Molex 207129 Series Manual de usuario

Hand Crimp Tool 1.25mm (.049”) / 2.00 (.078”) Wire-to-Board Crimp Terminal

oc No: ATS-638253300 Release ate: 06-25-12 UNCONTROLLED COPY Page 1 of 5

Revision: A Revision ate: 06-25-12

INSULATION

CRIMP

BRUSH

STRIP

LENGTH

BELL MOUTH

CRIMP HEIGHT

BEND

DOWN

BEND UP

ROLLING

CONDUCTOR

CRIMP

TWISTING

HAND CRIMP

TOOL

Application Tooling

Specification S eet Order No. 63825-3300

FEATURES

% A full cycle ratcheting hand tool ensures complete crimps

% This tool is designed to be used with reeled product due to the small size of the connector

% This tool is designed for prototype work only and is not designed for production

% The reeled product must be cut into 5-inch strips to be processed in this hand tool

% This tool is IPC/WHMA A-620 Class 2 compliant as indicated

% This tool is RoHS compliant, however RoHS compliant is not required

SCOPE

Products: 1.25mm (.049”) / 2.00 (.078”) Wire-to-Board Crimp Terminal, 28-30 AWG.

Terminal

Series No.

Terminal Order No.

Reel Form Only

Wire Size Insulation Diameter Strip Lengt

IPC/WHMA-A620 (1)

Terminal (2)

AWG mm² mm In. mm In. mm In.

104466 104466-8002 ●28-30

0.08-0.05

0.80-1.00

.032-.039

0.80-1.00

.032-.039

1.40-1.90

.055-.075

1. To achieve optimum IPC-A620 insulation crimps, use this insulation O range.

2. Overall insulation O specification for terminal.

Customer to cut off terminal from reel: 0.15mm (.006”) maximum Cut-off Tab.

● Requires Separate Insulation Punch for 28 and 30 AWG. See Page 6.

DEFINITION OF TERMS

The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the

scope.

TYPE 7

Hand Crimp Tool 1.25mm (.049”) / 2.00 (.078”) Wire-to-Board Crimp Terminal

oc No: ATS-638253300 Release ate: 06-25-12 UNCONTROLLED COPY Page 2 of 5

Revision: A Revision ate: 06-25-12

Insulation Crimp Form

This crimp terminal is designed for miniaturization; therefore, each dimension of insulation crimp portion appears

small as compared to the terminal material thickness. In order to avoid insulation piercing the crimp forms by the

insulation barrel, coining is provided inside of the insulation barrel. For this reason, various crimp forms will occur at

the tip of the insulation crimp barrel shown in the figure below.

These crimp forms maybe changed completely by a small change in the wire, insulation punch, or terminal.

These crimp forms are satisfactory for original function of the insulation crimp portion and it is confirmed that all of

these forms below are acceptable insulation crimps.

CONDITIONS:

After crimping, the conductor profiles should measure the following.

Terminal

Series No

Wire Size Conductor Crimp (Ref) Insulation Crimp (Ref) Pull Force

Minimum

Heig t Widt Heig t Widt

AWG

mm2

mm In. mm In. mm In. mm In. N Lb.

104466 28 0.08 0.55-0.60

.022-.024

0.80

.032

1.15

.045

1.00

.039

9.8 2.20

104466 30 0.05 0.50-0.55

.020-.022

0.80

.032

1.15

.045

1.00

.039

4.9 1.10

OPERATION

CAUTION: Install only Molex terminals listed above with this tool. o not crimp hardened objects as

damage can occur to the tool or die.

Open the tool by squeezing the handles together, at the end of the closing stroke, the ratchet mechanism will

release the handles, and the hand tool will spring open.

Crimping Terminals

1. Select the desired terminal listed in the preceding charts.

2. Cut a strip of the terminals approximately 5.0” off the reel. Position the terminal strip into the slot of the carrier

guide with terminals facing forward.

3. Push the strip in until it locks into the (2) detent in the carrier guide and a terminal is centered with the punch

nest. See Figure 1.

4. Partially close the jaws of the hand tool by squeezing the handles until you hear the fist click of the ratchet.

5. From the top of the hand tool insert the pre-stripped wire into the terminal.

6. Compress the terminal by squeezing the tool handles until the ratchet mechanism cycle has been completed.

Release handles to open the jaws.

Note: The tamper proof ratchet action will not release the tool until it has been fully closed.

7. Lift up the crimped terminal from the terminal locator.

8. Visually inspect the crimped terminal for proper crimp location.

Hand Crimp Tool 1.25mm (.049”) / 2.00 (.078”) Wire-to-Board Crimp Terminal

oc No: ATS-638253300 Release ate: 06-25-12 UNCONTROLLED COPY Page 3 of 5

Revision: A Revision ate: 06-25-12

9. If crimping more wires, advance the

terminal strip by (1) detent until the

terminal is centered with the punch nest.

10. Repeat this procedure until all the desired

terminals are crimped on the strip.

Maintenance

It is recommended that each operator of the

tool be made aware of, and responsible for,

the following maintenance steps:

1. Remove the plastic handles from the

metal tool frame by removing the screws

and remove dust, moisture, and other

contaminants with a clean brush, or soft,

lint free cloth.

2. o not use any abrasive materials that

could damage the tool.

3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine

oil. o not oil excessively. The tool was engineered for durability but like any fine piece of equipment it needs

cleaning and lubrication for a maximum service life of trouble free crimping. Light oil used at the pivot points

every 5,000 crimps or 3 months, will significantly enhance the tool life.

4. Wipe excess oil from hand tool, particularly from crimping area.

5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies,

and store the tool in a clean, dry area.

Miscrimps or Jams

Should this tool ever become stuck or jammed in a partially closed

position, Do Not force the handles open or closed. The tool will open

easily by pressing the ratchet release lever up. See Figure 2.

How to Adjust Tool Preload

It may be necessary over the life of the tool to adjust tool handle

preload force. Listed below are the steps required to adjust the

crimping force of the hand tool to obtain proper crimp conditions:

1. Remove the 2mm locking screw from the numbered adjusting wheel using a screw driver. See Figure 3.

2. Using the same screw driver turn the adjustment wheel to the next highest number.

Note: The uneven numbers are in clockwise (CW) direction and the even numbers are counter clockwise

(CCW).

3. Example: If the preload is set at number 5, then to increase the preload, turn the adjustment wheel until the 6th

position is located over the 2mm locking screw tapped hole. If it is necessary to move to the 7th position, then

the adjustment wheel should be turned counter clockwise (CCW) until the 7th position is over the 2mm locking

screw tapped hole.

SLIDE WIRE

INTO THE

PUNCH NEST

Figure 1

LOCKS IN THE

TERMIAL STRIP SLIDE TERMINAL

STRIP INTO THE

CARRIER GUIDE

CRIMP TOOL OPEN

WIRE

RATCHET

RELEASE LEVER

Figure 2

Hand Crimp Tool 1.25mm (.049”) / 2.00 (.078”) Wire-to-Board Crimp Terminal

oc No: ATS-638253300 Release ate: 06-25-12 UNCONTROLLED COPY Page 4 of 5

Revision: A Revision ate: 06-25-12

NUMBERED ADJUSTMENT

WHEEL

Figure 3 TURN CLOCKWISE (CW) OR

COUNTER CLOCKWISE (CCW)

TO ADJUST THE PRE-LOAD

TURN WITH A SMALL

SCREW DRIVER

REMOVE THE LOCKING 2MM SCREW

4. Replace the 2mm locking screw, aligning the nearest notch in the setting wheel to locking screw.

5. Check the crimp specifications and conduct a pull test after tool handle preload force is adjusted. Repeat

these steps until the desired result is obtained.

Warranty

This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital

components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30

days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will

not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping,

fixturing, or use of handle extensions voids this warranty.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.

CAUTIONS:

1. Manually powered hand tools are intended for low volume, prototyping, or field repair. This tool is NOT

intended for production use. Repetitive use of this tool should be avoided.

2. Insulated rubber handles are not protection against electrical shock.

3. Wear eye protection at all times.

4. Use only the Molex terminals specified for crimping with this tool.

Certification

Molex does not certify or re-certify hand tools but rather supplies the following guidelines for customers to re-certify

hand tools.

% This tool is qualified to pull force only. To re-certify, crimp a terminal to a wire, which has been stripped

12.7mm (1/2”) long, so there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than

25mm (1.00”) per minute. See the Molex web site for the Quality Crimp Handbook for more information on pull

testing.

% If the tool does not meet minimum pull force values, handle preload should be increased and the pull test rerun,

(See How to Adjust Preload).

% When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and

replaced.

Hand Crimp Tool 1.25mm (.049”) / 2.00 (.078”) Wire-to-Board Crimp Terminal

oc No: ATS-638253300 Release ate: 06-25-12 UNCONTROLLED COPY Page 5 of 5

Revision: A Revision ate: 06-25-12

Figure 4

FOR

30 AWG

WIRE

FOR

28 AWG

WIRE

PARTS LIST

Item

Order No Description Use Only Wit Wire AWG Quantity

REF

63825-3300

Hand Crimp Tool --- Figure 4

1 11-11-0320 Spring (Ratchet) All 1

2 63600-0479

Spring (Main) All 1

3 69008-0972

Adjuster Wheel All 1

4 63825-3301

Conductor Punch All 1

5 63825-3302

Insulation Punch (Marked 28)

28 AWG 1

6 63825-3303

Insulation Punch (Marked 30)

30 AWG 1

7 63825-3304

Combination Anvil All 1

8 63825-3305

Carrier Guide All 1

9 63825-3370

28 AWG Wire Tool Kit Includes 1 each of Item No. 4 and 5

10 63825-3380

30 AWG Wire Tool Kit Includes 1 each of Item No. 4 and 6

(3 included with hand tool) 1

Visit our Web site at http://www.molex.com

Otros manuales para 207129 Series

100

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas de crimpado de molex

molex

molex AT-200 Manual

molex

molex 207129 Series Manual de usuario

molex

molex 19294-0008 Manual de usuario

molex

molex 57022 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63827-1600 Manual de usuario

molex

molex 63801-8500 Manual de usuario

molex

molex 64001-1000 Manual de usuario

molex

molex ServiceGrade 64016-0038 Manual de usuario

molex

molex 207129 Series Manual de uso y cuidado

molex

molex 207129 Series Manual de usuario

molex

molex CR1031E Manual de usuario

molex

molex Avikrimp AT 5762 Manual de usuario

molex

molex 63811-2200 Manual de usuario

molex

molex 63825-9570 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 78172 Series Manual de usuario

molex

molex 63823-5100 Guía del usuario

molex

molex 207129 Series Manual de usuario

molex

molex 2002180370 Manual de usuario

molex

molex 63825-0500 Manual de usuario

molex

molex RHT-4754 Manual de usuario

molex

molex 63828-1900 Manual de usuario

molex

molex 63816-0200 Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario