OHAUS Scout pro Guía de instalación

Scout Pro FAQ

AppNotes.v20170811_ AG

For any further questions, please e-mail us at techsupport@ohaus.com, or call us at 973-377-9000 #2 or ext. 7852 from 8AM to 5PM EST

Topic:

This list compiles frequently asked questions about the Scout Pro:

a) How do I turn on the units of measure

b) How do I switch between units of measure

c) How do I calibrate my unit

How to Turn On Units of Measure

Enabling or disabling the units of measure can be accomplished in the UNITS menu.

You can also click here for the user manual -- refer to Section 3: Operations, pages EN-11 (navigating the

main menu) and EN-13 (entering the UNIT menu).

Note1: during MENU navigation, use the following

buttons to initiate selections YES or NO.

Note2: depending on the region,the [ON/ZERO

Off] button may be designated as [ON/ 0/T Off].

1. With the scale (and lock switch) OFF: press

and hold [ON/ZERO Off] (approx. 5 seconds)

until the scale flashes MENU.

2. Release the button once MENU is displayed

After releasing the button, the scale will

display CAL.

3. Press [PRINT Unit] repeatedly until UNIT is

displayed.

4. Once UNIT is displayed, press [ON/ZERO Off]

to select this menu.

YES

. . .

Scout Pro FAQ

AppNotes.v20170811_ AG

For any further questions, please e-mail us at techsupport@ohaus.com, or call us at 973-377-9000 #2 or ext. 7852 from 8AM to 5PM EST

5. Press [PRINT Unit] repeatedly to cycle

through available units of measure.

6. In this example, you want to turn on grams:

Once "g" is displayed, press [ON/ZERO Off]

to select this unit of measure.

7. The current setting is displayed flashing (in

this case: OFF).

Press [PRINT Unit] until "ON" is displayed.

8. Once "ON" is displayed, press [ON/ZERO

Off] to select this setting.

Grams is now turned on and available when

you switch through units of measure during

operations.

9. To exit from the menu and return to

operations:

Press [ON/ZERO Off] again to revert to the

UNIT menu.

10. When UNIT is displayed, press [PRINT Unit]

until END is displayed.

11. Once END is displayed, press [ON/ZERO

Off] to exit from the menu and return to

operations.

Scout Pro FAQ

AppNotes.v20170811_ AG

For any further questions, please e-mail us at techsupport@ohaus.com, or call us at 973-377-9000 #2 or ext. 7852 from 8AM to 5PM EST

How to Switch Between Units of Measure

Long-press [PRINT Unit] to scroll through the enabled units of measure.

If the desired unit of measure is not displayed, make sure it is enabled in the UNITS Menu (see previous

section: How to turn on units of measure).

Press and hold [PRINT Unit] to scroll through the

enabled units of measure.

In this example, the scale is scrolling through

grams and ounces.

Release the button once the desired unit of

measure is displayed.

In this example, grams ("g").

Hint:

For OHAUS products, the second line on the

button generally means a secondary function that

is activated with a long-press.

. . .

Long-press

Scout Pro FAQ

AppNotes.v20170811_ AG

For any further questions, please e-mail us at techsupport@ohaus.com, or call us at 973-377-9000 #2 or ext. 7852 from 8AM to 5PM EST

How to Calibrate

The Scout Pro has two methods of calibration: Span and Linearity. Following is a quick guide on how to

perform a Span calibration.

You can also click here for the user manual -- refer to Section 3: Operations, pages EN-14 and EN-15

(Calibration).

Span calibration uses two calibration points: zero and a specified calibration weight (usually full scale

capacity). Before beginning calibration, make sure the Lock Switch is off, and you have the appropriate

calibration masses.

1. With the scale (and lock switch) OFF: press

and hold [ON/ZERO Off] (approx. 5 seconds)

until the scale flashes MENU.

2. Release the button once MENU is displayed

After releasing the button, the scale will

subsequently display CAL.

Make sure the pan is empty.

3. Press [ON/ZERO Off] to initiate Span

calibration.

4. "-C-" is displayed while the scale is acquiring

the zero value.

5. After establishing the zero point, the second

calibration value is displayed (in this

example, 200g).

. . .

Scout Pro FAQ

AppNotes.v20170811_ AG

For any further questions, please e-mail us at techsupport@ohaus.com, or call us at 973-377-9000 #2 or ext. 7852 from 8AM to 5PM EST

6. Place the requested calibration mass on the

pan, then press [ON/ZERO Off].

7. "-C-" is displayed while the scale is acquiring

the second value.

After establishing the second calibration

point, "DONE" is displayed.

Then the value of the calibration mass is

displayed.

The scale is now calibrated and ready for

operations.

8. Remove the calibration mass, and the scale

will return to zero.

Otros manuales para Scout pro

Tabla de contenidos

Otros manuales de Escala de OHAUS

OHAUS

OHAUS TROOPER SCALE Manual de usuario

OHAUS

OHAUS Ranger Count 2000 Series Manual de usuario

OHAUS

OHAUS Pioneer Manual de usuario

OHAUS

OHAUS Aviator 7000 Series Manual de usuario

OHAUS

OHAUS BW1.5US Manual de usuario

OHAUS

OHAUS AP110 Manual de usuario

OHAUS

OHAUS Emerald Manual de usuario

OHAUS

OHAUS JE 120 Manual de usuario

OHAUS

OHAUS Voyager V10640 Manual de usuario

OHAUS

OHAUS JD500 Manual de usuario

OHAUS

OHAUS VF Series Manual de usuario

OHAUS

OHAUS 30469913 Manual de usuario

OHAUS

OHAUS PR Series Manual de usuario

OHAUS

OHAUS Adventurer series Manual de usuario

OHAUS

OHAUS Defender 3000 Series Manual de usuario

OHAUS

OHAUS SD75L Manual de usuario

OHAUS

OHAUS ES6R Manual de usuario

OHAUS

OHAUS 1500 Series Manual de usuario

OHAUS

OHAUS HH 320 Manual de usuario

OHAUS

OHAUS CS Series Manual de usuario

OHAUS

OHAUS PS121 Manual de usuario

OHAUS

OHAUS Catapult 1000 Manual de usuario

OHAUS

OHAUS Ranger 4000 Count Series Manual de usuario

OHAUS

OHAUS Explorer EX1241 Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario