Nice OXILR Manual de usuario

OXILR

Nice

Radio receiver

EN - Instructions and warnings for installation and use

IT - Istruzioni ed avvertenze per l’installazione e l’uso

FR - Instructions et avertissements pour l’installation et l’utilisation

ES - Instrucciones y advertencias para la instalación y el uso

DE - Installierungs-und Gebrauchsanleitungen und Hinweise

PL -Instrukcjeiostrzeżeniadoinstalacjiiużytkowania

NL - Aanwijzingen en aanbevelingen voor installatie en gebruik

RU - Инструкции и предупреждения по монтажу и эксплуатации

made in Italy

1- English

1PRODUCT DESCRIPTION

OXILR is a radio receiver designed for being installed on a control unit for automating gates, garage doors and

road barriers.

– All uses other than the intended use described and use in environmental conditions other than

those described in this manual should be considered improper and forbidden!

• Long-range two-way radio communication

The OXILR receiver is equipped with two-way radio technology guaranteeing “Long Range” radio communica-

tion and interfaces with two-way transmitters that adopt the “LR” two-way radio encoding system.

OXILR can both receive and transmit information from and to the transmitter and, in particular, includes the

following functions:

–thesendingoftheconrmation(tothetransmitter)thatthetransmittedcommandwasreceivedcorrectly;

–thesendingofthestatus(tothetransmitter)oftheautomation(forexample,whetherthegateisopenor

closed,oranyanomaliespresent).

• Other product characteristics

– The receiver is compatible with the “LR” two-way encoding system.

– The control unit’s receiver has 1024 memory locations to memorise transmitters: one location can alterna-

tively memorise a single transmitter(ifitskeysarememorisedasa“singleset”,withtheMode1procedures

–readParagraph3.1),ora single key(ifmemorisedwiththeMode2procedures–readParagraph3.2).

–Eachreceiverhasitsownidenticationnumber,knownasthe“Certicate”.Thisallowsforaccessingseveral

ENGLISH

Instructions translated from Italian

English - 2

operations,suchas,forexample:thememorisationofnewtransmitterswithouthavingtoaccessthereceiver,

and the use of the O-View programmer through its “BusT4” connection to the control unit.

–Thisreceivercanbeusedsolelywithcontrolunitsequippedwith“SM”-typeplugconnector(verifythemost

suitablecontrolunitsontheNiceproductcatalogueoronthewww.niceforyou.comwebsite).

– This receiver automatically recognises the characteristics of the control unit on which it is installed and self-

sets in the following way:

- If the control unit manages the “BusT4”, the receiver makes available up to 15 different commands.

- If the control unit DOES NOT manage the “BusT4”, the receiver makes available up to 4 different commands.

Important! – In both cases, the number and diversity of the available commands depend on the type and

model of the control unit adopted. The “Table of commands” of each control unit is shown in the respective

instruction manual.

3- English

2INSTALLATION AND CONNECTION

The receiver must be connected to the control unit by inserting it through the relevant slot:

01. Beforeinserting(orremoving)thereceiver,

disconnect the power supply to the control unit.

OFF

02. Connecttheantenna supplied to terminal 1 of the re-

ceiver, as shown in Fig. A. Alternatively, if the radio

signal reception must be improved through the instal-

lationofanexternalantennawithacoaxialcablewith

50Ωimpedance(typeRG58),thecoaxialcablemust

be connected directlytoterminals1and2ofthe

receiver(Fig.B),ignoringthe“antenna”terminal(if

present)onthecontrolpanel.

Fig. A Fig. B

03. Insert the receiver through the relevant opening on

the control unit.

RL1L2L3

Open

Stop/Set

Flash

Photo

Photo Test

Stop

GND

SbS

24 V

Aerial

English - 4

04. Restore the power supply to the control unit.

3MEMORISING / DELETING TRANSMITTERS IN THE RECEIVER

Verification of the TYPE OF ENCODING system adopted by the transmitters already memorised

01. Disconnect the power supply to the control unit then restore the

powersupplyandcountthenumberofashesemittedbyLEDB

on the receiver:

OFF

•1orangeash = transmitters with LR technology x 1

•5greenashesand1orangeash = no transmitter memorised x 5+1

5- English

WARNINGS for carrying out the programming procedures

•Duringtheexecutionoftheprogramming procedures, refer to Fig. 1 to identify key

Aand LED B on the receiver. • To understand the meaning of the icons featured in the

procedure, refer to the table, “Key to the symbols used in the manual”. • The proce-

dureshavealimittime;therefore,beforeimplementingthem,itisimportanttoreadand

understand all the steps to be completed.

KEY TO THE SYMBOLS USED IN THE MANUAL

Symbol Description

(onthereceiver)LED“B”STEADYLIT

(onthereceiver)LED“B”LONGFLASH

(onthereceiver)LED“B”QUICKFLASH

(onthereceiver)LED“B”OFF

OFF

Disconnect power supply / Restore power supply

English - 6

5 s

Wait ...

>5 sec <Perform the operation within 5 seconds ...

Hold down key “A” of the receiver

Press and release key “A” of the receiver

Release key “A” of the receiver

Press and release the desired transmitter key

Hold down the desired transmitter key

Release the desired transmitter key

Read the control unit’s instruction manual

7- English

... Observe when LED “B” emits signals

ThesystemcanbeprogrammedinMode1orinMode2:seeParagraphs3.1and3.2.

3.1 - Memorisation in “Mode 1”

While Procedure 1 is being carried out, the receiver memorises all the command keys present on the transmit-

ter, automatically assigning output 1 of the receiver to the 1stkey,output2tothe2nd key, and so forth. Once the

procedure terminates, the memorisation will occupy a single memory location and the command associated

with each key will depend on the “List of commands” present on the automation’s control unit.

PROCEDURE 1 - Mode 1 memorisation

01. On the receiver: hold down key A and wait for the green LED

B to light up. Subsequently, release key A.

02. On the transmitter being memorised:

 (within10seconds)onthetransmitter:press and immediately

release any command key; LED B (on the receiver) will flash

green3times(=memorisationcompletedcorrectly).(*1)

(*1) Note - Ifthereareothertransmitterstobememorised,repeatstep02withinthenext10seconds.

The procedure will terminate automatically once this time elapses.

3.2 - Memorisation in “Mode 2”

WhileProcedure2isbeingcarriedout,thereceivermemorisesa single key among those present on the trans-

English - 8

mitter, associating it with the receiver output chosen by the installer. To memorise further keys, repeat the pro-

cedure from the beginning for each key to be memorised. Once the procedure terminates, the memorisation

will occupy a single memory location and the command associated with the memorised key will be that chosen

by the installer from the “List of commands” of the automation’s control unit. Note - A key can be associated

with only one output, while the same output can be associated with multiple keys.

PROCEDURE 2 - Mode 2 memorisation (and extended Mode 2)

01. In the control unit manual: choose the command to be memo-

rised and remember its “identification number”.

02. On the receiver: press and release key A for a number of times

matching the number that identifies the command chosen at

step 01: LED B will flash the same number of times.

xNo.....

=...

03. On the transmitter with the key to be memorised:

 (within10seconds)onthetransmitter:press and immediately

releasethekeytobememorised;LEDB(onthereceiver)will

flashgreen3times(=memorisationcompletedcorrectly).(*2)

(*2) Note - Ifthereareotherkeystobememorised(belongingtoothertransmitters)with the same com-

mand,repeatstep03withinthenext10secondsforeachfurtherkeytobememorised(theprocedure

terminatesoncethistimeelapses).

3.3 - Memorising (in the receiver) the control unit Series/Address, for the BusT4 network

The OXILR receiver can interact with a single control unit through the “BusT4” network. If the system contains

multiple control units connected to each other via “BusT4”, before carrying out the following procedure the

cable of the “BusT4” network must be disconnected from the control unit on which the Series/Address will be

memorised.

9- English

PROCEDURE 4 - Memorising (in the receiver) the control unit Series/Address, for the BusT4

network

01. Disconnect the power supply and wait 5 seconds.

OFF

5 s

02. Hold down key A of the receiver and simultaneously restore the

power supply:

LEDBemitssomeinitialashes(Chapter3);itwillthenemit2

shortorangeashes;lastly,whenthesteadygreenlightappears

(*3), release key A.

...

(*3) Note - If the LED emits a steady red light, it means that the memorisation procedure was not com-

pleted. In this case, repeat the procedure from the beginning.

WARNING! - Once the Series/Address has been memorised, the receiver will drive the control unit only through

BusT4. The Stand-By function cannot be active on the control unit. To enable the Stand-By function on the control

unit, do not run the “Memorising the control unit Series/Address for the BusT4 network” procedure.

Otros manuales para OXILR

Tabla de contenidos

Idiomas:

Otros manuales de Receptor de Nice

Nice

Nice BIO Series Manual de usuario

Nice

Nice SMXI Manual de usuario

Nice

Nice OXIBD Manual de usuario

Nice

Nice SMX2 Manual del producto

Nice

Nice TT2Z K Instrucciones de funcionamiento

Nice

Nice TT2Z Instrucciones de funcionamiento

Nice

Nice OXILR Especificaciones técnicas

Nice

Nice HSTT2L Manual de usuario

Nice

Nice elero Revio-868 SW Manual de usuario

Nice

Nice elero Revio-868 SW Manual de usuario

Nice

Nice FLOR Especificaciones técnicas

Nice

Nice NICEONE OXI SERIES Manual del producto

Nice

Nice NiceOne OX4T Instrucciones de funcionamiento

Nice

Nice Apollo FLOR FLOXR Series Especificaciones técnicas

Nice

Nice OXIBD Manual de usuario

Nice

Nice OXIBD Especificaciones técnicas

Nice

Nice RMF3004 Manual de usuario

Nice

Nice TT2N Especificaciones técnicas

Nice

Nice TTD0110 Especificaciones técnicas

Nice

Nice FLO Series Manual de usuario

Nice

Nice FLOX1 Manual de usuario

Nice

Nice NiceOne OXI/A Series Especificaciones técnicas

Nice

Nice FLOXMR Manual de servicio

Nice

Nice OXI Especificaciones técnicas

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario