National Instruments PXIe-8522 Manual de usuario
USER MANUAL
PXIe-8522/8523
4-port, 1000BASE-T1 and 100/1000BASE-T1 PXI Automotive
Ethernet Interface Modules
This document explains how to install and configure the PXIe-8522 and PXIe-8523
Automotive Ethernet interface modules.
Contents
Introduction...............................................................................................................................1
Getting Started.......................................................................................................................... 2
Installing the Module........................................................................................................ 2
Configuring the Module in MAX..................................................................................... 3
Connection Guidelines......................................................................................................4
Pinouts.......................................................................................................................................5
PXIe-8522 Pinout..............................................................................................................5
PXIe-8523 Pinout..............................................................................................................6
Port Modes................................................................................................................................ 6
Data Path Overview.......................................................................................................... 7
Direct Mode...................................................................................................................... 8
Tap Mode.......................................................................................................................... 9
PHY State................................................................................................................................10
Link Speed...............................................................................................................................11
Programming the Module........................................................................................................11
LED Functionality...................................................................................................................11
Synchronization Methods....................................................................................................... 12
Local Time...................................................................................................................... 12
Network Time................................................................................................................. 13
Host Time........................................................................................................................13
PXI Triggers....................................................................................................................13
Introduction
The PXIe-8522 and PXIe-8523 modules are 4-port, unshielded twisted pair (UTP) Automotive
Ethernet interfaces for developing applications with the NI-XNET driver. These modules are
ideal for developing applications that require Automotive Ethernet to test and validate
automotive electronic control units (ECUs).
The PXIe-8522 module is fixed at 1000BASE-T1. The PXIe-8523 module is configurable
between 100BASE-T1 and 1000BASE-T1.
Kit Contents
• PXIe-8522 or PXIe-8523 module
• 26 AWG x 8 mm insulated ferrules, x 20
• Screw driver for use with connector spring terminal push buttons
•PXIe-8522 Safety, Environmental, and Regulatory Information or PXIe-8523 Safety,
Environmental, and Regulatory Information
Note This device ships with a plug connector pre-installed on each port.
Getting Started
Installing the Module
Notice To prevent damage to the module caused by ESD or contamination, handle
the module using the edges or the metal bracket.
1. Ensure the AC power source is connected to the chassis before installing the module.
The AC power cord grounds the chassis and protects it from electrical damage while you
install the module.
2. Power off the chassis.
3. Inspect the slot pins on the chassis backplane for any bends or damage prior to
installation. Do not install a module if the backplane is damaged.
4. Remove the black plastic covers from all the captive screws on the module front panel.
5. Identify a supported slot in the chassis. The following figure shows the symbols that
indicate the slot types.
Figure 1. Chassis Compatibility Symbols
NI PXIe-1062Q
12 3 45
1. PXI Express System Controller Slot
2. PXI Peripheral Slot
3. PXI Express Hybrid Peripheral Slot
4. PXI Express System Timing Slot
5. PXI Express Peripheral Slot
These modules can be placed in PXI Express peripheral slots, PXI Express hybrid
peripheral slots, or PXI Express system timing slots.
6. Touch any metal part of the chassis to discharge static electricity.
7. Ensure that the ejector handle is in the downward (unlatched) position.
8. Place the module edges into the module guides at the top and bottom of the chassis. Slide
the module into the slot until it is fully inserted.
2| ni.com | PXIe-8522/8523 User Manual
Figure 2. Module Installation
2
3
NI PXIe-1075
1
1. Chassis
2. Hardware Module
3. Ejector Handle in Downward (Unlatched) Position
9. Latch the module in place by pulling up on the ejector handle.
10. Secure the module front panel to the chassis using the front-panel mounting screws.
Note Tightening the top and bottom mounting screws increases mechanical
stability and also electrically connects the front panel to the chassis, which can
improve the signal quality and electromagnetic performance.
11. Cover all empty slots using EMC filler panels or fill using slot blockers to maximize
cooling air flow, depending on your application.
12. Power on the chassis.
Configuring the Module in MAX
Note NI-XNET software, which includes hardware drivers, can be installed before
or after the module is installed.
Use Measurement & Automation Explorer (MAX) to configure your NI hardware. MAX
informs other programs about which devices reside in the system and how they are configured.
1. Launch MAX.
2. In the configuration tree, expand Devices and Interfaces to see the list of installed NI
hardware.
Note If you do not see your module listed, press <F5> to refresh the list of
installed modules. If the module is still not listed, power off the system, ensure
the module is correctly installed, and restart.
3. Expand your module to see the list of ports.
4. Record the NI-XNET interface name that MAX assigns to each port of the hardware. Use
this name when programming the module.
PXIe-8522/8523 User Manual | © National Instruments | 3
5. For each port, configure the port mode to either Direct or Tap, depending on whether you
want to participate fully in network communication as an endpoint (Direct) or monitor an
existing network connection (Tap). Refer to the Port Modes section for more information.
6. For each port, configure the PHY state to either Master or Slave, depending on the
corresponding state of the PHY that you are connecting to. Refer to the Phy State section
for more information.
Note Two PHYs that are physically connected must be configured to use
opposing PHY states. One PHY must be configured to be the master, and the
other PHY must be configured to be the slave.
7. (PXIe-8523 only) For each port, configure the link speed to either 100 Mb/s or 1000
Mb/s. Refer to the Link Speed section for more information.
Note Two ports that are configured as Tap partners must be configured with
matching link speeds.
8. Self-test the hardware by selecting the item in the configuration tree and clicking Self-
Test in the MAX toolbar.
The MAX self-test performs a basic verification of hardware resources.
Connection Guidelines
Notice Operate this product only with cables less than 15 m in length.
1. Push a solid wire or ferrule directly into the terminal.
2. When inserting a stranded wire without a ferrule, first open the terminal by pressing the
push button with a finger or the included screwdriver tool.
3. Verify that all strands of a stranded wire are securely retained.
4. Insulated ferrules are recommended for small-gauge stranded wire. Insulated ferrules (26
AWG x 8 mm) are included with this product.
Note A ferrule crimping tool is not included with this product.
5. Tighten the connector screw flanges to the torque specification in the PXIe-8522
Specifications or PXIe-8523 Specifications for the best shock and vibration performance.
The connector screw flanges ship in a non-torqued configuration for easy removal.
6. When removing a wire, first open the terminal by pressing the push button with a finger
or the included screwdriver tool.
4| ni.com | PXIe-8522/8523 User Manual
Pinouts
PXIe-8522 Pinout
Figure 3. PXIe-8522 Pinout
PORT 1
LINK/
ACT
STATUS
TAP
PORT 2
LINK/
ACT
STATUS
PORT 3
LINK/
ACT
STATUS
TAP
PORT 4
LINK/
ACT
STATUS
PXIe-8522
1000BASE-T1
PORT 1
LINK/
ACT
STATUS
Link/Act
LED
Port Identification
Status
LED
Pin 1
Pin 2
Pin 3
Tap
Pairs
Ports
Table 1. PXIe-8522 Pinout Signal Descriptions
Pin Number Signal Type Signal Direction Signal Description Signal Required
1 TRX_P Bi-directional Transceiver plus Required
2 TRX_M Bi-directional Transceiver minus Required
3 Shield — Shield Optional
PXIe-8522/8523 User Manual | © National Instruments | 5
PXIe-8523 Pinout
Figure 4. PXIe-8523 Pinout
PORT 1
LINK/
ACT
STATUS
TAP
PORT 2
LINK/
ACT
STATUS
PORT 3
LINK/
ACT
STATUS
TAP
PORT 4
LINK/
ACT
STATUS
PXIe-8523
100/1000BASE-T1
PORT 1
LINK/
ACT
STATUS
Link/Act
LED
Port Identification
Status
LED
Pin 1
Pin 2
Pin 3
Tap
Pairs
Ports
Table 2. PXIe-8523 Pinout Signal Descriptions
Pin Number Signal Type Signal Direction Signal Description Signal Required
1 TRX_P Bi-directional Transceiver plus Required
2 TRX_M Bi-directional Transceiver minus Required
3 Shield — Shield Optional
Port Modes
The module includes four ports that can be configured as independent network interfaces. The
ports can function in Direct mode or Tap mode. Regardless of mode, traffic on each port can
be monitored. When monitoring is enabled, all traffic that is transmitted or received on that
6| ni.com | PXIe-8522/8523 User Manual
port is captured. Each packet is timestamped by both the local time keeper and the port's
network time keeper. The local time keeper runs off PXI Clk10 if present on the chassis. Each
port has an independent network time keeper, which uses IEEE 802.1AS to synchronize time
with other devices on the network.
Note Port mode cannot be changed while an XNET session is started on the port.
When the port mode is changed, port connectivity is lost while the change is
configured.
Data Path Overview
The following diagram describes each port within the module.
Figure 5. PXIe-8522/8523 Block Diagram
PXIe-8522/8523
User Application
PXIe Controller
XNET OS Stack
Intel i210
XNET
Monitor
XNET
Endpoint
DUT
802.1AS
Firmware
MAC
PHY
Each port has three data paths: XNET monitor, XNET endpoint, and OS stack. All three data
paths can be used simultaneously depending on port mode. The monitor path reads and
inspects all Ethernet frames that are received or transmitted on the port. The endpoint path
transmits and receives Ethernet frames on the port. The endpoint path is typically used if you
need it to act as an AVB endpoint. The OS stack path transmits and receives data using
standard network sockets via the operating system's network stack. The OS stack is typically
used with applications designed to use traditional TCP- or UDP-based protocols for its
network communication.
PXIe-8522/8523 User Manual | © National Instruments | 7
For Ethernet interfaces, the suffix "/monitor" indicates the use of a monitor path when it is
appended to the interface name. For example, "ENET1" specifies use of the endpoint path, and
"ENET1/ monitor" specifies use of the monitor path. The monitor path is used to read Ethernet
frames that are received or transmitted on each port. When Tap is enabled, data received via
the monitor path by a Tap pair will be identical on each port in the pair.
The IEEE 802.1AS protocol is implemented by the firmware running on the module, and
packet timestamps are taken near the device's physical layer. This helps guarantee a high
degree of synchronization accuracy for each port's network time.
Note The PXIe-8522 and PXIe-8523 modules only support jumbo frames at
1000BASE-T1. Refer to the Link Speed section for more information.
Direct Mode
The following diagram describes Direct mode on the module.
8| ni.com | PXIe-8522/8523 User Manual
Figure 6. Direct Mode
PXIe-8522/8523
User Application
PXIe Controller
XNET OS Stack XNET
XNET
Endpoint Intel i210 Intel i210 XNET
Endpoint
DUT1
MAC
PHY
DUT2
MAC
PHY
Note This diagram shows a design with two ports. Each of the device's four ports
can run independently under Direct mode.
Note Although it is not shown in the diagram, you can simultaneously use the
XNET monitor data path on each port while it is in Direct mode. This allows you to
analyze all network traffic that is transmitted and received on the port's endpoint.
In Direct mode, ports are directly connected and function as endpoints; Ethernet frames
received and transmitted on the port have no relationship to any other ports on the device.
Input and output sessions are supported in Direct mode. The module supports up to four ports
using Direct mode.
Tap Mode
In Tap mode, a pair of adjacent ports on the device, called tap partners, are connected to form a
Tap that allows the module to monitor traffic. In Tap mode, physical Port 1 and Port 2 are Tap
PXIe-8522/8523 User Manual | © National Instruments | 9
partners, and Port 3 and Port 4 are Tap partners. A frame received on one Tap partner is
transmitted out of the other Tap partner, which mimics the behavior of an Ethernet cable.
Note For more information about Tap latency, refer to the PXIe-8522
Specifications or PXIe-8523 Specifications.
When an input session is created using an XNET interface for either Tap partner, and the "/
monitor" suffix is used with the XNET interface, the session reads frames going through the
Tap partners. Output sessions are not supported in Tap mode.
Note You only need to select the monitor of one port in the Tap pairing. If both
monitors are selected, you will receive the same data twice.
Setting one port to Tap mode will automatically set the port's Tap partner to Tap mode. The
module supports two Taps (Ports 1/2 and Ports 3/4) using this mode. All four ports can also be
used simultaneously while one pair is in Tap mode and the other ports are in Direct mode. The
following diagram describes one Tap pair on the module.
Figure 7. Tap Mode
PHY
XNET
Monitor
PHY
PXIe-8522/8523
DUT1 DUT2
User Application
XNET XNET
PXIe Controller
PHY State
The module PHY's master/slave state can be configured for communication with its peer PHY.
In traditional Ethernet networks, this master/slave state is negotiated automatically at the PHY
level. However, in Automotive Ethernet networks, the master/slave state is commonly
configured statically and is typically determined by the PHY state setting of the connected
DUT. Configure the PHY state of the module's port to the opposite of the connected DUT's
PHY state.
10 | ni.com | PXIe-8522/8523 User Manual
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Unidad de control de National Instruments
National Instruments
National Instruments PCIe-7858 Manual de usuario
National Instruments
National Instruments NI 9375 Manual de usuario
National Instruments
National Instruments FP-AI-102 Manual de usuario
National Instruments
National Instruments NI FlexRIO PXI-7951R Manual de usuario
National Instruments
National Instruments NI-9232 Manual de usuario
National Instruments
National Instruments NI 9205 Manual de usuario
National Instruments
National Instruments FIeldPoint FP-AO-200 Manual de usuario
National Instruments
National Instruments GPIB-SBX Manual de usuario
National Instruments
National Instruments SCXI-1160 Manual de usuario
National Instruments
National Instruments NI 9882 Manual de usuario
National Instruments
National Instruments NI 9265 Manual de usuario
National Instruments
National Instruments SCXI-1520 Manual
National Instruments
National Instruments 9238 Manual de uso y cuidado
National Instruments
National Instruments NI 9225 Manual
National Instruments
National Instruments PXIe-4310 Manual de usuario
National Instruments
National Instruments NI 9751 Manual de usuario
National Instruments
National Instruments PXIe-5698 Manual de usuario
National Instruments
National Instruments SCXI SCXI-1102 Instrucciones de instalación y funcionamiento
National Instruments
National Instruments NI-9208 Manual de usuario
National Instruments
National Instruments NI 9246 Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
