and storage container.

3. e following points are worth heeding:

a. It is the buyer’s responsibility to follow all applicable federal, state, local, OSHA, NFPA, or authorities having jurisdiction

codes and regulations when installing and operating this dust collector.

b. Fire Marshals may want the unit located outside of the building. If the collector is located inside the facility, controls

such as spark detection, suppression, or explosion venting may be required.

c. Most local jurisdictions consult or adopt NFPA (National Fire Protection Agency) codes. However, other codes may

apply. Local codes may vary from jurisdiction to jurisdiction.

d. NFPA664 Code book, “Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking

Facilities”, applies to woodworking operations that occupy areas of more than 5,000 sq. . or to areas where dust

producing equipment requires an aggregate dust collection ow rate of more than 1,500 cfm (cubic feet per minute).

MAKE SURE TO READ AND UNDERSTAND THE INSTALLATION AND MAINTENANCE

INSTRUCTIONS AS WELL AS ALL RECOMMENDED SAFETY PRACTICES.

oneida-air.com 3

System Start-Up Information (Continued)

is exempts some small operators from the NFPA code 664, but other codes may apply in your jurisdiction. Consult

your local Fire Marshal for help. Additional information can be found in NFPA Code Book 664.

4. e customer assumes the responsibility for contacting their insurance underwriter regarding specic application

requirements of explosion venting or if additional re protection and safety equipment may be required.

5. DO NOT use this product to collect ammable dust or ammable vapors! - Fire or explosion may occur!

6. NEVER collect sparks from a bench grinder into a wood dust collector.

7. NEVER introduce sparks or sources of ignition into the dust collector.

8. Check dust bin frequently for smoldering material and before leaving the shop.

9. Keep portable re extinguishers handy.

a. e ABC type (dry chemical) is generally a good choice for small wood shops.

b. Additional information on portable extinguishers can be found in NFPA 10 (Standard for Portable Fire Extinguishers).

10. Be especially careful with sanding units. ey can produce concentrations of dust in the combustible range. Make certain

enough air volume is at the suction point to capture all the particulate generated.

11. is high air volume will dilute the mixture below the lower limit of ammability. Be careful not to generate sparks into the

sanding dust.

12. Empty dust bin and clean lter oen, especially when sanding.

13. DO NOT overload woodworking equipment, especially sanders. Excessive frictional heat can spontaneously ignite dust.

14. Sparks can be generated in several ways:

a. High speed sanders and abrasive planers may strike foreign material.

b. Saws and edgers may strike foreign material and create a red-hot metal fragment.

c. Knots in hardwood can create frictional sparks.

d. Trapped metal when drawn into the collector can spark against ductwork.

e. Wood stock for old nails and screws which can create red hot metal fragments.

15. Avoid using excessively large wood waste bins.

16. ALWAYS check storage bins for smoldering material before leaving for the day.

17. Electrically ground all equipment and ducting. Static sparks can ignite wood dust. (Avoid using PVC drain pipe.)

18. DO NOT allow accumulation of layers of ne dust on horizontal surfaces (especially overhead lights, electrical boxes and

fuse panels which can ignite dust).

19. UNPLUG UNIT BEFORE SERVICING OR CLEANING.

Customer Service Dept.

1-866-387-8822 • support@oneida-air.com

4Oneida Air Systems

System Specications

OPERATION

Fan Rating (Free Fan) 2,940 CFM

Fan Rating (with Cyclone & Filter) 1,030 CFM at 2"W.C.

Maximum Suction Rating 21" WC

MOTOR AND ELECTRICAL

Motor Type U.S. Made TEFC Motor

Motor Insulation Class F

Motor Service Factor 1.15

Horsepower 3 HP

Motor Speed 3,500-4,500 RPM

Phase Single-Phase (1ph)

Voltage 208-230V

Cycle 60Hz

Listed FLA 15-17.5A

On/O Switch Remote Starter with Push button On/O Switch and RF Keyfob

Power Cord 7 ft

Power Connector Wire

Recommended Circuit Size 30A

Recommended Circuit Size HACR

Sound Emission 77 dBA at 10 ft

IMPELLER

Size 15"

Material Single-piece, backward inclined, non-sparking/non-ferrous

CARTRIDGE FILTER

Filter Media Type HEPA Grade ePTFE Media

Filter Eciency E12 Minimum Eciency Rating

Filter Surface Area 95 sq. ft.

SYSTEM DIMENSIONS AND CONSTRUCTION

Barrel/Cyclone Body Heavy-gauge cold-rolled steel

Inlet 6" Diameter

Overall Height (with 35 Gallon Drum) 84"

Overall Height (with 55 Gallon Drum) 96"

5oneida-air.com

54-3/16"

1,376 mm

Stand and Leg Extension Dimensions

Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.

 The Angle Bracket Leg Extension Kit (#STZ212301) is included with the 55 gallon drum kits. The

Leg Extensions are required for the 35 gallon drum kits if you purchased the Universal Drum Dolly

(#SDD990000) or the 13" Stacking Sound Filter (#BSS131400).

33"

838 mm

30-1/4"

769 mm

30-1/4"

769 mm

Position 1

Position 2

Position 3

Position 1

58-3/16"

1,478 mm

For 35 gallon drum

and Universal

Drum Dolly

For 55 gallon drum

and/or Stacking

Sound Filter

For 55 gallon drum,

Universal Drum Dolly,

and/or Stacking

Sound Filter

Position 2

66-3/16"

1,681 mm

Position 3

70-11/16"

1,796 mm

6Oneida Air Systems

83-7/8"

2,130 mm

65-1/2"

1,666 mm

27"

686 mm

30"

762 mm

7-1/2"

191 mm

6-1/8"

157 mm

36"

914 mm

54-1/4"

1,379 mm

58-1/4"

1,481 mm

25-1/2"

646 mm

Nominal dimensions shown with a 35 gallon drum. Dimensions subject to slight variations in manufacturing.

Top View

System Dimensions for 35 Gallon Drum

16"

406 mm

49"

1,243 mm

30"

764 mm

33"

838 mm

7oneida-air.com

95-7/8"

2,435 mm

16"

406 mm

49"

1,243 mm

77-1/2"

1,971 mm

30"

764 mm

33"

838 mm

6-1/8"

157 mm

36"

914 mm

66-1/4"

1,684 mm

70-1/4"

1,786 mm

37-3/8"

950 mm

19-1/2"

496 mm

27"

686 mm

30”

762 mm

Nominal dimensions shown with a 55 gallon drum. Dimensions subject to slight variations in manufacturing.

Top View

System Dimensions for 55 Gallon Drum

16"

406 mm

49"

1,243 mm

30"

764 mm

33"

838 mm

8Oneida Air Systems

Please unpack the parts carefully and conrm you have

received each item listed here.

* Additional Hardware included

†Additional parts are included in your hardware

package (AHX000005).

‡Combined inside hardware package (AHX000516).

ID Part number Part description Qty

A BXI030118C Motor Assembly 3 HP 1 PH 1

B BHX020005B Fan Housing 1

C SXB300055 Cone 1

D ACB120000 12" Clamp Band 2

E DHF090001 9" Diameter Flex Hose 1

F SEX550900 Steel Drum Lid w/ 9" Collar 1

GSES350000

SES550000

35 Gallon Steel Drum w/ Clamp

55 Gallon Steel Drum w/ Clamp 1

H FCS133695HF 13" x 36" HEPA Cartridge Filter 1

I GXF010013 13" Plenum Kit 1

I1 FPX000001 Filter Plenum Elbow 1

I2 FPX010013 13" Filter Plate 1

I3 BSC130000 Drop-in Silencer 1

I4 FPZ000013 Fine Dust Bin 1

I5 AHX001318 Plenum Hardware Kit 1

I5A AFJ051602 5/16-18" x 2" J-Bolt 8

I5B AFT000001 5/16-18" Thumb Nut 8

I5C AFB516125 5/16-18" x 1.25" Bolt 9

I5D AFW180000 5/16" Flat Washer 9

I5E AFT155175 5/16-18" Whiz-Lock Nut 9

J AHX000003C V-System Hardware Kit 1

J1 RGZ000000 Neoprene Foam Gasket Roll 25'

ID Part number Part description Qty

J2 RGZ125075* Gasket Roll 6'

J3 AFB155155† 5/16"-18 x 1" Flange Bolt 46

J4 AFT155175† 5/16" Whiz-Lock Nut 46

J5 AFT900516‡ 5/16"-18 Nylock Nut 8

J6 AFW180000‡ 5/16" Flat Washer 8

J7 FGA000002 14" Grounding Cable w/Two 8-18 x

3/8" Self-tapping Screws 1

J8 AFW180000† 5/16" Flat Washer 8

K FPB120001 Plenum Support Brace 1

L STZ180001 Stand Assembly 1

M AMR240000 Remote 1

N AXB999110B Dust Sentry 1

INCLUDED ONLY WITH 55-GALLON STEEL DRUM

O STZ212301 Leg Extension Assembly 1

INCLUDED ONLY WITH WALL BRACKET SYSTEMS

P SMS300021A Wall Bracket 1

System Contents

You will need the following tools:

GENERAL FAN HOUSING FILTER

8' Ladder Razor Knife Flathead Screwdriver 7/16" Wrench

Level Diagonal Cutters Hammer 7/16" Socket Wrench

Scissors Tape Measure / Ruler

1/2" Wrench 1/4" Socket

1/2" Socket Wrench Impact Driver

If you cannot find an item on the list, examine the packaging materials very carefully.

Certain components have been pre-installed. *There may be hardware leftover.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Colector de polvo de Oneida Air Systems

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Manual de usuario

Oneida Air Systems

Oneida Air Systems XGK030035 Manual de usuario

Oneida Air Systems

Oneida Air Systems 10 HP Manual de usuario

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Manual de usuario

Oneida Air Systems

Oneida Air Systems BenchTop Manual de usuario

Oneida Air Systems

Oneida Air Systems V-1500 1.5hp Manual de usuario

Oneida Air Systems

Oneida Air Systems Supercell XSK000030 Manual de usuario

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Manual de usuario

Oneida Air Systems

Oneida Air Systems Supercell Mobile Manual de usuario

Oneida Air Systems

Oneida Air Systems Smart Dust Collector Manual de usuario

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Manual de usuario

Oneida Air Systems

Oneida Air Systems Deluxe Dust Deputy Manual de usuario

Oneida Air Systems

Oneida Air Systems Deluxe Dust Deputy Manual de usuario

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Manual de usuario

Oneida Air Systems

Oneida Air Systems Mini-Gorilla Manual de usuario

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Manual de usuario

Oneida Air Systems

Oneida Air Systems V1500 Manual de usuario

Oneida Air Systems

Oneida Air Systems Smart Pro XXS200001 Manual de usuario

Oneida Air Systems

Oneida Air Systems Supercell Mobile Manual de usuario

Oneida Air Systems

Oneida Air Systems Supercell XSK000014 Manual de usuario

Oneida Air Systems

Oneida Air Systems 5 & 7.5 HP Direct Drive Cyclonic Dust... Manual de usuario

Oneida Air Systems

Oneida Air Systems Supercell XSK000035 Manual de usuario

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Manual de usuario

Oneida Air Systems

Oneida Air Systems XCKM013000 Manual de usuario

Manuales populares de Colector de polvo de otras marcas

Fein

Fein 9-88-35 Manual de usuario

Blastrac

Blastrac BDC-44 Manual de usuario

DIVERSITECH

DIVERSITECH WB-4000-D Manual

National

National 3402 Manual de usuario

Grizzly

Grizzly G0850 Manual de usuario

Bosch

Bosch GDE18V-16 Instrucciones de montaje

Grizzly

Grizzly G0441HEP Manual de usuario

Storch

Storch Cover Quick Wall Manual de usuario

laguna

laguna C FLUX 1 Manual de usuario

Jet

Jet DC-1100VX Series Manual de servicio

GMC

GMC RDC8LA Manual de usuario

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Manual de usuario

King Industrial

King Industrial KC-4043KWRC Manual de usuario

Jet

Jet 500 Manual de usuario

Shop fox

Shop fox SHOP FOX W1687 Manual de usuario

Blastrac

Blastrac 655DC Manual de usuario

Elektra Beckum

Elektra Beckum Multi 180A Manual de usuario

Grizzly

Grizzly G0508 Guía de inicio rápido