Moxa Technologies TN-5916 Series Manual de usuario

P/N: 1802059160011

*1802059160011*

TN-5916 Series

Quick Installation Guide

Moxa ToughNet NAT Router

Edition 2.0, February 2017

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The ToughNet TN-5916 is a high performance M12 Layer 3 NAT Router

that supports Layer 3 routing functionality to facilitate the deployment of

applications across networks. The TN-5916 NAT router uses M12 and

other circular connectors to ensure tight, robust connections and

guarantee reliable operation against environmental disturbances, such as

vibration and shock. The TN-5916 NAT router supports isolated power in

the 24 to 110 VDC power input range, allowing the same model to be used

at different sites around the globe, and provides up to 16 Fast Ethernet

M12 ports with 4 bypass relay ports. Furthermore, with a -40 to 75°C

operating temperature and IP54-rated waterproof enclosure, the router

can be deployed in harsh environments. The TN-5916 series Ethernet

routers are compliant with EN 50155/50121-4 requirements, making the

router suitable for a variety of industrial applications.

Package Checklist

Your ToughNet TN-5916 NAT router is shipped with the following items. If

any of these items is missing or damaged, please contact your customer

service representative for assistance.

•1 Moxa ToughNet NAT router

•M12 to DB9 console port cable

•2 protective caps for console and relay output ports

•Panel mounting kit

•CD-ROM with user’s manual, Windows utility, and SNMP MIB file

•Quick installation guide (printed)

•Warranty card

Features

Anti-Vibration Circular Connectors for Robust Links

•M12 D-coding 4-pin female connectors for Fast Ethernet

10/100BaseT(X) ports.

•M12 A-coding 5-pin male connectors for console and relay output.

•M23 6-pin male connector for power input.

Dual Isolated Power Inputs

•24 to 110 VDC (16.8 to 137.5 VDC), isolated.

Designed for Industry-specific Applications

•Bypass relay ensures non-stop data communication in the event the

router stops working due to a power failure.

•EN 50155/50121-3-2 compliant. See specs for details about

compliance with specific parts of the EN 50155 specifications.

•-40 to 75°C operating temperature range.

•IP54, rugged high-strength case.

•Panel mounting or DIN-rail mounting installation capability.

- 3 -

Recommended Optional Accessories

•CBL-M23(FF6P)Open-BK-100-IP67: 1-meter M23 to 6-pin power

cable with IP67-rated female 6-pin M23 connector

•CBL-M12D(MM4P)/RJ45-100 IP67: 1-meter M12-to-RJ45 Cat-5E UTP

Ethernet cable with IP67-rated male 4-pin M12 D-coded connector

•CBL-M12(FF5P)/OPEN-100 IP67: 1-meter M12-to-5-pin power cable

with IP67-rated female 5-pin M12 A-coded connector

•M12D-4P-IP68: Field-installable M12 D-coded screw-in connector,

male 4-pin, IP68-rated

•M12A-5P-IP68: Field-installable M12 A-coded screw-in connector,

female 5-pin, IP68-rated

•CAP-M12F-M: Metal cap for M12 female connector

•DK-DC50131: DIN-rail mounting kit, 50 x 131 mm

- 4 -

TN-5916 Panel Layouts

1. Model name

2. Screw holes for panel mounting kit

3. Console port

4. Grounding screw

5. Relay output port

6. Power input voltage range indicator

7. Power input port (male 6-pin shielded M23 connector)

8. PWR1 LED: for power input 1

9. PWR2 LED: for power input 2

10.

FAULT LED

11.

MSTR/HEAD LED: for ring master or chain head

12.

CPLR/TAIL LED: for ring coupler or chain tail

13.

TP port’s 10/100 Mbps LED

14.

10/100BaseT(X) port (female 4-

pin shielded M12 connector with D

coding)

15.

Waterproof vent

16.

Product label

17.

12 screw holes for DIN-rail mounting kit

18.

E2 LED: Not used by the TN-5916 series

19.

E1 LED: Not used by the TN-5916 series

20. Ports 9-10, 13-14 with relay bypass function

- 5 -

ATTENTION

DO NOT open or remove the vent (#15). Removing the seal will

invalidate the

warranty.

Ports (including 3, 5, and 14) that are not in use must be tightly

covered with protective caps (an optional accessory) to ensure

IP54/IP67

-rated protection.

Mounting Dimensions (unit = mm)

TN-5916 Series

- 6 -

Panel/Wall Mounting

STEP 1:

Mounting the TN-5916 to a wall requires 4 screws. Use the ToughNet

router as a guide to mark the correct positions of the 4 screws.

STEP 2:

se the 4 screws in the panel

mounting kit. If you would like to

use your own screws, make sure

the screw head

is between 6.0

mm and 7.0 mm in diameter and

the shaft

is less than 4.0 mm in

diameter, as shown

at the right.

Do not screw the screws in all the way—leave a space of about 2 mm to

allow room for sliding the ToughNet router between the wall and the

screws.

NOTE

Before tightening the screws into the wall, make sure the screw

head and shaft size are suitable by inserting the screw through

one of the keyhole-shaped apertures of the ToughNet router.

STEP 3:

Once the screws are fixed in the wall, hang the ToughNet router on the 4

screws through the large opening of the keyhole-shaped apertures, and

then slide the router downwards. Tighten the four screws for added

stability.

NOTE

To provide greater protection from vibration and shock, use

screws with shaft diameter between 6.0 mm and 7.0 mm, and fix

the ToughNet

router onto the wall directly through the large

opening of the keyhole-shaped apertures.

DIN-Rail Mounting (optional)

Use the optional DIN-rail mounting

kit

(DK-DC50131, must be

purchased separately)

mount the

-5916 on a 35 mm DIN-rail.

STEP 1:

Use 12 screws (6 screws per plate)

to attach the two DIN

-rail

attachment plates to the rear panel

of the

router.

- 7 -

STEP 2:

If the spring-loaded bracket is locked in place, push the recessed button

to release it. Once released, you should feel some resistance from the

spring as you slide the bracket up and down a few millimeters in each

direction.

STEP 3:

Position the ToughNet

router

on the

DIN

-rail, tilted, so the clamps hook

over the top edge of the rail.

STEP 4:

Swing the router down fully onto

the DIN-rail, until both clamps

completely latch.

To remove the Moxa ToughNet Router from the DIN-rail, use a

screwdriver to pull out the two spring-loaded brackets from the bottom

until they are fixed in a “locked” position. Then, reverse Steps 3 and 4

above.

Wiring Requirements

WARNING

Turn the power off before disconnecting modules or wires. The

correct power supply voltage is listed on the product label. Check

the voltage of your power source to make sure you are using the

correct voltage. Do NOT use a voltage greater than what is

specified on the product label.

These devices must be supplied by a SELV source as defined in

the Low Voltage Directive 2006/95/EC and 2004/108/EC.

- 8 -

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa

router.

This device has UL

508 approval. Use copper conductors only,

to 75°C

, and tighten to 4.5 inch-pounds. For use in pollution

degree 2 environments.

ATTENTION

Safety First!

Observe all electrical codes dictating the

maximum current

allowable for each wire size. If the current

goes above the

maximum ratings, the wiring could overheat,

causing serious

damage to your equipment.

Please Read and Follow These Guidelines:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring that shares similar electrical characteristics can be

bundled together.

•Keep input wiring and output wiring separated.

•It is strongly advised that you label wiring for all devices in the system

when necessary.

Grounding the ToughNet NAT Router

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

grounding screw to the grounding surface prior to connecting devices.

- 9 -

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface such as a metal panel.

Connecting the Power Supplies

The ToughNet TN-5916 series routers support two sets of power

supplies—power input 1 and power input 2. The M23 6-pin male

connector on the TN-5916’s front panel is used for the dual power inputs.

Pinouts for the Power Input Port on the TN-5916

Description

Usage

1 PWR1 Live / DC +

Connect “PWR1 Live / DC +” to the

positive (+) terminal when using a DC

power source.

2 PWR1 Neutral / DC -

Connect “PWR1 Neutral / DC –” to the

negative (-) terminal when using a DC

power source.

3 Chassis Ground

Connect the “Chassis Ground” to the

safety ground terminal for DC inputs.

4 PWR2 Neutral / DC -

Connect “PWR2 Neutral / DC –” to the

negative (-) terminal when using a DC

power source.

5 PWR2 Live / DC +

Connect “PWR2 Live / DC +” to the

positive (+) terminal when using a DC

power source.

STEP 1:

Plug the power cord connector into the TN-5916’s power input port.

STEP 2:

Screw in the nut on the power cord connector to the power input

connector (on the router) to ensure a tight connection.

ATTENTION

Before connecting the TN

5916 to the power input, make sure the

power source voltage is stable.

- 10 -

Connecting the Relay Outputs

Each TN-5916 router has two sets of relay outputs—relay output 1 and

relay output 2.The M12 A-coded 5-pin male connector on the TN-5916

front panel is used for the two relay outputs. Use a power cord with an

M12 A-coded 5-pin female connector to connect the relay contacts. You

can purchase an M12 power cable from Moxa; the model number is

CBL-M12 (FF5P)/OPEN-100 IP67.

Pinouts for the TN-5916’s Relay Output Port

N.C.: Not connected

FAULT:

The two sets of relay contacts of the M12 A-coded 5-pin male connector

are used to detect user-configured events. The two wires attached to the

fault contacts form an open circuit when a user-configured event is

triggered. If a user-configured event does not occur, the fault circuit

remains closed.

Connecting the Data Lines

10/100BaseT(X) Ethernet Port Connection

All TN-5916 models have 16 10/100BaseT(X) Ethernet ports (4-pin

shielded M12 connector with D coding). The 10/100TX ports located on

the TN-5916 front panel are used to connect to Ethernet-enabled devices.

Most users configure these ports for Auto MDI/MDI-X mode, in which case

the port’s pinouts are adjusted automatically depending on the type of

Ethernet cable used (straight-through or cross-over), and the type of

device (NIC-type or HUB/Switch/Router-type) connected to the port.

In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch/Router-type) ports. We also give cable wiring diagrams for

straight-through and cross-over Ethernet cables.

10/100BaseT(X) Port Pinouts

Housing: shield

Tabla de contenidos

Otros manuales de Enrutador de red de Moxa Technologies

Moxa Technologies

Moxa Technologies EtherDevice EDR-G902-T Manual de usuario

Moxa Technologies

Moxa Technologies OnCell 5004-HSPA Manual de usuario

Moxa Technologies

Moxa Technologies MAR-2000 Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205A-4PoE Manual

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E1210 Manual de usuario

Moxa Technologies

Moxa Technologies EDS-305-M12 Manual

Moxa Technologies

Moxa Technologies Managed Ethernet Switch/Extender Manual de usuario

Moxa Technologies

Moxa Technologies EDS-G308 Manual

Moxa Technologies

Moxa Technologies EtherDevice EDR-G902 Manual

Moxa Technologies

Moxa Technologies E Series Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E2200Series Manual de usuario

Moxa Technologies

Moxa Technologies EDR-G9010 Series Manual de usuario

Moxa Technologies

Moxa Technologies ETHERDEVICE EDS-308 Manual

Moxa Technologies

Moxa Technologies ToughNet Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E1200 Series Manual de usuario

Moxa Technologies

Moxa Technologies NSwitch Manual de usuario

Moxa Technologies

Moxa Technologies EDR-810 Series Manual

Moxa Technologies

Moxa Technologies UC-8112-LX-STK Manual de usuario

Moxa Technologies

Moxa Technologies ToughNet TN-5516 Series Manual

Moxa Technologies

Moxa Technologies PowerTrans PT-7728 Manual

Moxa Technologies

Moxa Technologies EtherDevice Switch EDS-G205 Manual

Moxa Technologies

Moxa Technologies PT-7528 Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-508 Manual

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad