Mitsubishi Wi-Fi Control Manual de usuario

INSTALLATION GUIDE

Setting Information

MAC-559IF-E Address(MAC)

MAC-559IF-E Serial Number(ID)

MAC-559IF-E Code(PIN)

Indoor Unit Model Name

Indoor Unit Serial Number

Outdoor Unit Model Name

Outdoor Unit Serial Number

System Commissioning Date

MAC-559IF-E Installation Date

Installer Contact Details

Name

Telephone Number

Wi-Fi Control Minimum Requirements for Operation:

• Compatible WPS router, capable of WPA2-AES

encryption. The wireless network coverage must include

the heat pump installation location;

• A PC or Tablet/Smartphone that is iOS/Android

compatible;

• A compatible Mitsubishi Electric Heat Pump with a

MAC-559IF-E Adaptor.

Once registered you will be able to control your heat pump with your

smartphone, tablet or online account using an internet connection (for

a list of compatible devices please visit the Mitsubishi Electric website).

User Manual

A copy of the user manual, terms & conditions and

from the Mitsubishi Electric website.

Mitsubishi Electric Wi-Fi Heat Pump Control

Thank you for choosing a Mitsubishi Electric Heat Pump with Wi-Fi

Control. Once your adaptor is installed, either download the app

(search term: Mitsubishi Electric) or visit our website to register

your heat pump(s).

Mitsubishi Electric New Zealand

www.mitsubishi-electric.co.nz/wifi

Phone: 0800 639 434

Mitsubishi Electric Australia

www.mitsubishielectric.com.au/wifi

Phone: 1300 728 119

Important Note: Before carrying out installation of the MAC-559IF-E adaptor

please read the safety instructions listed on page 8 of this installation guide.

The following steps explain how to connect the MAC-559IF-E

Adaptor to a Mitsubishi Electric Heat Pump.

*Please note: the appearance of the outdoor unit may differ dependant on model type

Wi-Fi Control: Installation Instructions

Information for installers:

EQUIPMENT REQUIRED FOR INSTALL:

MAC-559IF-E

Adaptor

WPS Enabled

Router

Wi-Fi

Installation

Guide

Tools to remove

cover of indoor

unit

#2 Phillips

Important Note: Before going to the users home, ensure they have a WPS

capable router and WPA2-AES encryption can be set. For ease of access,

please do not install the Wi-Fi Adaptor inside high wall indoor unit cabinets.

Record the adaptor’s MAC, ID

number and serial numbers on page

2 of the Wi-Fi Installation Guide.

Isolate the outdoor unit*and verify

power has been disconnected from

the complete system.

INSTALLATION GUIDE

Run the cables down the back of

the unit with the other cables. Tuck

cabling away and secure. Adapter

can be placed on top of window.

Reassemble the indoor unit and

restore power to the system.

Check that the MAC-559IF-E

Adaptor is flashing. The install has

now been completed.

The adaptor is now able to be

connected to the user’s router. Steps for

this are shown on the following pages.

7 8

Remove the cover of the indoor

unit, the cable terminal, and the

cover to the control board.

Locate the CN105 port* on the

main control board and connect

the MAC-559IF-E Adaptor.

3 4

*Note: CN105 connection on some MSZ-GE models is located below the remote control

sensor of indoor unit. The above illustrates high wall unit installation. Installation and

appearance will vary depending on indoor model type.

Wi-Fi Control: Installation Instructions

Information for users:

The following steps explain how to connect the MAC-559IF-E

Adaptor to a router.

KEY (LED LIGHTS):

ON OFF FLASHING

Check Wi-Fi and WPS are enabled

on your router. The connection

procedure varies depending on

your router – refer to your router

manual for more information.

Activate WPS mode on your router.

This will be enabled for a set

period allowing approximately two

minutes to complete Step 3.

To do so please refer to your

router’s manual.

Activate WPS on your adaptor by

using a small object to press and hold

the WPS button for two seconds.

1 2

3Please Note: The WPS and

router reset buttons may

be similar on some routers.

Please exercise caution as

resetting your router will

erase network configuration.

When LED 1 remains solid for 5

seconds the adaptor is connecting

to your router.

Next, the bottom light (LED 3) will

start flashing as it connects to the

internet. This may continue for up

to 4 minutes.

When LED 1 and LED 3 flash

alternately the unit is successfully

connected to the internet.

If LED 2 (orange) lights up at any

stage there may be a problem.

Check the troubleshooting section

on page 11.*

You can now download the

Mitsubishi Electric Wi-Fi Control

App and control your heat pump

via Wi-Fi.

Turn the adaptor over and check

LED 1 (top light) is flashing.

*You can restart the connection process at anytime by starting again from Step 1.

Safety Instructions

• Read all safety instructions before using the Wi-Fi Adaptor.

• This installation manual contains important safety information. Be sure to

comply with the instructions.

• After installing the Wi-Fi Adaptor, provide this installation manual to the

user. Instruct users to store it with their heat pump instruction manual in

a safe location.

Warning

(Improper handling may have serious consequences, including serious injury or death.)

• Installation of the adaptor must be carried

out by an authorised installer only.

• Improper installation may result in fire,

electric shock, or damage/water leaks.

Consult the dealer from whom you

purchased the unit, or a professional

installer.

• The adaptor should be securely

installed in accordance with this

installation manual.

• The unit should be mounted in a location

that can support its weight.

• If the unit is installed in a location that

cannot support its weight, the Wi-Fi

Adaptor could fall and cause damage.

• Connect and fasten the electric wires

securely so external force on the wires will

not apply on the terminals.

• Improper connection and mounting may

result in breakdown, heat generation,

smoke generation, or fire.

• Mitsubishi Electric components or other

designated components must be used for

installation.

• Improper components may result in fire,

electric shock, or damage/water leaks.

• Electrical work must be performed

by a licensed professional using the

instructions detailed in the installation

manual.

• Inadequate circuit capacity or improper

installation may result in electric shock

or fire.

• This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities,

or lack of experience and knowledge,

unless they have been given supervision

or instruction concerning use of the

appliance by a person responsible for

their safety.

• Children should be supervised to ensure

that they do not play with the appliances.

• This device complies with all Australia

and New Zealand requirements for EMC

and electrical safety.

• Do not connect the Wi-Fi Adaptor to earth

inside the heat pump.

Caution

(Improper handling may have consequences, including injury or damage to house.)

• To prevent damage from static electricity,

touch a nearby metal body to discharge

static electricity from yourself before

touching the Wi-Fi Adaptor.

• Static electricity from the human body may

damage the Wi-Fi Adaptor unit.

• Do not install the Wi-Fi Adaptor in a place

with high steam levels, such as bathrooms.

• Avoid places where water is splashed

or where condensation forms on walls.

Installing in such places can cause electric

shock or breakdown.

• Do not install the Wi-Fi Adaptor in places

with direct sunlight or where the ambient

temperature is 40ºC or more or is 0ºC

or less. Direct sunlight and high or low

temperature environments may cause the

Wi-Fi Adaptor to deform or breakdown.

• Do not use in special environments.

• Do not use in places with high oil use

(including machine oil), high steam levels,

or sulfuric gas - this may lead to severe

decrease in functionality and damage to

parts.

• Turn off power supply of connected

equipment when performing construction or

wiring work.

• Failure to turn off the power supply to

the connected equipment may lead to

malfunction or breakdown of the Wi-Fi

Adaptor or connected equipment.

• Dismantling the indoor unit

Please refer to the indoor units “service

manual” for detailed instructions for

accessing the control adaptor connector

CN105 on the indoor unit control PCB.

Note

• Please ensure that the access point

supports both WPS connection and the

WPA2-AES encryption setting before

commencement of the installation of the

MAC-559IF-E.

• To complete connection of the

MAC-559IF-E to the Wi-Fi service physical

access to the access point may be required.

• Details of the heat pump and

MAC-559IF-E can be recorded on page 2

‘Setting Information’.

• The end user should read and accept the

terms and conditions of the Wi-Fi service

before commencement of the installation of

MAC-559IF-E.

• The MAC-559IF-E should not be installed

and connected to any Mitsubishi Electric

system which is to provide cooling or

heating to critical applications.

Mitsubishi Electric’s Wi-Fi Adaptor is designed for communication to Mitsubishi Electric’s

Wi-Fi service.

Third party Wi-Fi Adaptors cannot connect to Mitsubishi Electric’s Wi-Fi service.

Mitsubishi Electric is not responsible for any (i) under performance of a system or any product;

(ii) system or product fault; or (iii) loss or damage to any system or product; which is caused by

or arises from connection to and/or use of any third party Wi-Fi Adaptor or any third party Wi-Fi

service with Mitsubishi Electric equipment.

For the latest information regarding Wi-Fi Control:

New Zealand based enquiries please visit: www.mitsubishi-electric.co.nz/wifi

Australian based enquiries please visit: www.mitsubishielectric.com.au/wifi

LED pattern

Description LED1 LED2 LED3

Power is ON or software downloaded (0.5-sec interval) (0.5-sec interval) (0.5-sec interval)

ALL settings reset

WPS activated (PBC) (0.5-sec interval)

WPS activated (PIN) (0.2-sec interval)

WPS enabled (5-sec)

WPS failed (5 sec)

Server and access point communication connected, and

heat pump communication failed (once every 5 sec) (0.5-sec interval)

Server and access point communication connected, and

heat pump communication connected (once every 5 sec) (once every 5 sec)

Server and access point communication connected, and

heat pump communication starting up (once every 5 sec)

Server communication failed, and heat pump

communication connected (0.5-sec interval) (once every 5 sec)

Server communication or access point communication

failed, and heat pump communication starting up (0.5-sec interval)

Server communication or access point communication

failed, and heat pump communication failed (0.5-sec interval)

Access point communication failed, and

heat pump communication connected (once every 5 sec)

Access point communication failed, and

heat pump communication starting up

:ON :OFF :Flashing

Parts

Adaptor unit

[with connecting

cable (5-core)]

Optional screw

for mounting

3.5×16

Optional screw

for mounting

4×16

Optional

mounting cord

clamp

Fastener (for

bundling the

wires)

Product Introduction

No Item Description

1 WPS switch Activates WPS

2 RESET switch Resets the system and ALL settings

3 LED1 (Green) Shows the wireless communication state

4 LED2 (Orange) Shows the MAC-559IF-E state

5 LED3 (Green) Shows the local communication state

Tabla de contenidos

Otros manuales de Unidad de control de Mitsubishi

Mitsubishi

Mitsubishi MELSEC-A A1S68AD Manual de usuario

Mitsubishi

Mitsubishi C70 Manual de usuario

Mitsubishi

Mitsubishi AJ65SBT2B-64AD Manual de usuario

Mitsubishi

Mitsubishi MELSEC-Q QD77MS Manual de usuario

Mitsubishi

Mitsubishi Q64AD Manual de usuario

Mitsubishi

Mitsubishi QJ71NT11B Manual de usuario

Mitsubishi

Mitsubishi MELSEC Q Series Manual de usuario

Mitsubishi

Mitsubishi MELSEC System Q Manual de usuario

Mitsubishi

Mitsubishi MELSEC-F FX-1GM Instrucciones de montaje

Mitsubishi

Mitsubishi M800S series Guía de configuración

Mitsubishi

Mitsubishi MELSEC-Q Q Series Manual de usuario

Mitsubishi

Mitsubishi MELSECNET/10 A1SJ72QLP25 Manual de usuario

Mitsubishi

Mitsubishi FX2N Manual de usuario

Mitsubishi

Mitsubishi A0J2CPU Manual de usuario

Mitsubishi

Mitsubishi A1SJ71AP21 Manual de usuario

Mitsubishi

Mitsubishi MELSEC A1S64AD Manual de usuario

Mitsubishi

Mitsubishi A8GT-50KBF Manual de usuario

Mitsubishi

Mitsubishi A1SD75M3 Manual de usuario

Mitsubishi

Mitsubishi Q Series Manual de usuario

Mitsubishi

Mitsubishi AJ71PB92D Manual de usuario

Mitsubishi

Mitsubishi Q68TD-G-H01 Manual de usuario

Mitsubishi

Mitsubishi MELSEC-A A1SJ71AS92 Manual de usuario

Mitsubishi

Mitsubishi MAC-588IF-E Manual de usuario

Mitsubishi

Mitsubishi Melsec-A AJ65SBT Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario