Nice OXILR Especificaciones técnicas
OXILR
OXILR/A
Nice
Radio receiver
EN - Instructions and warnings for installation and use
made in Italy
1- English
EN
1PRODUCT DESCRIPTION
OXILR (OXILR/A) is a radio receiver designed for being installed on a control unit for automating gates, garage
doors and road barriers.
– All uses other than the intended use described and use in environmental conditions other than
those described in this manual should be considered improper and forbidden!
WARNINGS
This device must be professionally installed. The only permitted antenna is a 17 cm whip included.
Changeable antenna that must be professionally installed. For the OXILR/A do not use the coaxial
cable but connect the whip cable included.
• Long-range two-way radio communication
The OXILR (OXILR/A) receiver is equipped with two-way radio technology guaranteeing “Long Range” radio
communication and interfaces with two-way transmitters that adopt the “LR” two-way radio encoding system.
OXILR (OXILR/A) can both receive and transmit information from and to the transmitter and, in particular, in-
cludes the following functions:
–thesendingoftheconrmation(tothetransmitter)thatthetransmittedcommandwasreceivedcorrectly;
– the sending of the status (to the transmitter) of the automation (for example, whether the gate is open or
closed, or any anomalies present).
• Other product characteristics
– The receiver is compatible with the “LR” two-way encoding system.
– The control unit’s receiver has 1024 memory locations to memorise transmitters: one location can alterna-
tively memorise a single transmitter (if its keys are memorised as a “single set”, with the Mode 1 procedures
ENGLISH
Instructions translated from Italian
EN
English - 2
– read Paragraph 3.1), or a single key (if memorised with the Mode 2 procedures – read Paragraph 3.2).
– This receiver can be used solely with control units equipped with “SM”-type plug connector (verify the most
suitable control units on the Nice product catalogue or on the www.niceforyou.com website).
– This receiver automatically recognises the characteristics of the control unit on which it is installed and self-
sets in the following way:
- If the control unit manages the “BusT4”, the receiver makes available up to 15 different commands.
- If the control unit DOES NOT manage the “BusT4”, the receiver makes available up to 4 different commands.
Important! – In both cases, the number and diversity of the available commands depend on the type and
model of the control unit adopted. The “Table of commands” of each control unit is shown in the respective
instruction manual.
2INSTALLATION AND CONNECTION
The receiver must be connected to the control unit by inserting it through the relevant slot:
01. Before inserting (or removing) the receiver,
disconnect the power supply to the control unit.
OFF
02. Connect the antenna supplied to terminal 1 of the re-
ceiver, as shown in Fig. A. Alternatively, if the radio
signal reception must be improved through the instal-
lation of an external antenna with a coaxial cable with
50Ωimpedance(typeRG58),thecoaxialcablemust
be connected directly to terminals 1 and 2 of the
receiver (Fig. B), ignoring the “antenna” terminal (if
present) on the control panel.
1
2
1
2
1
2
Fig. A Fig. B
3- English
EN
03. Insert the receiver through the relevant opening on
the control unit.
RL1L2L3
Close
Open
Stop/Set
Flash
Photo
Photo Test
Stop
GND
SbS
24 V
Aerial
04. Restore the power supply to the control unit.
ON
3MEMORISING / DELETING TRANSMITTERS IN THE RECEIVER
Verification of the TYPE OF ENCODING system adopted by the transmitters already memorised
01. Disconnect the power supply to the control unit then restore the
powersupplyandcountthenumberofashesemittedbyLEDB
on the receiver:
OFF
ON
•1orangeash = transmitters with LR technology x 1
EN
English - 4
•5greenashesand1orangeash = no transmitter memorised x 5+1
WARNINGS for carrying out the programming procedures
• During the execution of the programming procedures, refer to Fig. 1 to identify key
Aand LED B on the receiver. • To understand the meaning of the icons featured in the
procedure, refer to the table, “Key to the symbols used in the manual”. • The proce-
dureshavealimittime;therefore,beforeimplementingthem,itisimportanttoreadand
understand all the steps to be completed.
1
2
AB
1
KEY TO THE SYMBOLS USED IN THE MANUAL
Symbol Description
(on the receiver) LED “B” STEADY LIT
(onthereceiver)LED“B”LONGFLASH
(onthereceiver)LED“B”QUICKFLASH
(on the receiver) LED “B” OFF
5- English
EN
OFF
ON
Disconnect power supply / Restore power supply
5 s
Wait ...
>5 sec <Perform the operation within 5 seconds ...
1
2
Holddownkey“A”ofthereceiver
1
2
Press and release key “A” of the receiver
1
2
Release key “A” of the receiver
Press and release the desired transmitter key
Holddownthedesiredtransmitterkey
EN
English - 6
Release the desired transmitter key
Read the control unit’s instruction manual
... Observe when LED “B” emits signals
The system can be programmed in Mode 1 or in Mode 2: see Paragraphs 3.1 and 3.2.
7- English
EN
3.1 - Memorisation in “Mode 1”
While Procedure 1 is being carried out, the receiver memorises all the command keys present on the transmit-
ter, automatically assigning output 1 of the receiver to the 1st key, output 2 to the 2nd key, and so forth. Once
the procedure terminates, the memorisation will occupy a single memory location and the command associ-
ated with each key will depend on the “List of commands” present on the automation’s control unit.
PROCEDURE 1 - Mode 1 memorisation
01. On the receiver: hold down key A and wait for the green LED
B to light up. Subsequently, release key A.
1
2
1
2
02. On the transmitter being memorised:
(within 10 seconds) on the transmitter: press and immediately
release any command key; LED B (on the receiver) will flash
green 3 times (=memorisation completed correctly). (*1)
(*1) Note - If there are other transmitters to be memorised, repeat step 02 within the next 10 seconds.
The procedure will terminate automatically once this time elapses.
EN
English - 8
3.2 - Memorisation in “Mode 2”
While Procedure 2 is being carried out, the receiver memorises a single key among those present on the trans-
mitter, associating it with the receiver output chosen by the installer. To memorise further keys, repeat the pro-
cedure from the beginning for each key to be memorised. Once the procedure terminates, the memorisation
will occupy a single memory location and the command associated with the memorised key will be that chosen
by the installer from the “List of commands” of the automation’s control unit. Note - A key can be associated
with only one output, while the same output can be associated with multiple keys.
PROCEDURE 2 - Mode 2 memorisation (and extended Mode 2)
01. In the control unit manual: choose the command to be memo-
rised and remember its “identification number”.
02. On the receiver: press and release key A for a number of times
matching the number that identifies the command chosen at
step 01: LED B will flash the same number of times.
1
2
x No. ....
=...
03. On the transmitter with the key to be memorised:
(within 10 seconds) on the transmitter: press and immediately
releasethekeytobememorised;LEDB(onthereceiver)will
flash green 3 times (= memorisation completed correctly). (*2)
(*2) Note - If there are other keys to be memorised (belonging to other transmitters) with the same com-
mand, repeat step 03 within the next 10 seconds for each further key to be memorised (the procedure
terminates once this time elapses).
9- English
EN
3.3 - Memorising (in the receiver) the control unit Series/Address, for the BusT4 network
The OXILR (OXILR/A) receiver can interact with a single control unit through the “BusT4” network. If the system
contains multiple control units connected to each other via “BusT4”, before carrying out the following procedure
the cable of the “BusT4” network must be disconnected from the control unit on which the Series/Address will
be memorised.
PROCEDURE 4 - Memorising (in the receiver) the control unit Series/Address, for the BusT4
network
01. Disconnect the power supply and wait 5 seconds.
OFF
5 s
02. HolddownkeyAofthereceiverandsimultaneouslyrestorethe
power supply:
LEDBemits someinitialashes(Chapter 3);itwillthenemit2
shortorangeashes;lastly,whenthesteadygreenlightappears
(*3), release key A.
+
ON
1
2
1
2
...
Otros manuales para OXILR
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Receptor de Nice
Nice
Nice Apollo FLOR FLOXR Series Especificaciones técnicas
Nice
Nice FLO Series Manual de usuario
Nice
Nice elero Revio-868 SW Manual de usuario
Nice
Nice NICEONE OXI SERIES Manual del producto
Nice
Nice elero Revio-868 SW Manual de usuario
Nice
Nice TT2Z Instrucciones de funcionamiento
Nice
Nice FLOX1 Manual de usuario
Nice
Nice SMXI Manual de usuario
Nice
Nice FLOXMR Manual de servicio
Nice
Nice FLOR Especificaciones técnicas
Nice
Nice HSTT2L Manual de usuario
Nice
Nice Home RC200 Especificaciones técnicas
Nice
Nice TTD0110 Especificaciones técnicas
Nice
Nice OXILR Manual de usuario
Nice
Nice OXIBD Especificaciones técnicas
Nice
Nice OXI Especificaciones técnicas
Nice
Nice SMX2 Manual del producto
Nice
Nice OXIBD Manual de usuario
Nice
Nice HSRE12 Manual de usuario
Nice
Nice NiceOne OX4 Manual del producto
