Moxa Technologies EtherDevice EDS-P506A-4PoE Series Manual

Moxa EtherDevice™ Switch

EDS-P506A-4PoE Series

Hardware Installation Guide

First Edition, July 2010

Reproduction without permission is prohibited.

P/N: 1802005060010

—1 —

Overview

The Moxa EtherDevice™ EDS-P506A-4PoE Series Ethernet switches are

managed redundant Ethernet switches that come standard with 4

10/100BaseT(X) 802.3at/af (PoE/PoE+) compliant Ethernet ports, and 1 or 2

10/100BaseT(X) Ethernet ports or 1 or 2 100BaseFX (SC/ST-type connector)

fiber ports. The EDS-P506A-4PoE Ethernet switches provide up to 30 watts

of power per PoE port, and allow power to be supplied to connected devices

(such as surveillance cameras, wireless access points, and IP phones) when

power is not readily available or cost-prohibitive to provide locally. The

EDS-P506A-4PoE Ethernet switches are highly versatile, and their fiber ports

can transmit data up to 40 km from the device to the control center with high

EMI immunity. The Ethernet switches support a variety of management

functions, including Turbo Chain, IEEE 1588 PTP, Turbo Ring, RSTP/STP,

IGMP, VLAN, QoS, RMON, bandwidth management, and port mirroring.

The EDS-P506A-4PoE series is designed especially for security automation

applications such as IP surveillance and gate of entry systems, which can

benefit from a scalable backbone construction and Power-over-Ethernet

support.

The EDS-P506A-4PoE can operate from 0 to 60°C or -40 to 75°C for T

models and are designed to withstand a high degree of vibration and shock.

The rugged hardware design makes the EDS-P506A-4PoE Series perfect for

ensuring that your Ethernet equipment can operate in critical industrial

environments, and complies with FCC and CE standards.

NOTE Throughout this Hardware Installation Guide, we use EDS as an

abbreviation for Moxa EtherDevice Switch.

EDS = Moxa EtherDevice Switch

Package Checklist

The EDS-P506A-4PoE is shipped with the following items. If any of these

items are missing or damaged, please contact your customer service

representative for assistance.

y1 EDS-P506A-4PoE EtherDevice Switch

yHardware Installation Guide (this guide)

yCD-ROM with user’s manual and Windows utility

yMoxa product warranty statement

yRJ45 to DB9 console port cable

yProtective caps for unused ports

yDIN-Rail mounting kit (attached to the EDS-P506A-4PoE’s rear panel by

default)

—2 —

EDS-P506A-4PoE Panel Views

(standard type)

EDS-P506-4PoE

Front Panel View

MSTR/

HEAD

CPLR/

TAI L

RS-232 CONSOLE

------

OFF

MASTER

COUPLER

TURBO

RING

PWR1

PWR2

RELAY2

RELAY1

DI1

DI2

V2-

V2+

Top Panel View

Rear Panel View

1. Grounding screw

2. Terminal block for power input

PWR1/PWR2 and relay output

3. Heat dissipation orifices

4. Console port

5. DIP switches

6. Power input PWR1 LED

7. Power input PWR2 LED

8. Fault LED

9. MSTR/HEAD LED indicator

10. CPLR/TAIL LED indicator

11. Turbo Chain logo

12. TP port’s 100 Mbps LED

13. TP port’s 10 Mbps LED

14. Model Name

15. 10/100 BaseT(X) PoE Ports

16. 10/100 BaseT(X) Ports

17. Screw hole for wall mounting

kit

18. DIN-Rail kit

19. PoE LEDs

—3 —

EDS-P506A-4PoE Panel Views

(SC-type)

EDS-P506A-4PoE-MM-SC

EDS-P506A-4PoE-SS-SC

Front Panel View

RS-232 CONSOLE

------

OFF

MASTER

COUPLER

TURBO

RING

PWR1

PWR2

RELAY2

RELAY1

DI1

DI2

V2-

V2+

Top Panel View

Rear Panel View

1. Grounding screw

2. Terminal block for power

input PWR1/PWR2 and relay

output

3. Heat dissipation orifices

4. Console port

5. DIP switches

6. Power input PWR1 LED

7. Power input PWR2 LED

8. Fault LED

9. MSTR/HEAD LED indicator

10. CPLR/TAIL LED indicator

11. Turbo Chain logo

12. TP port’s 100 Mbps LED

13. TP port’s 10 Mbps LED

14. Model Name

15. 10/100 BaseT(X) PoE Ports

16. 100BaseFX ports

17. FX port’s 100 Mbps LEDs

18. Screw hole for wall mounting

kit

19. DIN-Rail kit

20. PoE LEDs

—4 —

EDS-P506A-4PoE Panel Views

(ST-type)

EDS-P506A-4PoE-MM-ST

Front Panel View

RS-232 CONSOLE

------

OFF

MASTER

COUPLER

TURBO

RING

PWR1

PWR2

RELAY2

RELAY1

DI1

DI2

V2-

V2+

Top Panel View

Rear Panel View

1. Grounding screw

2. Terminal block for power

input PWR1/PWR2 and relay

output

3. Heat dissipation orifices

4. Console port

5. DIP switches

6. Power input PWR1 LED

7. Power input PWR2 LED

8. Fault LED

9. MSTR/HEAD LED indicator

10. CPLR/TAIL LED indicator

11. Turbo Chain logo

12. TP port’s 100 Mbps LED

13. TP port’s 10 Mbps LED

14. Model Name

15. 10/100 BaseT(X) PoE Ports

16. 100BaseFX ports

17. FX port’s 100 Mbps LEDs

18. Screw hole for wall mounting

kit

19. DIN-Rail kit

20. PoE LEDs

—5 —

Mounting Dimensions

30mm(1.18in)

9.75mm(0.38in)

15mm(0.59in)

131.5mm(5.18in) 80.05mm(3.15in)

135mm(5.31in)

70mm(2.76in)

30.5mm(1.2in)

34mm(1.34in)

51.6mm(2.03in)

48.39mm(1.9in)

67mm(2.64in)

14.6mm(0.57in) 20mm(0.79in) 36.6mm(1.44in) 29.5mm(1.16in) 20mm(0.79in) 14.3mm(0.56in)

Side View

DlN-Rail Kit

Front View

Rear View

DlN-Rail Kit

Wall Mounting Kit

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be fixed to the back

panel of the EDS-P506A-4PoE when you take it out of the box. If you need

to reattach the DIN-Rail attachment plate to the EDS-P506A-4PoE, make

sure the stiff metal spring is situated towards the top, as shown by the

following figures.

STEP 1—Insert the top of the

DIN-Rail into the slot just below the

stiff metal spring.

STEP 2—The DIN-Rail attachment

unit will snap into place as shown in

the following illustration.

metal

spring

DIN-Rail

metal

spring

DIN-Rail

To remove the EDS-P506A-4PoE from the DIN-Rail, simply reverse Steps 1

and 2 above.

—6 —

Wall Mounting (Optional)

For some applications, you will find it convenient to mount the Moxa

EDS-P506A-4PoE on the wall, as shown in the following illustrations:

STEP 1—Remove the

aluminum DIN-Rail

attachment plate from the rear

anel of the

EDS-P506A-4PoE, and then

attach the wall mount plates

with M3 screws, as shown in

the figure to the right.



STEP 2—Mounting the EDS-P506A-4PoE on the wall requires 4

screws. Use the EDS-P506A-4PoE, with wall mount plates

attached, as a guide to mark the correct locations of the 6 screws.

The heads of the screws should be less than 6.0 mm in diameter,

and the shafts should be less than 3.5 mm in diameter, as shown

in the figure to the right.

6.0 mm

3.5 mm

NOTE Before tightening the screws into the wall, make sure the screw

head and shank size are suitable by inserting the screw through

one of the keyhole-shaped apertures of the Wall Mounting Plates.

Do not screw the screws in all the

way—leave about 2 mm to allow

room for sliding the wall mount

anel between the wall and the

screws.

STEP 3—Once the screws are fixed

to the wall, insert the four screw

heads through the wide parts of the

keyhole-shaped apertures, and then

slide the EDS-P506A-4PoE

downwards, as indicated in the

figure at the right. Tighten the four

screws for more stability.

MSTR/

HEAD

CPLR/

TAIL

MSTR/

HEAD

CPLR/

TAIL

—7 —

Wiring Requirements

WARNING

Do not disconnect modules or wires unless power has been

switched off or the area is known to be non-hazardous. The

devices may only be connected to the supply voltage shown on

the type plate. The devices are designed for operation with a

Safety Extra-Low Voltage. Thus, they may only be connected to

the supply voltage connections and to the signal contact with the

Safety Extra-Low Voltages (SELV) in compliance with

IEC60950-1/EN60950-1.

ATTENTION

This unit is a built-in type. When the unit is installed in another

piece of equipment, the equipment enclosing the unit must

comply with fire enclosure regulation IEC60950-1/EN60950-1

(or similar regulation).

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa EtherDevice Switch.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

Read and follow these guidelines:

yUse separate paths to route wiring for power and devices. If power wiring

and device wiring paths must cross, make sure the wires are perpendicular

at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

yYou can use the type of signal transmitted through a wire to determine

which wires should be kept separate. The rule of thumb is that wiring that

shares similar electrical characteristics can be bundled together.

yYou should separate input wiring from output wiring.

yWe advise that you label the wiring to all devices in the system.

—8 —

Grounding the Moxa EDS-P506A-4PoE

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well-grounded

mounting surface such as a metal panel.

Wiring the Relay Contact

The EDS-P506A-4PoE has two sets of relay outputs—relay 1 and relay 2.

Each relay contact uses two contacts of the terminal block on the

EDS-P506A-4PoE’s top panel. Refer to the next section for detailed

instructions on how to connect the wires to the terminal block connector, and

how to attach the terminal block connector to the terminal block receptor.

In this section, we illustrate the meaning of the two contacts used to connect

the relay contact.

RELAY1

RELAY2

FAULT:

The two sets of relay contacts of the

6-pin terminal block connector are

used to detect user-configured

events. The two wires attached to

the fault contacts form an open

circuit when a user-configured

event is triggered. If a

user-configured event does not

occur, the fault circuit remains

closed.

Wiring the Redundant Power Inputs

The EDS-P506A-4PoE has two sets of power inputs—power input 1 and

power input 2. The top two contacts and the bottom two contacts of the 6-pin

terminal block connector on the EDS-P506A-4PoE’s top panel are used for

the two digital inputs. The top and front views of one of the terminal block

connectors are shown here.

PWR1 PWR2

V1- V1+

PWR1

V2- V2+

PWR2

V1- V1+ V2- V2+

STEP 1: Insert the

negative/positive DC wires into the

V-/V+ terminals, respectively.

STEP 2: To keep the DC wires

from pulling loose, use a small

flat-blade screwdriver to tighten the

wire-clamp screws on the front of

the terminal block connector.

STEP 3: Insert the plastic terminal

block connector prongs into the

terminal block receptor, which is

located on the EDS-P506A-4PoE’s

top panel.

—9 —

Wiring the Digital Inputs

The EDS-P506A-4PoE has two sets of digital inputs, DI 1 and DI 2. Each DI

consists of two contacts of the 6-pin terminal block connector on the

EDS-P506A-4PoE’s top panel, which are used for the two DC inputs. The top

and front views of one of the terminal block connectors are shown here.

D2I

D1I

I1I2

D2ID1I

STEP 1: Insert the negative

(ground)/positive DI wires into the

┴/I1 terminals, respectively.

STEP 2: To keep the DI wires from

pulling loose, use a small flat-blade

screwdriver to tighten the

wire-clamp screws on the front of

the terminal block connector.

STEP 3: Insert the plastic terminal

block connector prongs into the

terminal block receptor, which is

located on the EDS-P506A-4PoE’s

top panel.

Turbo Ring DIP Switch Settings

EDS-P506A-4PoE switches are plug-and-play managed redundant Ethernet

switches. The proprietary Turbo Ring protocol was developed by Moxa to

provide better network reliability and faster recovery time. Moxa Turbo Ring’s

recovery time is less than 300 ms (Turbo Ring) or 20 ms (Turbo Ring

V2) —compared to a 3- to 5-minute recovery time for commercial

switches—decreasing the possible loss caused by network failures in an

industrial setting.

There are 4 Hardware DIP Switches for Turbo Ring on the top panel of

EDS-P506A-4PoE that can help setup the Turbo Ring easily within seconds. If

you do not want to use a hardware DIP switch to setup the Turbo Ring, you can

use a web browser, telnet, or console to disable this function.

NOTE Refer to the Turbo Ring DIP Switch section and Using

Communication Redundancy section in the User’s Manual for

detailed information about the settings and usage of Turbo Ring

and Turbo Ring V2.

EDS-P506A-4PoE Series DIP Switches

------

MASTER

COUPLER

TURBO

RING

The default setting for each DIP Switch is OFF. The

following table explains the effect of setting the DIP

Switch to the ON position.

Otros manuales para EtherDevice EDS-P506A-4PoE Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de Moxa Technologies

Moxa Technologies

Moxa Technologies ioLogik E1242 Manual de usuario

Moxa Technologies

Moxa Technologies NPort IA5150 series Manual de usuario

Moxa Technologies

Moxa Technologies NAT-102 Series Manual de usuario

Moxa Technologies

Moxa Technologies ToughNet Manual de usuario

Moxa Technologies

Moxa Technologies EDR-810 Series Manual

Moxa Technologies

Moxa Technologies EDR-8010 Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice Switch EDS-G205 Manual

Moxa Technologies

Moxa Technologies TSN-G5000 Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Manual de usuario

Moxa Technologies

Moxa Technologies OnCell G4302-LTE4 Series Manual de usuario

Moxa Technologies

Moxa Technologies TN-5916 Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-1137C-EU Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E1210 Manual de usuario

Moxa Technologies

Moxa Technologies E Series Manual de usuario

Moxa Technologies

Moxa Technologies IKS-6324 Series Manual

Moxa Technologies

Moxa Technologies OnCell 5004 Series Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E2200Series Manual de usuario

Moxa Technologies

Moxa Technologies EDS-408A Manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-508 Manual

Moxa Technologies

Moxa Technologies EDS-518E Manual de usuario

Moxa Technologies

Moxa Technologies SDS-3008 Series Manual de usuario

Moxa Technologies

Moxa Technologies EDS-505A Series Manual de usuario

Moxa Technologies

Moxa Technologies EDS-305-M12 Manual

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad