Molex CR60639B Manual de usuario

CR60639B Hand Crimp Tool for “Min-Fit Jr.” Terminals

Doc No. 11-01-0198 Release Date: 04-08-93 UNCONTROLLED COPY Page 1 of 5

Revision: E Revision Date: 09-01-05

INSULATION

CRIMP

BRUSH

STRIP

LENGTH

BELL MOUTH

CRIMP HEIGHT

BEND

DOWN

BEND UP

ROLLING

CONDUCTOR

CRIMP

TWISTING

HAND CRIMP TOOL

Operating Instruction and

Specification Sheet

Order No. 11-01-0198

(CR60639B)

FEATURES



Small handle spread which make this style tool ideally suited for end users



Ratchet with safety release that ensures consistent performance



A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position

SCOPE

Wire Size Insulation Diameter Strip Length

Terminal Series No. AWG mm² mm In. mm In.

5556-T2 22 - 28 0.35-0.08 0.90-1.80 .035-.071 2.79-3.30 .110-.130

5558-T2 22 - 28 0.35-0.08 0.90-1.80 .035-.071 2.79-3.30 .110-.130

DEFINITION OF TERMS

The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope.

CR60639B Hand Crimp Tool for “Min-Fit Jr.”Terminals

Doc No. 11-01-0198 Release Date: 04-08-93 UNCONTROLLED COPY Page 2 of 5

Revision: E Revision Date: 09-01-05

Figure 2

CONDITIONS:

After crimping, the conductor profiles should measure the following (see notes on page 4).

Punch Width (Ref)

Wire Size Cond. Crimp Height

(Ref) Cond. Ins.

Pull Force Min. Profile

Terminal Series No.

AWG mm2mm In. mm In. mm In. N Lb. A B

5556-T2 22 0.35 0.76-0.86 .030-.034 1.42 .056 1.68 .066 40.0 9.00 X

5556-T2 24 0.20 0.69-0.79 .027-.031 1.42 .056 1.68 .066 31.1 7.00 X

5556-T2 26 0.12 0.64-0.74 .025-.029 1.42 .056 1.68 .066 22.2 5.00 X

5556-T2 28 0.08 0.61-0.71 .024-.028 1.42 .056 1.68 .066 13.3 3.00 X

5558-T2 22 0.35 0.76-0.86 .030-.034 1.42 .056 1.68 .066 40.0 9.00 X

5558-T2 24 0.20 0.69-0.79 .027-.031 1.42 .056 1.68 .066 31.1 7.00 X

5558-T2 26 0.12 0.64-0.74 .025-.029 1.42 .056 1.68 .066 22.2 5.00 X

5558-T2 28 0.08 0.61-0.71 .024-.028 1.42 .056 1.68 .066 13.3 3.00 X

OPERATION

Open the tool by squeezing the handles together, at the end of the closing stroke, the ratchet mechanism will release the handles,

and the hand tool will spring open.

Crimping Terminals

1. Lift the locator blade and place the terminal into the correct die

profile (A or B), release the locator blade. Not all tools are

equipped with a locator or locator blade.

2. Partially close the tool until the terminal is held in place, (See

Figure 1). If the insulation diameter is too large to do this, then

place the insulation down into the terminal before closing the

tool.

TERMINAL

PRE-STRIPPED WIRE

Figure 1

CR60639B Hand Crimp Tool for “Min-Fit Jr.”Terminals

Doc No. 11-01-0198 Release Date: 04-08-93 UNCONTROLLED COPY Page 3 of 5

Revision: E Revision Date: 09-01-05

Figure 3

3. Place a wire into the terminal and up against the locator blade, (See Figure 2).

On tools without locators line the wire up with the conductor and insulation

grips visually.

4. Close the tool until the ratchet releases, (See Figure 3).

5. Lift the locator blade or wire stop up.

6. Carefully remove the crimped terminal.

Maintenance

It is recommended that each operator of the tool be made aware of, and responsible

for, the following maintenance steps:

1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth.

2. Do not use any abrasive materials that could damage the tool.

3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine oil. Do not oil

excessively.

4. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies, and store the tool in

a clean, dry area.

Miscrimps or Jams

Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or closed. The tool will open

easily by lifting the ratchet release lever (See Figure 4).

How To Adjust Tool Crimp Force (See Figure 4)

It may be necessary over the life of the tool to adjust tool-crimping force. Listed below are the steps required to adjust the crimping

force of the hand tool to obtain proper crimp conditions:

1. Remove the screw and washer. Located over the adjustment ring.

2. Lift the adjusting ring slightly, off of the locating pin.

3. Turn the adjusting ring in the desired direction (L= less force, T= more force) to increase or decrease crimp pressure.

4. Press the adjusting wheel flat against the tool and engage the locking pin.

5. Replace the washer and screw.

6. Check the crimp specifications after tool crimp force is adjusted.

Warranty

This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital components are long

life tested. All tools are warranted to be free of manufacturing defects for a period of 30 days. Should such a defect occur, we would

exchange the tool free of charge. This will not be applicable to altered, misused, or damaged tools. This tool is designed for hand use

only. Any clamping, fixturing, or use of handle extensions voids this warranty.

CR60639B Hand Crimp Tool for “Min-Fit Jr.”Terminals

Doc No. 11-01-0198 Release Date: 04-08-93 UNCONTROLLED COPY Page 4 of 5

Revision: E Revision Date: 09-01-05

Hand held crimping tools are intended for low volume, prototyping, or repair requirements only.

CAUTION: Repetitive use of this tool should be avoided.

Notes:

1. This tool should only be used for the terminals and wire gauges specified on this sheet.

2. This tool is not adjustable for crimp height, however crimp force is adjustable (See instructions above). Variations in tools,

terminals, wire stranding and insulation types may affect crimp height.

3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all insulation sizes.

4. Molex does not repair hand tools (see warranty above) The replacement parts listed are the only parts available for repair. If the

handles or crimp tooling is damaged or worn, a new tool must be purchased.

5. Pull force should be used as the final criteria for an acceptable crimp. Pull force is measured with no influence from the insulation

crimp. The insulation should be stripped long (1/2 in.) so the insulation grips on the terminal do not grip the wire insulation or the

conductor. Refer to Molex Quality Crimping Handbook 63800-0029 for additional information on crimping and crimp testing.

6. Molex does not certify crimp hand tools.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and tooling.

CR60639B Hand Crimp Tool for “Min-Fit Jr.”Terminals

Doc No. 11-01-0198 Release Date: 04-08-93 UNCONTROLLED COPY Page 5 of 5

Revision: E Revision Date: 09-01-05

M4 NUT

RATCHET

RELEASE LEVER

ADJUSTMENT

RING

LOCATOR

BLADE

Figure 4

M4 X 18LG BHCS

PARTS LIST

Item Number Order Number Description Quantity

1 11-11-0377 Locator Assembly** 1

2 11-11-0324 Spring (Main) 1

3 11-11-0320 Spring (Ratchet) 1

** Not all tools are equipped with a locator or locator blade.

Molex Application Tooling Group

1150 E. Diehl Road

Naperville, IL, 60563

Tel: 630-969-4550

Fax: 630-505-0049

Visit our Web site at http://www.molex.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas de crimpado de molex

molex

molex 63819-4400 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex MV-396 Guía del usuario

molex

molex 63825-4800 Manual de usuario

molex

molex 63816-0200 Manual de usuario

molex

molex 50837 Manual de usuario

molex

molex 63823-7570 Manual de usuario

molex

molex 63825-6070 Manual de usuario

molex

molex TPX50-50 Guía del usuario

molex

molex 207125 Series Manual de usuario

molex

molex 105300 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex MOLEX Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63819-2800 Manual de usuario

molex

molex 63801-8500 Manual de usuario

molex

molex 63823-5100 Guía del usuario

molex

molex 207129 Series Manual de usuario

molex

molex CR1031E Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex CR5907 Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario

molex CR60639B Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas