National Instruments NI-5783 Manual de usuario

NI-5783

GETTING STARTED GUIDE

NI 5783

Four Channel Transceiver Adapter Module

Note Before you begin, complete the software and hardware installation

instructions in the getting started guide for your FlexRIO FPGA module or

Controller for FlexRIO.

The NI 5783 is a FlexRIO adapter module designed to work in conjunction with FlexRIO

FPGA modules and Controllers for FlexRIO.

The NI 5783 is available in two variants. The NI 5783-01 variant is a 40 MHz Elliptic Filter

(Frequency Domain). The NI 5783-02 variant is a 40 MHz Butterworth Filter (Time Domain).

Unless otherwise specified, all descriptions in this document refer to both variants.

The NI 5783 features 4 analog input channels with 16-bit resolution and sample rates up to

100 MS/s, and 4 analog output channels with 16-bit resolution and sample rates up to

100 MS/s or 200 MS/s.

Note The NI 5783 is compatible only with NI PXIe-797xR and NI-793xR devices.

This document explains how to install and configure the NI 5783.

Contents

Electromagnetic Compatibility Guidelines...............................................................................2

FlexRIO Documentation........................................................................................................... 2

Verifying the System Requirements..........................................................................................4

Unpacking................................................................................................................................. 4

Preparing the Environment....................................................................................................... 4

Installing the NI 5783............................................................................................................... 5

Confirming that Measurement & Automation Explorer (MAX) Recognizes the Device........ 5

Recommended Cables...............................................................................................................6

Accessories................................................................................................................................6

Front Panel and Connector Pinouts...........................................................................................6

AUX I/O Connector.......................................................................................................... 8

Block Diagram.......................................................................................................................... 9

Logic Diagram.......................................................................................................................... 9

Component-Level Intellectual Property (CLIP)..................................................................... 10

NI 5783 CLIP..................................................................................................................10

NI 5783 400 MSPS AO CLIP.........................................................................................11

Clocking.................................................................................................................................. 11

Worldwide Support and Services............................................................................................ 12

Where to Go Next................................................................................................................... 12

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits are designed to provide reasonable protection against harmful interference when the

product is operated in the intended operational electromagnetic environment.

This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with

radio and television reception and prevent unacceptable performance degradation, install and

use this product in strict accordance with the instructions in the product documentation.

Furthermore, any modifications to the product not expressly approved by National Instruments

could void your authority to operate it under your local regulatory rules.

Caution To ensure the specified EMC performance, operate this product only with

shielded cables and accessories.

Caution To ensure the specified EMC performance, the length of all I/O cables

must be no longer than 3 m (10 ft).

FlexRIO Documentation

Table 1. FlexRIO Documentation Locations and Descriptions

Document Location Description

Getting started guide

for your FlexRIO

FPGA module or

Controller for

FlexRIO

Available from the Start menu

and at ni.com/manuals.

Contains installation instructions

for your FlexRIO system.

Specifications

document for your

FlexRIO FPGA

module or Controller

for FlexRIO

Available from the Start menu

and at ni.com/manuals.

Contains specifications for your

FlexRIO FPGA module or

Controller for FlexRIO.

Getting started guide

for your adapter

module

Available from the Start menu

and at ni.com/manuals.

Contains signal information,

examples, and CLIP details for

your adapter module.

2| ni.com | NI 5783 Getting Started Guide

Table 1. FlexRIO Documentation Locations and Descriptions (Continued)

Document Location Description

Specifications

document for your

adapter module

Available from the Start menu

and at ni.com/manuals.

Contains specifications for your

adapter module.

LabVIEW FPGA

Module Help

Embedded in LabVIEW Help

and at ni.com/manuals.

Contains information about the

basic functionality of the

LabVIEW FPGA Module.

Real-Time Module

Help

Embedded in LabVIEW Help

and at ni.com/manuals.

Contains information about real-

time programming concepts, step-

by-step instructions for using

LabVIEW with the Real-Time

Module, reference information

about Real-Time Module VIs and

functions, and information about

LabVIEW features on real-time

operating systems.

FlexRIO Help Available from the Start menu

and at ni.com/manuals.

Contains information about the

FPGA module front panel

connectors and I/O, controller for

FlexRIO front panel connectors

and I/O, programming

instructions, and adapter module

component-level IP (CLIP).

FlexRIO Adapter

Module Development

Kit User Manual

Available from the Start menu

at Start»All Programs»

National Instruments»NI

FlexRIO»NI FlexRIO

Adapter Module Development

Kit»Documentation.

Contains information about how

to create custom adapter modules

for use with FlexRIO FPGA

modules.

LabVIEW Examples Available in NI Example

Finder. In LabVIEW, click

Help»Find Examples»

Hardware Input and Output»

FlexRIO.

Contains examples of how to run

FPGA VIs and Host VIs on your

device.

NI 5783 Getting Started Guide | © National Instruments | 3

Table 1. FlexRIO Documentation Locations and Descriptions (Continued)

Document Location Description

IPNet Located at ni.com/ipnet. Contains LabVIEW FPGA

functions and intellectual property

to share.

FlexRIO product page Located at ni.com/flexrio. Contains product information and

data sheets for FlexRIO devices.

Verifying the System Requirements

To use the NI 5783, your system must meet certain requirements. For more information about

minimum system requirements, recommended system, and supported application development

environments (ADEs), refer to the readme, which is available on the software media or online

at ni.com/updates.

Unpacking

Caution To prevent ESD from damaging the devices, ground yourself using a

grounding strap or by holding a grounded object, such as your computer chassis.

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove each module from the package and inspect it for loose components or any other

sign of damage.

Caution Never touch the exposed pins of connectors.

Note Do not install a device if it appears damaged in any way.

3. Unpack any other items and documentation from the kit.

Store the devices in the antistatic package when they are not in use.

Preparing the Environment

Ensure that the environment you are using the NI 5783 in meets the following specifications.

Operating temperature (IEC 60068-2-1,

IEC 60068-2-2)

0 °C to 55 °C

Operating humidity (IEC 60068-2-56) 10% to 90% RH, noncondensing

4| ni.com | NI 5783 Getting Started Guide

Pollution Degree 2

Maximum altitude 2,000 m at 25 °C ambient temperature

Indoor use only.

Note Refer to the NI 5783 Specifications at ni.com/manuals for complete

specifications.

Caution Clean the hardware with a soft, nonmetallic brush. Make sure that the

hardware is completely dry and free from contaminants before returning it to

service.

Installing the NI 5783

Refer to the getting started guide for your FlexRIO FPGA module or Controller for FlexRIO

for instructions about how to install your FlexRIO system, including the NI 5783.

Confirming that Measurement & Automation

Explorer (MAX) Recognizes the Device

Use Measurement & Automation Explorer (MAX) to configure your NI hardware. MAX

informs other programs about which devices reside in the system and how they are configured.

MAX is automatically installed with FlexRIO Support.

1. Launch MAX by navigating to Start»All Programs»National Instruments»NI MAX or

by clicking the NI MAX desktop icon.

2. In the Configuration pane, double-click Devices and Interfaces to see the list of installed

devices. Installed devices appear under the name of their associated chassis.

3. (PXI and PXI Express devices only) Expand your Chassis tree item. MAX lists all

devices installed in the chassis. Your default device names may vary.

Note If you do not see your hardware listed, press <F5> to refresh the list of

installed devices. If the device is still not listed, power off the system, ensure

the device is correctly installed, and restart.

4. (Controllers for FlexRIO only) Your device appears under the Remote Devices section.

NI 5783 Getting Started Guide | © National Instruments | 5

Recommended Cables

NI recommends using the following cables to connect signals to the NI 5783.

Cable NI Part Number

HDBNC to SMA 769177-01

HDBNC to BNC 769028-01

Accessories

The NI 5783 can be used with the SCB-19 shielded desktop connector block.

Refer to the SCB-19 User Guide for information about how to connect and use the SCB-19

with the AUX I/O front panel connector on your NI 5783.

Related Information

AUX I/O Connector on page 8

Front Panel and Connector Pinouts

The following figure shows the front panel connectors for the NI 5783.

6| ni.com | NI 5783 Getting Started Guide

Device Front Panel Connector Signal Description

200 MS/s AO

100 MS/s AI

16-Bit AO-AI

NI 5783

INSTRUMENTS

NATIONAL

AUX

I/O

TRIG

CLK/

REF

AI 3

AI 2

AI 1

AI 0

AO 3

AO 2

AO 1

AO 0

AO 0 Analog input channel, 50 Ω, single-ended, DC-coupled

AO 1

AO 2

AO 3

AI 0 Analog output channel, 50 Ω, single-ended, DC-

coupled

AI 1

AI 2

AI 3

CLK/REF IN External Reference Clock or Sample Clock input

TRIG Trigger input and output channel

AUX I/O Digital I/O and PFI connector

Caution To avoid permanent damage to the NI 5783, disconnect all signals

connected to the NI 5783 before powering down the module, and connect signals

only after the adapter module has been powered on by the FlexRIO FPGA module or

Controller for FlexRIO.

Caution Connections that exceed any of the maximum ratings of any connector on

the NI 5783 can damage the device and the chassis. NI is not liable for any damage

resulting from such connections.

NI 5783 Getting Started Guide | © National Instruments | 7

AUX I/O Connector

Table 2. NI 5783 AUX I/O Connector Pin Assignments

AUX I/O Connector Pin Signal Signal Description

1 DIO Port 0 (0) Bidirectional single-ended (SE) digital I/O (DIO)

data channel.

2 GND Ground reference for signals.

3 DIO Port 0 (1) Bidirectional SE DIO data channel.

4 DIO Port 0 (2) Bidirectional SE DIO data channel.

5 GND Ground reference for signals.

6 DIO Port 0 (3) Bidirectional SE DIO data channel.

7 DIO Port 1 (0) Bidirectional SE DIO data channel.

8 GND Ground reference for signals.

9 DIO Port 1 (1) Bidirectional SE DIO data channel.

10 DIO Port 1 (2) Bidirectional SE DIO data channel.

11 GND Ground reference for signals.

12 DIO Port 1 (3) Bidirectional SE DIO data channel.

13 PFI 0 Bidirectional SE DIO data channel.

14 NC No connect.

15 PFI 1 Bidirectional SE DIO data channel.

16 PFI 2 Bidirectional SE DIO data channel.

17 GND Ground reference for signals.

18 +5 V +5 V power (10 mA maximum).

19 PFI 3 Bidirectional SE DIO data channel.

Caution The AUX I/O connector accepts a standard, third-party HDMI cable, but

the AUX I/O port is not an HDMI interface. Do not connect the AUX I/O port on the

8| ni.com | NI 5783 Getting Started Guide

NI 5783 to the HDMI port of another device. NI is not liable for any damage

resulting from such signal connections.

Related Information

Accessories on page 6

The NI 5783 can be used with the SCB-19 shielded desktop connector block.

Block Diagram

The following figure shows the NI 5783 block diagram and signal flow.

Figure 1. NI 5783 Block Diagram

CH0 AI

CH1 AI

40 MHz

Anti-Alias

ADA4932

Analog Input

85 MHz

Noise Filter

CH2 AI

CH3 AI

TRIG IN/OUT

CLOCK_REF IN

Buffered Trigger I/O To FPGA Interface

10/100 MHz CMOS Clock

CH0 A0 MCX

CH1 A0 MCX

CH2 A0 MCX

CH3 A0 MCX

–

40 MHz

Anti-Alias

ADA4932 85 MHz

Noise Filter

–

40 MHz

Anti-Alias

ADA4932 85 MHz

Noise Filter

–

40 MHz

Anti-Alias

ADA4932 85 MHz

Noise Filter

–

40 MHz AA LMH6702

–

40 MHz AA LMH6702

–

40 MHz AA LMH6702

–

40 MHz AA LMH6702

Analog Input

Clocking

100 MHz LVPECL CLK

100 MHz LVDS CLK

DACCLK/8 OSTR LVPECL 100 MHz

VCXO

Loop-Filter

(PLL)

Phase/Freq

Adjust DAC

Ch A+

DACCLK

DATACLK =

2”DACCLK

Ch A Ch B Ch C Ch D

Ch B+

Ch B+ DAC3484

QUAD 16-bit

1.25 GSPS DAC

AD9511

Clock Distribution

& PLL

1 W Max

Power Supplies

(100 MS/s Data Rate

Interpolate x8 for

Fixed Fdac of 800 MS/S

with Internal PLL)

Ch C+

Ch D+

Ch A+

HDMI DIO

Ch A+

DATACLK =

4”SAMPLECLK

SAMPLECLK

Ch B+

Ch B+ AD9653

QUAD 16-bit

125 MSPS ADC

(Clock at 100 MS/S)

Ch C+

Ch D+

Ch A1

Ch B0

Ch B1

Ch C0

Ch C1

Ch D0

Ch D1

A(15) A(13) A(11) A(9) Ch A0

A(14) A(12) A(10) A(8)

Typ: 4.6 W

Abs Max: 5.5 W

RSS Max: 5.3 W

+/– 4.5 V

+ 1.8 AVDD

+ 1.2 V

+ 3.8 V

+ 3.3 AVDD+ 1.8 DVDD

Inrush Limiter

400 MHz DDR (800 Mb/S)

DIO

16 BIT LVDS 400 MHz DDR (800 Mb/S)

400 MHz DDR (800 Mb/S)

FLEXRIO

SIGNAL REQ

ADC = 25

DAC = 50

PLL = 10

DIO? = 16

TOTAL = 103

+ 12 V

+ 3.3 V

OR + Vcco

+ VccoB

+ VccoA

TB_Ref_CLK/PXI_10

GPIO

VccoA = VccoB = Vcco = 2.5 V

Logic Diagram

The following diagram shows the NI 5783 logic layout.

Tabla de contenidos

Otros manuales de Unidad de control de National Instruments

National Instruments

National Instruments NI 9882 Manual de usuario

National Instruments

National Instruments NI-9208 Manual de usuario

National Instruments

National Instruments FieldPoint FP-20 Series Manual de usuario

National Instruments

National Instruments PXIe-8238 Manual de usuario

National Instruments

National Instruments SCC-FT01 Manual de usuario

National Instruments

National Instruments 9503 Manual de usuario

National Instruments

National Instruments sbRIO-9609 Manual de usuario

National Instruments

National Instruments PXIe-8238 Manual de usuario

National Instruments

National Instruments 9477 Manual de usuario

National Instruments

National Instruments SCC-LP Series Manual de usuario

National Instruments

National Instruments NI-9244 Manual de usuario

National Instruments

National Instruments NI 9930 Manual de usuario

National Instruments

National Instruments FlexRIO PXIe-7975R Manual de usuario

National Instruments

National Instruments NI 9411 Manual de usuario

National Instruments

National Instruments SCXI SCXI-1102 Manual de usuario

National Instruments

National Instruments PXIe-5694 Manual de usuario

National Instruments

National Instruments NI 5772R Manual de usuario

National Instruments

National Instruments 9755 Manual de usuario

National Instruments

National Instruments PXIe-4302 Manual de usuario

National Instruments

National Instruments PCIe-7857 Manual de usuario

National Instruments

National Instruments SCC-A10 Manual de usuario

National Instruments

National Instruments FP-CTR-500 Manual de usuario

National Instruments

National Instruments cRIO-9068 Manual de usuario

National Instruments

National Instruments Network Adapter NI PXIe-6672 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario