molex 207129 Series Manual de usuario
Hand Crimp Tool for 0.60mm (.027") CP 0.6 Series Crimp Terminals
Doc No: ATS 638119100 Release Date: 02 12 07 UNCONTROLLED COPY Page 1 of 5
Revision: F Revision Date: 11 22 10
CONDUCTOR
BRUSH
STRIP LENGTH
SEAM
CONDUCTOR
CRIMP HEIGHT
CUT-OFF
TAB
BELL MOUTH
BEND UP
TWISTING
ROLLING
BEND
DOWN
WIRE
HAND CRIMP
TOOL
Application Tooling
Sp cification Sh t Ord r No. 63811-9100
FEATURES
A full cycle ratcheting hand tool ensures complete crimps
A precision user friendly terminal locator wire stop holds terminals in the proper crimping position
This tool is WHMA IPCA620 Class 3 only with specified wire types and RoHS compliant
SCOPE
Products: 0.60mm (.027") CP 0.6 Female Crimp Terminal CMC connector 0.22 0.35mm2.
T rminal S ri s No. T rminal Ord r No. Wir Siz Insulation Diam t r Strip L ngth
Availabl in R l form only AWG mm² mm In. mm In.
98913 64322
98913 1019
98913 1229
98913 1329
98913 1349
98913 3019
64322 1019
64322 1229
64322 1329
64322 1349
0.35 1.25 1.40 .049 .055 3.50 .138
0.22 1.15 1.25 .045 .049 3.50 .138
Customer to cut off terminal from reel: 0.30mm (.012”) maximum Cut off Tab.
Note: Terminal will accommodate the thin wall small insulation with the IR or ID type Metric wires.
DEFINITION OF TERMS
TYPE 7
Hand Crimp Tool for 0.60mm (.027") CP 0.6 Series Crimp Terminals
Doc No: ATS 638119100 Release Date: 02 12 07 UNCONTROLLED COPY Page 2 of 5
Revision: F Revision Date: 11 22 10
CRIMP SPECIFICATION
After crimping, the conductor profiles should measure the following, see note.
T rminal S ri s No. Wir Siz Conductor Crimp Insulation Crimp Pull Forc
Minimum Profil
H ight (R f.) H ight (R f.)
AWG
mm2 mm In. mm In. N Lb. ----- 0.22-0.35
98913 0.35 0.70 0.80 .028 .031 1.40 1.55 .055 .061 60.0 13.50
Not in use
X
0.22 0.70 0.80 .028 .031 1.40 1.55 .055 .061 40.0 9.00
Not in use
X
64322 0.35 0.70 0.80 .028 .031 1.40 1.55 .055 .061 60.0 13.50
Not in use
X
0.22 0.70 0.80 .028 .031 1.40 1.55 .055 .061 40.0 9.00
Not in use
X
Not :
A crimp height chart is provided with this manual as Reference Only. Due to the wide range of wires, strands,
insulation diameters, and durometers, actual crimp height measurements may very slightly. An occasional,
destructive, pull force test should be preformed to check hand tool crimp. Pull Force value Must exceed the
Minimum pull force specifications listed.
OPERATION
CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects as
damage can occur to the tool or die.
Open the tool by squeezing the handles together, at the end of
the closing stroke, the ratchet mechanism will release the
handles, and the hand tool will spring open.
Crimping T rminals
1. Select the desired terminal listed in the preceding charts.
2. Position the terminal from the back of the hand tool up and
into the proper locator opening with the crimp barrels
centered over the anvils. See Figure 1. Make sure when
choosing the correct nest and locator opening, it will
correspond with the pocket marked with the wire size profile
on the hand tool.
3. Partially close the jaws of the hand tool by squeezing the
handles until you hear the fist click of the ratchet. This will
move the wire stop into position.
4. From the front of the hand tool insert the pre stripped wire
over the terminal and against the wire stop. See Figure 2.
5. Compress the terminal by squeezing the tool handles until
the ratchet mechanism cycle has been completed. Release handles to open the jaws.
Note: The tamper proof ratchet action will not release the tool until it has been fully closed.
6. Remove the crimped terminal from the terminal locator.
7. Visually inspect the crimped terminal for proper crimp location.
Figur 1 LOCATOR
WIRE STOP
TERMINAL INSIDE
THE GROOVE
OF THE LOCATOR
BACK OF THE
HANDTOOL
Hand Crimp Tool for 0.60mm (.027") CP 0.6 Series Crimp Terminals
Doc No: ATS 638119100 Release Date: 02 12 07 UNCONTROLLED COPY Page 3 of 5
Revision: F Revision Date: 11 22 10
Maint nanc
It is recommended that each operator of the tool be made aware
of, and responsible for, the following maintenance steps:
1. Remove the plastic handles from the metal tool frame by
removing the screws and remove dust, moisture, and other
contaminants with a clean brush, or soft, lint free cloth.
2. Do not use any abrasive materials that could damage the
tool.
3. Make certain all pins; pivot points and bearing surfaces are
protected with a thin coat of high quality machine oil. Do not
oil excessively. The tool was engineered for durability but
like any fine piece of equipment it needs cleaning and
lubrication for a maximum service life of trouble free crimping. Light oil used at the pivot points every 5,000
crimps or 3 months, will significantly enhance the tool life.
4. Wipe excess oil from hand tool, particularly from crimping area.
5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies,
and store the tool in a clean, dry area.
Miscrimps or Jams
Should this tool ever become stuck or jammed in a partially closed
position, Do Not force the handles open or closed. The tool will
open easily by pressing the ratchet release lever up. See Figure 3.
How to Adjust Tool Pr load
It may be necessary over the life of the tool to adjust tool handle
preload force. Listed below are the steps required to adjust the
crimping force of the hand tool to obtain proper crimp conditions:
1. Remove the 2mm locking screw from the numbered adjusting
wheel using a screw driver. See Figure 4.
2. Using the same screw driver turn the adjustment wheel to the
next highest number.
Note: The uneven numbers are in clockwise (CW) direction and the even numbers are counter clockwise
(CCW).
3. Example: If the preload is set at number 5, then to increase the preload, turn the adjustment wheel until the
6th position is located over the 2mm locking screw tapped hole. If it is necessary to move to the 7th position,
then the adjustment wheel should be turned counter clockwise (CCW) until the 7th position is over the 2mm
locking screw tapped hole.
4. Replace the 2mm locking screw, aligning the nearest notch in the setting wheel to locking screw.
5. Check the crimp specifications and conduct a pull test after tool handle preload force is adjusted. Repeat
these steps until the desired result is obtained.
RATCHET
RELEASE LEVER
Figur 3
WIRE
Figur 2
WIRE IS UP AGAINST
THE WIRE STOP
FRONT OF THE
HAND TOOL
TERMINAL
Hand Crimp Tool for 0.60mm (.027") CP 0.6 Series Crimp Terminals
Doc No: ATS 638119100 Release Date: 02 12 07 UNCONTROLLED COPY Page 4 of 5
Revision: F Revision Date: 11 22 10
NUMBERED ADJUSTMENT
WHEEL
Figur 4
TURN CLOCKWISE (CW) OR
COUNTER CLOCKWISE (CCW)
TO ADJUST THE PRE-LOAD
TURN WITH A SMALL
SCREW DRIVER
REMOVE THE LOCKING 2MM SCREW
Warranty
This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital
components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30
days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will
not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping,
fixturing, or use of handle extensions voids this warranty.
CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.
CAUTIONS:
1. Manually powered hand tools are intended for low volume, prototyping, or field repair. This tool is NOT
intended for production use. Repetitive use of this tool should be avoided.
2. Insulated rubber handles are not protection against electrical shock.
3. Wear eye protection at all times.
4. Use only the Molex terminals specified for crimping with this tool.
C rtification
Molex does not certify or re certify hand tools but rather supplies the following guidelines for customers to re
certify hand tools.
% This tool is qualified to pull force only. To re certify, crimp a terminal to a wire, which has been stripped
12.7mm (1/2”) long, so there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than
25mm (1.00”) per minute. See the Molex web site for the Quality Crimp Handbook for more information on pull
testing.
% If the tool does not meet minimum pull force values, handle preload should be increased and the pull test
rerun, (See How to Adjust Preload).
% When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and
replaced.
Hand Crimp Tool for 0.60mm (.027") CP 0.6 Series Crimp Terminals
Doc No: ATS 638119100 Release Date: 02 12 07 UNCONTROLLED COPY Page 5 of 5
Revision: F Revision Date: 11 22 10
1
Figur 5
M3 X 6LG
BHCS
2
3
4
PARTS LIST
It m Numb r Ord r Numb r D scription Quantity
REF 63811-9100 Hand Crimp Tool Figur 5
1 63811 9175 Locator 1
2 11 11 0320 Spring (Ratchet) 1
3 63600 0479 Spring (Main) 1
4 69008 0972 Adjuster Wheel 1
http://www.molex.com
Otros manuales para 207129 Series
100
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Herramientas de crimpado de molex
molex
molex 43178 Series Manual de usuario
molex
molex 63827-8200 Manual de usuario
molex
molex 63825-5770 Manual de usuario
molex
molex 50837 Manual de usuario
molex
molex 63823-8000 Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex Perma-Seal 64005-4500 Manual de usuario
molex
molex 63801-8500 Manual de usuario
molex
molex 63827-1300 Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 63825-7570 Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex AT AFIFG Manual de usuario
molex
molex 63825-1570 Manual de usuario
molex
molex AT-200 Manual
molex
molex 63811-8300 Manual de usuario
molex
molex 63819-2800 Manual de usuario
molex
molex 63819-4100 Manual de usuario
molex
molex 207129 Series Manual de usuario
Manuales populares de Herramientas de crimpado de otras marcas
Textron
Textron ESG105L Manual de usuario
Tyco Electronics
Tyco Electronics 90035-3 Manual de usuario
Emerson
Emerson Klauke ES 20RMCCFB Manual de usuario
Continental Refrigerator
Continental Refrigerator PC150HD Manual de usuario
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario
Tyco Electronics
Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario