Olympus SZ2-STU1 Manual de usuario

INSTRUCTIONS

AX6623

This instruction manual is for the Olympus Stands for stereo microscopes. To ensure the safety,

obtain optimum performance and to familiarize yourself fully with the use of this equipment, we

recommend that you study this manual thoroughly before operating the system.

Retain this instruction manual in an easily accessible place near the work desk for future reference.

UNIVERSAL STAND TYPE 1

UNIVERSAL STAND TYPE 2

TABLE CLAMP STAND

SZ2-STU1/SZ2-STU2

SZ2-STU3

SZ2 series

CONTENTS

IMPORTANT – Be sure to read this section for safe use of the equipment. – 1-2

1 MODULES, EXTERNAL VIEW AND DIMENSIONS 3

2 NOMENCLATURE AND ASSEMBLY 4

3 OPERATION 5-6

SZ2-STU1/SZ2-STU3

IMPORTANT – Be sure to read this section for safe use of the equipment. – 7

1 MODULES, EXTERNAL VIEW AND DIMENSIONS 8

2 NOMENCLATURE AND ASSEMBLY 9-10

3 OPERATION 11- 13

SZ2-STU2

This device complies with the requirements of directive 98/79/EC concerning in vitro diagnostic

medical devices. CE marking means the conformity to the directive.

}Intended use

This instrument has been designed to be used to observe magnified images of specimens in routine and research

applications.

Do not use this instrument for any purpose other than its intended use.

The SZ2-STU1, SZ2-STU2 and SZ2-STU3 stands are provided with ESD (Electro-Static Discharge) protection specifica-

tions. Each stand is provided with electroconductive coating in their external finish to reduce the surface resistance.

Connecting a grounding lead wire to the stand (and also the horizontal arm in case of the SZ2-STU2) makes it possible

eliminate static electricity quickly.

CAUTION To maintain the ESD protection performance, always use the stand in combination with a stereo

microscope, arm used with microscope for equipment mounting and options having the ESD

protection specifications. Otherwise, the grounding will not work properly.

· The clamping knob of the stand is not provided with the ESD protection performance. (The

clamping knob with the ESD protection performance is available on custom order.)

· With the SZ2-STU2, circuit continuity between the horizontal arm and base plate is interrupted by

the friction surface of the column. These parts should be grounded individually.

CAUTION After the equipment has been used in an observation of a specimen that is accompanied with a

potential of infection, clean the parts coming in contact with the specimen to prevent infection.

Fig. 1

Load

Front

Side Rear

Side

SZ2-STU1/SZ2-STU3

IMPORTANT

1. Install the stand on a level desktop (inclination angle of less than 3°).

2. When moving the stand, make sure that the clamping mechanisms are

secured tightly and lift the stand by holding it by the base plate. If the

stand is held by the horizontal arm or column alone, the base plate may

drop.

3. The load of the stand is limited (see table below). A heavy object such as

a photography unit cannot be used.

The column is attached at a position deviated from the center of the

base plate.

The safety of the stand varies depending on the orientation of the hori-

zontal arm. (Figs. 1 & 2)

When the horizontal arm is extended at maximum, the load to the bonder

arm is limited as shown in the following table.

Front 70° Max. 4.6 kg

Side 85° Max. 3.0 kg

Rear 120° Max. 2.0 kg

The horizontal arm is most stable when it is oriented in the front 70°

range shown in Fig. 2.

4. When a wide space is required in front of the microscope, the horizontal

arm should often be oriented in the rear 120° range and the stand tends

to topple down easily. In this case, fix the stand firmly by using a table

clamp @ or placying a weight (3 kg or more) ² on the base plate. (Fig. 3)

SAFETY PRECAUTIONS

SZ2-STU1

Fig. 2

Fig. 3

*Under this condition, the stand tends

to topple down easily if another load

is applied during the microscope op-

eration. It is recommended to set the

horizontal arm as short as possible.

Top view

SZ2-STU1/STU3

Fig. 4

40 mm or more

10 - 60 mm

1. Install the stand on a sturdy table ³ having thickness of 10 to 60 mm

and edge space length of 40 mm or more. (Fig. 4)

2. The load capacity is 4.6 kg regardless of the orientation.

3. Before installing or uninstalling the stand on or from the table, remove the

column from the table clamp to secure safety.

If you do not remove the column, always have another person hold the

horizontal arm section.

4. If internal oscillations are troublesome, insert the provided rubber sheet

| below the stand. (Fig. 4)

³|

SZ2-STU3

SZ2-STU1/SZ2-STU3

MODULES, EXTERNAL VIEW AND DIMENSIONS (Unit: mm)

Universal Stand Type 1

SZ2-STU1

Bonder Arm

SZ2-STB1

· Base plate weight: 17.5 kg

· Total weight: 25.4 kg

(including the 0.9 kg bonder arm)

Table Clamp Stand

SZ2-STU3

(The shaded parts are identical to the

SZ2-STU1.)

· Clamp section weight: 2 kg

· Total weight: 9.9 kg

(including the 0.9 kg bonder arm)

Mountable Modules

}To maintain the ESD protection performance, the following modules should also be provided with the ESD protection

performance.

· Microscope body: SZ2 series, SZX7, SZ series or SD/SF series

· Oblique illumination system: LSGA (mountable on the SZ2-STB1)

· Other modules mounted on the microscope body

CAUTION From the viewpoint of safety, it is prohibited to mount the photography unit on the stand.

SZ2-STU1/STU3

Fig. 5

Fig. 6

Allen wrench

storage position

Operation mistake

prevention ring

Clamping screws

NOMENCLATURE AND ASSEMBLY

1Assembling the Stand (Fig. 5)

SZ2-STU1 SZ2-STU3

Applicable

microscope body

Horizontal arm

Allen wrench

Clamping screws

(x 2)

Drop prevention ring

Column

Clamping screws

(x 2)

Base plate

Allen wrench

Connect the

ground lead wire.*

Table clamp

section

Clamping screws

(x 2)

Allen wrench

Connect the ground

lead wire.**

To maintain the ESD protection performance,

be sure to ground the equipment using the

following tools.

*4 mm banana plug connection holes (x 4)

Bare ground lead wire connection screw (x 1)

** Bare ground lead wire connection screw (x 1)

Attach the column by firmly tightening the screws using the Allen

wrench.

Insert the drop prevention ring below the horizontal arm, in close

contact with it.

}It is convenient to store the Allen wrench in the Allen wrench storage

position on the horizontal arm for future use.

2Attaching the Bonder Arm (Fig. 6)

1. Lift the operation mistake prevention ring on the shaft at the distal end of

the horizontal arm, and screw in the provided clamping screws into the

two screw holes by about half using the Allen wrench.

Insert the bonder arm from the bottom side all the way up until it is

stopped.

2. Tighten the clamping screws firmly using the Allen wrench. When you

remove your hand from the operation mistake prevention ring, it drops to

hide the screws.

Be sure to attach the bonder arm firmly with the screws. Otherwise,

it may rotate or drop and cause danger.

Bonder Arm

SZ2-STB1

Fig. 7

Fig. 9

Bonder arm rotation

clamping knob

Horizontal rotation/

vertical clamping knob

Horizontal movement

clamping knob

Drop prevention ring

clamping knob

Distal end

rotation screws

(x 2)

OPERATION

1. To move the horizontal arm horizontally along the arm shaft, loosen the

horizontal movement clamping knob. Lift the microscope slightly for

smooth movement.

2. To rotate the horizontal arm by 360° around the column, loosen the hori-

zontal rotation clamping knob.

When rotating the horizontal arm, confirm that that the drop prevention

ring clamping knob is tightened firmly and in close contact with the

horizontal arm section.

3. To move the horizontal arm upward, keep the drop prevention ring clamp-

ing knob tightened but loosen the vertical clamping knob. After lifting the

horizontal arm to the desired position, tighten the vertical clamping knob

again. And then move up the drop prevention ring till immediately be-

neath the horizontal arm section and clamp the ring again.

To move the horizontal arm downward, always move down and clamp

the drop prevention ring before moving the horizontal arm downward.

Never loosen two clamping knobs simultaneously, as this is extremely

dangerous.

4. To rotate the bonder arm horizontally, loosen the bonder arm rotation

clamping knob. (Fig. 8)

5. To rotate the distal end of the horizontal arm with respect to the arm,

loosen the two screws at the distal end using the provided Allen wrench.

(Fig. 9)

Fig. 8

SZ2-STU1/STU3

Rotating the distal end enables observation of a perpendicular plane or

tall specimen. (Fig. 10)

Be particularly sure to tighten the distal end rotation screws tightly. If

they are loose, the distal end may rotate suddenly.

Do not tighten the distal end rotation screws too much, as this may

cause the distal end to slip out of the horizontal arm.

The stability is degraded if the distal end is attached on the side or

above the horizontal arm. In this case, take care to increase the

stability of the base plate.

Fig. 10

Fig. 11

6. To change the angle of the bonder arm, loosen the bonder arm angle

adjustment screw. (Fig. 11)

For the adjustment of the bonder arm angle, read the instruction manual

for the Arm Used with Microscope for Equipment Mounting.

Do not adjust the angle while the microscope body is mounted.

Dismount it before the adjustment.

SZ2-STU2

IMPORTANT

SAFETY PRECAUTIONS

1. Install the stand on a level desktop (inclination less than 3°).

2. When moving the stand, make sure that the clamping mechanisms are

secured tightly and lift the stand by holding it by the base plate. If the

stand is held by the horizontal arm or column alone, the base plate may

drop.

3. The load of the stand is limited, and its stability is variable depending on

the orientation of the horizontal arm. (Fig. 12)

· When the horizontal arm is extended at maximum, the load to the arm

of the SZX stand arm is limited as shown in the following table.*

Front 90° Max. 10 kg

(Max. 8.8 kg)

Left side 105°

Right side 100°

Rear 65° Max. 7 kg

(Max. 5.8 kg)

The figures inside ( ) are the loads when the SZX stand arm, weighing

1.2 kg, is used.

*Under this condition, the stand

tends to topple down easily if an-

other load is applied during the

microscope operation. It is rec-

ommended to set the horizontal

arm as short as possible.

· When the mounted microscope is heavy, set the horizontal arm rotation

stopper for the front 90° positioning. (For the method of this operation,

see page 11.)

4. When the mounted microscope has a TV camera or photography unit

mounted on it, do not tilt the microscope body. As the microscope is heavy

and the center of gravity of the system is located high, loosening the clamping

lever may cause the microscope to rotate suddenly, causing damage to

the TV camera, photography unit or microscope body. (Fig. 13) (For the

method of this operation, see page 13.)

Fig. 12

Max. 6 kg

(Max. 4.8 kg)

Fig. 13

Top view

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de laboratorio de Olympus

Olympus

Olympus HysteroFlow Manual de usuario

Olympus

Olympus SZX2-ILLT Manual de usuario

Olympus

Olympus U-UCD8A Manual de usuario

Olympus

Olympus U-PCD2 Manual de usuario

Olympus

Olympus CX-DO Manual de usuario

Olympus

Olympus CIX100 Manual de usuario

Olympus

Olympus SZ2-STS Manual de usuario

Olympus

Olympus SZX-DO Manual de usuario

Olympus

Olympus U-HGLGPS Manual de usuario

Olympus

Olympus U-UCD8 Manual de usuario

Olympus

Olympus U-APT Manual de usuario

Olympus

Olympus ENDO-AID Manual de usuario

Olympus

Olympus U-AFA2M-VIS Manual de usuario

Olympus

Olympus SZX2-ILR66 Manual de usuario

Olympus

Olympus U-RFLT50 Manual de usuario

Olympus

Olympus 72DL PLUS Manual de usuario

Olympus

Olympus U-SRG Manual de usuario

Olympus

Olympus SZ2-ILLC Manual de usuario

Olympus

Olympus DP2-SAL Manual de usuario

Olympus

Olympus R1 Manual de usuario

Olympus

Olympus SZX-RFL3 Manual de usuario

Olympus

Olympus SZX2 Series Manual de usuario

Olympus

Olympus OMCL-AC160TS-W2 Manual de usuario

Olympus

Olympus BioLever mini Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario