Moxa Technologies ToughNet TN-5516 Series Manual
Moxa ToughNet Switch
TN-5516/5518 Series
Layer 2 M12 managed 16/16+2G-port Ethernet switches
Hardware Installation Guide
First Edition, October 2009
©2009 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.
P/N: 1802055160011
—1 —
Overview
The ToughNet TN-5516/5518 series M12 managed Ethernet switches are
designed for industrial applications in harsh environments. The TN series
switches use M12 and other circular connectors to ensure tight, robust
connections, and guarantee reliable operation against environmental
disturbances, such as vibration and shock. The wide selection of 12/24/36/48
VDC, 72/96/110 VDC, or 110/220 VDC/VAC dual redundant power supplies
increases the reliability of your communications. The TN-5516 switches
provide up to 16 fast Ethernet M12 ports.
The TN-5518 switches provide up to 16 fast Ethernet M12 ports, and the 2
ports located on the bottom provide a Gigabit Ethernet interface with bypass
relay option. Models with an extended operating temperature range of -40 to
75°C are also available. The TN-5516/5518 series Ethernet switches are
compliant with EN50155/50121-3-2/50121-4 (railway applications), NEMA
TS2 (traffic control systems), and e-Mark (vehicles) requirements, making
the switches suitable for a variety of industrial applications.
Package Checklist
Your ToughNet TN-5516/5518 switch is shipped with the following items. If
any of these items is missing or damaged, please contact your customer
service representative for assistance.
y1 Moxa ToughNet switch.
yHardware installation guide.
yCD-ROM with user’s manual, Windows utility, and SNMP MIB file.
yMoxa product warranty statement.
yM12 to DB9 console port cable.
y2 protective caps for console and relay output ports
yPanel mounting kit.
Features
Anti-Vibration Circular Connectors for Robust Links
yM12 D-coding 4 pins female connectors for Fast Ethernet 10/100BaseT(X)
ports.
yCircular connectors (RJ45-type) for Gigabit Ethernet
10/100/1000BaseT(X) ports
yM12 A-coding 5 pins male connectors for console and relay output.
yM23 5 pins male connector for power input.
Dual, Isolated Redundant Power Inputs
ySupports 12/24/36/48 VDC (8.4–60 VDC).
ySupports 72/110 VDC (50.4–54 VDC), isolated.
ySupports 110/220 VDC/VAC (88–300VDC, 85–264 VAC), isolated.
yDual redundant, parallel load-sharing power supplies.
High Performance Network Switching Technology
yIPv6 ready, certified by the IPv6 Logo Committee.
—2 —
yIEEE 1588 PTP (Precision Time Protocol) for the precise time
synchronization of networks.
yDHCP Option 82 for IP address assignment with different policies.
yModbus/TCP industrial Ethernet protocol.
yTurbo Ring, Turbo Chain,and RSTP/STP (IEEE802.1w/D).
yIGMP Snooping and GMRP for filtering multicast traffic from industrial
Ethernet protocols.
yPort-based VLAN, IEEE802.1Q VLAN, and GVRP protocol to ease
network planning.
yQoS (IEEE802.1p/1Q and TOS/DiffServ) to increase determinism.
y802.3ad, LACP for optimum bandwidth utilization.
yIEEE802.1X and https/SSL to enhance network security.
ySNMP v1/v2c/v3 for different levels of network management.
yRMON for efficient network monitoring and proactive capability.
yBandwidth management prevents unpredictable network status.
yLock port allows access by only authorized MAC addresses.
yPort mirroring for online debugging.
yAutomatic warning by exception through email, relay output.
yAutomatic recovery of connected devices’ IP addresses.
yLine-swap fast recovery.
yLLDP for automatic topology discovery through network management
software.
yConfigurable through Web browser, Telnet/Serial console, and Windows
utility.
Designed for Industry-specific Applications
yTwo Gigabit Ethernet ports to meet high bandwidth requirements.
yBypass relay option on the 2 Gigabit Ethernet ports ensure non-stop data
communication in the event the switch stops working due to a power
failure .
yThree rotary switches for setting the last 3 digits of the IP address makes
maintenance even easier.
yEN 50155/50121-3-2/50121-4, NEMA TS2, and e-Mark compliant.
y-40 to 75°C operating temperature range (for “-T” models).
yIP54/IP67, rugged high-strength case.
yPanel mounting or DIN-Rail mounting installation capability.
Recommended Optional Accessories
yCBL-M23(FF5P)Open-BK-100-IP67: 1-meter M23-to-5-pin power cable
with IP67-rated female 5-pin M23 connector.
yCBL-M12D(MM4P)/RJ45-100 IP67: 1-meter M12-to-RJ45 Cat-5E UTP
Ethernet cable with IP67-rated male 4-pin M12 D-coded connector.
yCBL-M12(FF5P)/OPEN-100 IP67: 1-meter M12-to-5-pin power cable
with IP67-rated female 5-pin M12 A-coded connector.
yM12D-4P-IP68: Field-installable M12 D-coded screw-in connector, male
4-pin, IP68-rated.
—3 —
yM12A-5P-IP68: Field-installable M12 A-coded screw-in connector,
female 5-pin, IP68-rated.
yA-CAP-M12F-MIP67-PAK04: Caps for M12 D-coded 4-pin male
connectors, metal and IP67-rated. Four pieces in one pack.
yDK-DC50131: DIN-Rail mounting kit, 50 x 131 mm.
TN-5516 Panel Layouts
1
22
3
4
5
6
7
8 9 10 11 12
13
14
18
19
15
17
16
17
Top View
Front View
Botton View
Rear View
1. 3 Rotary switches and protective cover with Model name.
2. Screw holes for panel mounting kit.
3. Console port.
4. Grounding screw.
5. Relay output port.
6. Power input voltage range indication.
7. Power input port (male 5-pin shielded M23 connector).
8. PWR1 LED: for power input 1.
9. PWR2 LED: for power input 2.
—4 —
10. FAULT LED.
11. MSTR/HEAD LED: for ring master or chain head.
12. CPLR/TAIL LED: for ring coupler or chain tail.
13. TP port’s 10/100 Mbps LED.
14. 10/100BaseT(X) port (female 4-pin shielded M12 connector with D
coding).
15. Waterproof vent.
16. Product label.
17. 12 Screw holes for DIN-Rail mounting kit.
18. E1 LED: Not used by the TN-5516 series.
19. E2: LED: Not used by the TN-5516 series.
TN-5518 Panel Layouts
1
22
3
4
5
6
7
8 9 10 11 12
13
14
18
19
15
17
16
17
Top View
Front View
Botton View
Rear View
—5 —
1. 3 Rotary switches and protective cover with Model name.
2. Screw holes for panel mounting kit.
3. Console port.
4. Grounding screw.
5. Relay output port.
6. Power input voltage range indication.
7. Power input port (male 5-pin shielded M23 connector).
8. PWR1 LED: for power input 1.
9. PWR2 LED: for power input 2.
10. FAULT LED.
11. MSTR/HEAD LED: for ring master or chain head.
12. CPLR/TAIL LED: for ring coupler or chain tail.
13. TP port’s 10/100 Mbps LED.
14. 10/100BaseT(X) port (female 4-pin shielded M12 connector with D
coding).
15. Waterproof vent.
16. Product label.
17. 12 Screw holes for DIN-Rail mounting kit.
18. E1 LED: Down-side E1 Gigabit port's 10/100/1000 Mbps LED.
19. E2: LED: Down-side E2 Gigabit port's 10/100/1000 Mbps LED.
20. Gigabit Ethernet port E1 (corresponding to port 17 in the TN-5518
User's Manual).
21. Gigabit Ethernet port E2 (corresponding to port 18 in the TN-5518
User's Manual).
ATTENTION
DO NOT open or remove the vent (#15). Once the seal has
been removed, the warranty becomes invalid.
Exposed connectors (including 3, 5, and 14) when not in use
must be tightly covered with protective caps (an optional
accessory) to ensure IP54/IP67-rated protection.
After the rotary switches (1) are set, the protective cover must
be properly affixed to ensure IP54/IP67-rated protection.
—6 —
Mounting Dimensions (unit = mm)
TN-5516 Series
—7 —
TN-5518 Series
Panel/Wall Mounting
STEP 1:
Mounting the TN-5516/5518 to a wall requires 4 screws. Use the ToughNet
switch as a guide to mark the correct positions of the 4 screws.
STEP 2:
Use the 4 screws in the panel mounting kit. If you
would like to use your own screws, make sure the
screw head is between 6.0 mm and 7.0 mm in
diameter and the shaft is less than 4.0 mm in diameter,
as shown at the right.
Do not screw the screws in all the way—leave a space
of about 2 mm to allow room for sliding the ToughNet switch between the
wall and the screws.
NOTE Before tightening the screws into the wall, make sure the screw
head and shaft size are suitable by inserting the screw through one
of the keyhole-shaped apertures of the ToughNet switch.
6.0 - 7.0 mm
< 4.0 mm
—8 —
STEP 3:
Once the screws are fixed in the wall, hang the ToughNet switch on the 4
screws through the large opening of the keyhole-shaped apertures, and then
slide the switch downwards. Tighten the four screws for added stability.
NOTE To provide greater protection from vibrations and shocks, use
screws with shaft diameter between 6.0 mm and 7.0 mm, and fix
the ToughNet switch onto the wall directly through the large
opening of the keyhole-shaped apertures.
DIN-Rail Mounting (optional)
With the optional DIN-Rail
mounting kit DK-DC50131 (must
be purchased separately), you can
mount the TN-5516/5518 on a
35mm DIN-Rail.
STEP 1:
Use 12 screws (6 screws per plate)
to attach the two DIN-Rail
attachment plates to the rear panel
of the switch.
Recessed button
Spring-loaded bracket
STEP 2:
If the spring-loaded bracket is locked in place, push the recessed button to
release it. Once released, you should feel some resistance from the spring as
you slide the bracket up and down a few millimeters in each direction.
STEP 3:
Position the ToughNet switch on the
DIN-Rail, tilting to hook clamps over
the top edge of the rail.
STEP 4:
Swing the switch down fully onto
the DIN-Rail, until both clamps
completely latch.
DIN-Rail
DIN-Rail
—9 —
To remove the Moxa ToughNet Switch from the DIN-Rail, use a screwdriver
to pull out the two spring-loaded brackets from the bottom until they are fixed
in the “locked” position. Then reverse Step 3 and 4 above.
DIN-Rail
Wiring Requirements
WARNING
Turn the power off before disconnecting modules or wires. The
correct power supply voltage is listed on the product label. Check
the voltage of your power source to make sure you are using the
correct voltage. Do NOT use a voltage greater than what is
specified on the product label.
These devices must be supplied by a SELV source as defined in
the Low Voltage Directive 2006/95/EC and 2004/108/EC.
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa switch.
This device has UL508 approval. Use copper conductors only,
60/75°C, and tighten to 4.5 pound-inches. For use in pollution
degree 2 environments.
ATTENTION
Safety First!
Observe all electrical codes dictating the maximum current
allowable for each wire size. If the current goes above the
maximum ratings, the wiring could overheat, causing serious
damage to your equipment.
Otros manuales para ToughNet TN-5516 Series
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Enrutador de red de Moxa Technologies
Moxa Technologies
Moxa Technologies PT-7528 Manual de usuario
Moxa Technologies
Moxa Technologies NPort IA5150 series Manual de usuario
Moxa Technologies
Moxa Technologies NPort 5000 Series Manual de usuario
Moxa Technologies
Moxa Technologies EDR-8010 Series Manual de usuario
Moxa Technologies
Moxa Technologies EtherDevice EDS-G205A-4PoE Manual
Moxa Technologies
Moxa Technologies IKS-6324 Series Manual
Moxa Technologies
Moxa Technologies EtherDevice EDS-P506A-4PoE Series Manual
Moxa Technologies
Moxa Technologies ioLogik E1200 Series Manual de usuario
Moxa Technologies
Moxa Technologies NSwitch Manual de usuario
Moxa Technologies
Moxa Technologies ioLogik E1210 Manual de usuario
Moxa Technologies
Moxa Technologies EtherDevice EDR-G903 Manual de usuario
Moxa Technologies
Moxa Technologies E Series Manual de usuario
Moxa Technologies
Moxa Technologies ioLogik E1200 Series Manual de usuario
Moxa Technologies
Moxa Technologies EtherDevice Switch EDS-G205 Manual
Moxa Technologies
Moxa Technologies TN-4900 Series Manual de usuario
Moxa Technologies
Moxa Technologies EDS-405 Manual de usuario
Moxa Technologies
Moxa Technologies EtherDevice EDR-G903 Manual de usuario
Moxa Technologies
Moxa Technologies EtherDevice EDS-508 Manual
Moxa Technologies
Moxa Technologies ToughNet Manual de usuario
Moxa Technologies
Moxa Technologies ToughNet TN-5308-4 Manual
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad