OHAUS 5000 Manual de usuario

Quick Start Guide Defender™5000

Ohaus Corporation www.ohaus.com iDefender™5000 (with T51 Indicators)

ASSEMBLY

Attach Indicator Mounting

and secure Load Cell Cable.

Remove Scale and

Accessories from carton. Attach Indicator to Bracket.

Attach Bracket to Column.

Connect Power Cord to Indicator.

Plug Power Supply to Wall Outlet.

Install Platform.

Adjust leveling feet.

Remove Shipping

Spacers.**

**Not included with

some models. x 4

The T51XW is supplied with a grounded power cable.

Use only with a compatible grounded power outlet.

Defender™5000 Quick Start Guide

Defender™5000 (with T51 Indicators) ii Ohaus Corporation www.ohaus.com

SAFETY PRECAUTIONS

For safe and dependable operation of this product, please comply with the following

safety precautions:

•Verify that the input voltage printed on the power Adapter and the plug type matches

the local power supply.

•Make sure that the power cord does not pose an obstacle or tripping hazard.

•Disconnect the product from the power supply when cleaning.

•Do not operate this product in hazardous or unstable environments.

•Do not drop loads on the pan.

•Use only approved accessories and peripherals, as available.

•Operate the product only under ambient conditions specified in the Instruction Manual.

•Service should be performed by authorized personnel only.

CONTROLS

Button

Primary Function

(Short Press) ON/ZERO

Turns the Indicator on

If Indicator is on,

sets zero.

Sends the current value to

the COM port if AUTOPRINT

is set to Off.

FUNCTION

Initiates an application mode.

Temporarily displays the

active mode’s reference data.

TARE

Performs a tare

operation.

Secondary

Function

(Long Press)

Off

Turns the Indicator off. Units

Changes the weighing unit. Mode

Allows changing the

application mode.

Press and hold allows

scrolling through modes.

Enter the User menu.

Menu Function

(Short Press) Yes

Accepts the current

setting on the display.

Advances to the next menu

or menu item.

Rejects the current setting on

the display and advances to

the next available setting.

Increments the value.

Back

Moves back

to previous menu item.

Decrements the value.

Exit

Exits the User menu.

Aborts a calibration in

progress.

Center of Zero

symbol

Preset Tare,

Tare, Brutto,

Gross symbols

Kilogram, Gram,

Percent, Pound,

Ounce, Pound:

Ounce, Tonne,

Pieces symbols

Capacity label

windo

Under, Accept

& Over LEDs

Range symbol

Scale symbol

(

not used

)

Dynamic weighing

symbol

Battery charge

symbol

Stability symbol

Net symbol

Quick Start Guide Defender™5000

Ohaus Corporation www.ohaus.com iii Defender™5000 (with T51 Indicators)

OPERATION

On/Off: To turn Indicator on, press ON. Indicator runs a display test,

shows a series of informational displays, and enters active weighing mode.

To turn Indicator off, press and hold Off until OFF appears.

Press ZERO to zero the weight display. Scale must be stable.

Scale zeros automatically at Power On.

Manual Tare: If weighing an item in a container, place empty container on

the scale. Before taring, container’s weight is shown (example 0.5 kg).

Press TARE. Display shows zero.

(If container is removed, display shows container’s weight as negative.)

To clear the Tare value, empty the scale and press TARE.

The display shows gross weight (zero if scale is empty).

Weighing: Place the item to be weighed on the scale.

(Sample shown: 1.5 kg, Gross weight.)

Verify the indicator: place a known mass on the scale and check if the reading is accurate.

If not, calibrate, using the Calibration Guide.

ADDITIONAL OPERATIONS

Changing Units of Measure: Press and hold Units until the desired

measuring unit appears. Only measuring units enabled in the Unit Menu are

displayed. (See back page.)

Printing Data: Press PRINT Units to send displayed data to the communication port.

(Auto-Print Mode must be Off).

Communication parameters in the Print and Communication Menu must be set.

(See Instruction Manual).

Application Modes: Press and hold the Mode button until the desired

application mode appears. WEIGH is default mode.

To have other modes accessible through Mode button, first turn

them On in the MODE menu. (See back page.)

When modes are On, choose by toggling through available options

by pressing Mode.

For details on various application modes, see Instruction Manual.

Weigh

Count

Percent

Dynamic

Checkweigh

Off, On

Off, Manual

Off, On

Defender™5000 Quick Start Guide

Defender™5000 (with T51 Indicators) iv Ohaus Corporation www.ohaus.com

MENU NAVIGATION

Press and hold the Menu button until MENU appears on the display.

Use Yes, No, Back,and Exit to navigate in Menu Mode:

– Yes Allows entry / Accepts displayed setting and advances to next menu item.

– No Skips displayed menu / Rejects setting or item, advances to next available item.

– Back Moves backwards through menus.

– Exit Exits directly to active weighing mode.

MENU STRUCTURE (For more details, see Instruction Manual.)

CALIBRATION SETUP READOUT MODE UNIT GMP PRINT-1

Zero

Span

Linearity

CAL Test

GEO

End CAL

Reset

Range

Capacity

Graduation

Power on Unit

Zero Range

Auto Tare

Retain Weight

Legal For Trade

Beeper Volume

Beeper Signal

Button Beeper

End Setup

Reset

Stable Range

Filter

Auto Zero

Backlight

Auto Off Timer

Gross Indicator

End Readout

Reset

Weigh

Count

Percent

Dynamic

Check Weigh

End Mode

Reset

Kilgram

Pound

Gram

Ounce

Pound Ounce

Tonne

Custom

End Unit

Reset

Date

Time

User ID

Project ID

Scale ID

End GMP

Reset

Stable Print

Auto Print

Content

Layout

End Print-1

PRINT-2 COM1 COM2 I-O LOCK MENU LOCK KEY END

Reset

Stable Print

Auto Print

Content

Layout

End Print-2

Reset

Baud

Parity

Stop

Handshake

Alt. Command

End COM1

Reset

Baud

Parity

Stop

Address

Handshake

Alt. Command

End COM2

Reset

External Input

Input Beep

Relay Output

Stable

End I-O

Reset

Lock Cal

Lock Setup

Lock Readout

Lock Mode

Lock Unit

Lock Print1

Lock Print2

Lock COM1

Lock COM2

Lock GMP

Lock I-O

End Lock Menu

Reset

Lock All

Lock Off

Lock Zero

Lock Print

Lock Unit

Lock Function

Lock Mode

Lock Tare

Lock Menu

End Lock Key

*80252987* P/N 80252987

Otros manuales para 5000

Tabla de contenidos

Otros manuales de Escala de OHAUS

OHAUS

OHAUS 5000 Manual de usuario

OHAUS

OHAUS Ranger Counting Scale Manual de usuario

OHAUS

OHAUS Defender D30BR Manual de usuario

OHAUS

OHAUS Valor 1000 Manual de usuario

OHAUS

OHAUS Defender 3000 Series Manual de usuario

OHAUS

OHAUS VF Series Manual de usuario

OHAUS

OHAUS CKW Series Manual de usuario

OHAUS

OHAUS CS200P Manual de usuario

OHAUS

OHAUS TROOPER Manual de usuario

OHAUS

OHAUS Pioneer Manual de usuario

OHAUS

OHAUS ES series Manual de usuario

OHAUS

OHAUS Navigator Rechargeable Battery Manual de usuario

OHAUS

OHAUS EXPLORER PRO Manual de usuario

OHAUS

OHAUS Ranger 3000 Series Manual de usuario

OHAUS

OHAUS DEFENDER SERIES Manual de usuario

OHAUS

OHAUS Traveler Series Manual de usuario

OHAUS

OHAUS Defender 3000 Series Manual de usuario

OHAUS

OHAUS TROOPER SCALE Manual de usuario

OHAUS

OHAUS ES50R Manual de usuario

OHAUS

OHAUS CS Series Manual de usuario

OHAUS

OHAUS adventurer+ Manual de usuario

OHAUS

OHAUS 1119-D0 Manual de usuario

OHAUS

OHAUS 5-0-2 Manual de usuario

OHAUS

OHAUS AV53 Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario