Moxa Technologies TN-4900 Series Manual de usuario

P/N: 1802049080010

*1802049080010*

TN-4900 Series

Quick Installation Guide

Moxa ToughNet Router

Version 1.0, March 2021

Technical Support Contact Information

www.moxa.com/support



- 2 -

Overview

The ToughNet TN-4900 Series is designed for rolling stock Ethernet

networks. These routers feature M12 interfaces to ensure tight, robust

connections, and guarantee reliable operation in industrial environments

where vibration and shock are commonplace. The TN-4900 Series routers

are equipped with 8 Gigabit ports and up to 4 bypass relay ports. In

addition, the PoE models in this Series have 4 IEEE 802.3at/af PoE Gigabit

ports while the 16-port models have 8 PoE-capable Fast Ethernet ports.

These routers also feature firewall, ETBN, routing functionality, and a

broad power input range of 24 to 110 VDC to facilitate different

applications across networks. The -40 to 70°C wide temperature range

allows the TN-4900 Series to operate in demanding environmental

conditions for extended periods of time. Furthermore, these routers are

compliant with the mandatory requirements of EN 50155, making them

suitable for a variety of industrial applications.

Package Checklist

Your ToughNet TN-4900 router is shipped with the following items. If any

of these items are missing or damaged, please contact your customer

service representative for assistance.

•TN-4900 router

•Protective caps for the console port (x1), Ethernet ports (TN-4908:

x4, TN-4916: x8), and USB storage port (x1)

•Panel mounting kit

•Quick installation guide (printed)

•Warranty card

Features

Anti-Vibration Push-Pull/Circular Connectors for Robust Links

•M12 D-coded 4-pin female connectors for Fast Ethernet

10/100BaseT(X) ports

•M12 X-coded 8-pin female connectors for Gigabit Ethernet

10/100/1000BaseT(X) ports

•M12 B-coded 5-pin female connector for serial console port

•M12 A-coded 5-pin female connector for USB storage port

•M12 K-coded 5-pin male connector for power input

Isolated Power Inputs

•Supports 24 to 110 VDC (16.8 to 137.5 VDC)

High-performance Network Switching Technology

•Provides up to 30 watts per PoE port with a total power budget of 50

watts per router for TN-4908 PoE models and 95 watts per router for

TN-4916 PoE models

•IPv6 Ready logo awarded (IPv6 Logo Committee certified)

•DHCP Option 82 for IP address assignment with different policies

•Turbo Ring and Turbo Chain (recovery time < 50 ms @ 250 routers),

and STP/RSTP/MSTP for network redundancy

•IGMP snooping and GMRP for filtering multicast traffic

•EtherNet/IP and Modbus/TCP industrial Ethernet protocols supported

•Port-based VLAN, IEEE 802.1Q VLAN, and GVRP to ease network

planning

- 3 -

•QoS (IEEE 802.1p/1Q and ToS/DiffServ) allows real-time traffic

classification and prioritization

•SNMPv1/v2c/v3 for different levels of network management

•RADIUS, SNMPv3, IEEE 802.1X, HTTPS, and SSH to enhance network

security

•RMON for efficient network monitoring and proactive capability

•Bandwidth management prevents unpredictable network status

•Port mirroring for online debugging

•Automatic warning by exception through email

•Line-swap fast recovery

•LLDP for automatic topology discovery in network management

software

•Configurable by web browser, Telnet/serial console, CLI, and

Windows utility

Designed for Industry-Specific Applications

•Eight Gigabit Ethernet ports to meet high bandwidth requirements.

•Complies with all EN 50155 mandatory test items*

•-40 to 70°C operating temperature range

•IP42-rated rugged high-strength case

•Panel mounting installation capability

*This product is suitable for rolling stock railway applications, as defined

by the EN 50155 standard. For a more detailed statement, click here:

www.moxa.com/doc/specs/EN_50155_Compliance.pdf

Recommended Optional Accessories

•CBL-M12XMM8PRJ45-Y-200-IP67: 2-meter M12-to-RJ45 Cat-5 UTP

Ethernet cable with IP67-rated 8-pin male X-coded crimp type M12

connector

•CBL-M12XMM8P-Y-300-IP67: 3-meter M12-to-M12 Cat-5 UTP

Ethernet cable with IP67-rated 8-pin male X-coded crimp type M12

connector

•CBL-M12XMM8P-Y-100-IP67: 1-meter M12-to-M12 Cat-5 UTP

Ethernet cable with IP67-rated 8-pin male X-coded crimp type M12

connector

•M12X-8PMM-IP67-HTG: Field-installable M12 X-coded crimp type,

slim design connector, 8-pin male, IP67-rated

•A-CAP-M12F-M-PP: Metal Cap for M12 female push-pull connector

•CBL-M12D(MM4P)/RJ45-100 IP67: 1-meter M12-to-RJ45 Cat-5E UTP

Ethernet cable with IP67-rated male 4-pin M12 D-coded connector

•M12D-4P-IP68: Field-installable M12 D-coded screw-type connector,

male 4-pin, IP68-rated

- 4 -

Panel Layouts

TN-4908 Models

1. Screw holes for panel

mounting kit

2. Console port

3. USB port

4. FAULT LED

5. PWR1 LED:

for power input 1

6. PWR2 LED:

for power input 2

10/100/1000BaseT(X) port

(M12 X-coded 8-

pin female

connector)

10/100/1000BaseT(X) port

LED

9. PoE LED

10.

Grounding screw

11.

Power input port (M12

K-coded 5-pin male

connector)

12.

CPLR/TAIL LED: for ring

coupler or chain tail

13.

MSTR/HEAD LED: for ring

master or chain head

14.

Alignment mark for

X-coded connector

- 5 -

TN-4916 Models

1. Screw holes for panel

mounting kit

2. Console port

3. USB port

4. FAULT LED

5. PWR1 LED:

for power input 1

6. PWR2 LED:

for power input 2

10/100/1000BaseT(X) port

(M12 X-coded 8-

pin female

connector)

10/100/1000BaseT(X) port

LED

9. PoE LED

10.

Grounding screw

11.

Power input port (M12

K-coded 5-pin male

connector)

12.

CPLR/TAIL LED: for ring

coupler or chain tail

13.

MSTR/HEAD LED: for ring

master or chain head

14.

Alignment mark for

X-coded connector

ATTENTION

Exposed connectors when not in use must be tightly covered with

protective caps

(an optional accessory) to ensure IP67-rated

protection.

- 6 -

Mounting Dimensions (unit = mm)

TN-4908 PoE Models

- 7 -

TN-4908 Non-PoE Models

- 8 -

TN-4916 PoE Models

- 9 -

Panel/Wall Mounting

STEP 1: Mounting the TN-4900 to a wall requires 4 screws. Use the

ToughNet router as a guide to mark the correct positions of the 4 screws.

STEP 2: Use the 4 screws in the

panel mounting kit. If you would like

to use your own screws, make sure

the screw head

between 6.0 mm

and 7.0 mm

in diameter and the

shaft

is less than 4.0 mm in

diameter, as shown

at the right.

The torque value of the mounting

screws is 4.5 kgf-cm.

Do not screw the screws in all the way—leave a space of about 2 mm to

allow room for sliding the ToughNet router between the wall and the

screws.

NOTE

Before tightening the screws into the wall, make sure the screw

head and shaft size are suitable by inserting the screw through

one of the keyhole-shaped apertures of the ToughNet router.

STEP 3: Once the screws are fixed in the wall, hang the ToughNet router

on the 4 screws through the large opening of the keyhole-shaped

apertures, and then slide the router downwards. Tighten the four screws

for added stability.

NOTE

To provide greater protection from vibration and shock, use

screws with shaft diameter between 6.0 mm and 7.0 mm, and fix

the ToughNet

router onto the wall directly through the large

opening of the keyhole-shaped apertures.

Wiring Requirements

WARNING

Turn the power off before disconnecting modules or wires. The

correct power supply voltage is listed on the product label. Check

the voltage of your power source to make sure you are using the

correct voltage. Do NOT

use a voltage greater than what is

specified on the product label.

These devices must be supplied by a SELV source as defined in

the Low Voltage Directive 2006/95/EC and 2004/108/EC.

- 10 -

ATTENTION

Safety First!

Be sure to

disconnect the power cord before installing and/or

wiring your Moxa

router. This device has UL 61010-2-201

approval. Use copper conductors only,

°C, and tighten to 4.5

pound-inches. For use in pollution degree 2 environments.

ATTENTION

Safety First!

Observe all electrical codes dictating the

maximum current

allowable for each wire size. If the current

goes above the

maximum ratings, the wiring could overheat,

causing serious

damage to your equipment.

Please read and follow these guidelines:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring that shares similar electrical characteristics can be

bundled together.

•Keep input wiring and output wiring separated.

•It is strongly advised that you label wiring for all devices in the system

when necessary.

Grounding the ToughNet Router

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

grounding screw to the grounding surface prior to connecting devices.

Tabla de contenidos

Otros manuales de Enrutador de red de Moxa Technologies

Moxa Technologies

Moxa Technologies EDS-408A Manual

Moxa Technologies

Moxa Technologies EDS-305-M12 Manual

Moxa Technologies

Moxa Technologies EtherDevice EDR-G902 Manual

Moxa Technologies

Moxa Technologies EDS-518E Manual de usuario

Moxa Technologies

Moxa Technologies NPort 5000 Series Manual de usuario

Moxa Technologies

Moxa Technologies OnCell 5004 Series Manual de usuario

Moxa Technologies

Moxa Technologies ToughNet TN-5308-4 Manual

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Manual de usuario

Moxa Technologies

Moxa Technologies PT-7528 Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Manual de usuario

Moxa Technologies

Moxa Technologies IKS-6324 Series Manual

Moxa Technologies

Moxa Technologies NPort IA5150 series Manual de usuario

Moxa Technologies

Moxa Technologies EDR-G9010 Series Manual de usuario

Moxa Technologies

Moxa Technologies TN-5916 Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Manual de usuario

Moxa Technologies

Moxa Technologies OnCell G4302-LTE4 Series Manual de usuario

Moxa Technologies

Moxa Technologies AWK-4121 Manual de usuario

Moxa Technologies

Moxa Technologies EDS-518E Manual de usuario

Moxa Technologies

Moxa Technologies EDS-405 Manual de usuario

Moxa Technologies

Moxa Technologies EDR-G9010 Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-508 Manual

Moxa Technologies

Moxa Technologies EtherDevice Switch EDS-G205 Manual

Moxa Technologies

Moxa Technologies PowerTrans PT-7728 Manual

Moxa Technologies

Moxa Technologies ioLogik E1242 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad