Mitsubishi QJ71WS96 Series Manual de usuario

Web Server Module

User's Manual

(Hardware)

QJ71WS96

Thank you for purchasing the Mitsubishi programmable controller

MELSEC-Q Series.

Prior to use, please read both this manual and detailed manual

thoroughly to fully understand the product.

MODEL QJ71WS96-U-HW-JE

MODEL

CODE 13JT97

IB(NA)-0800231-F(0903)MEE

2002 MITSUBISHI ELECTRIC CORPORATION

-1

DANGER

CAUTION

zSAFETY PRECAUTIONS z

(Always read these instructions before using this equipment.)

Before using this product, please read this manual and the relevant manuals

introduced in this manual carefully and pay full attention to safety to handle the

product correctly.

Note that these instructions apply only to this product. Refer to the user's manual

of the CPU module for the programmable controller system safety instructions.

In this manual, the safety instructions are ranked as "DANGER" and "CAUTION".

Indicates that incorrect handling may cause hazardous

conditions, resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous

conditions, resulting in medium or slight personal injury or

physical damage.

Note that the CAUTION level may lead to a serious consequence according

to the circumstances.

Always follow the instructions of both levels because they are important to

personal safety.

Please save this manual to make it accessible when required and always forward

it to the end user.

-2

[Design Precautions]

CAUTION

zDo not bunch the control wires or communication cables with the main circuit

or power wires, or install them close to each other.

They should be installed 100 mm (3.94 inch) or more from each other.

Not doing so could result in noise that would cause erroneous operation.

zDo not power off a station where this module is mounted and do not reset the

programmable controller CPU while storing the settings into the standard

ROM of the module using a Web browser.

This may make the data unstable within the standard ROM and require

resetting and re-storing, or it may cause a failure or malfunctions of the

module.

[Installation Precautions]

CAUTION

zUse the programmable controller in the environment specified in the user's

manual of the CPU module.

Using this programmable controller in an environment outside the range of

the general specifications could result in electric shock, fire, erroneous

operation, and damage to or deterioration of the product.

zWhile pressing the installation lever located at the bottom of module, insert

the module fixing tab into the fixing hole in the base unit until it stops. Then,

securely mount the module with the fixing hole as a supporting point.

Incorrect loading of the module can cause a malfunction, failure or drop.

When using the programmable controller in the environment of much

vibration, tighten the module with a screw.

zCompletely turn off the externally supplied power used in the system before

mounting or removing the module.

Not doing so could result in damage to the product.

zTighten the screw in the specified torque range.

Undertightening can cause a drop, short circuit or malfunction.

Overtightening can cause a drop, short circuit or malfunction due to damage

to the screw or module.

zDo not directly touch the module's conductive parts or electronic

components.

Touching the conductive parts could cause an operation failure or give

damage to the module.

zFor connector wiring, correctly press, pressure-weld or solder the connecting

part by using the tool specified by the manufacturer.

Poor connection may cause short circuits, fires or malfunctions.

zBe sure to set the CompactFlash card by pressing it into the CompactFlash

card slot. Confirm it is completely set.

Poor contact may lead to malfunctions.

-3

[Wiring Precautions]

CAUTION

zBe sure to fix communication cables and power cables to the module by

ducts or clamps.

Failure to do so may cause damage of the module or the cables due to

accidental pull or unintentional shifting of the cable, or malfunctions due to

poor contact of the cables.

zConnect the connectors to the module securely.

zTighten the terminal screws with the specified torque.

If the terminal screws are loose, it could result in short circuits, fire, or

erroneous operation.

Tightening the terminal screws too far may cause damages to the screws

and/or the module, resulting in fallout, short circuits, or malfunction.

zDo not hold the communication cable by hand when pulling it out from the

module.

Be sure to hold the connector by hand, when removing the cable with a

connector from the module.

Failure to do so may cause malfunctions or damage to the module or cable.

zBe sure there are no foreign substances such as sawdust or wiring debris

inside the module. Such debris could cause fires, damage, or erroneous

operation.

zThe module has an ingress prevention label on its top to prevent foreign

matter, such as wire offcuts, from entering the module during wiring.

Do not peel this label during wiring.

Before starting system operation, be sure to peel this label because of heat

dissipation.

[Disposal Precautions]

CAUTION

zWhen disposing of this product, treat it as industrial waste.

When disposing of batteries, separate them from other wastes according to

the local regulations. (For details of the battery directive in EU member

states, refer to the Web Server Module User's Manual.)

[Transportation Precautions]

CAUTION

zWhen transporting lithium batteries, make sure to treat them based on the

transport regulations. (Refer to Chapter 8 for details of the controlled

models.)

-4

Revisions

* The manual number is given on the bottom left of the back cover.

Print Date *Manual Number Revision

July, 2002 IB(NA)-0800231-A First printing

Nov., 2002 IB(NA)-0800231-B Correction

Section 3.1(2), Chapter 4, Section 5.2(2)

Nov., 2003 IB(NA)-0800231-C Correction

Chapter 2, Chapter 6

Addition

Safety Precautions, Section 3.1 (2),

Chapter 8

Dec., 2007 IB(NA)-0800231-D Change of a term

"PLC" was changed to "programmable

controller".

Correction

SAFETY PRECAUTIONS, Compliance

with the EMC and Low Voltage Directives,

Chapter 1, Chapter 2, Section 3.1,

Section 5.1, Section 5.2, Section 8.1

Sep., 2008

IB(NA)-0800231-E Correction

SAFETY PRECAUTIONS, Compliance

with the EMC and Low Voltage Directives,

Section 3.1

Mar., 2009

IB(NA)-0800231-F Correction

SAFETY PRECAUTIONS, Chapter 4,

Chapter 7

This manual confers no industrial property rights or any rights of any other kind, nor does it

confer any patent licenses. Mitsubishi Electric Corporation cannot be held responsible for

any problems involving industrial property rights which may occur as a result of using the

contents noted in this manual.

2002 MITSUBISHI ELECTRIC CORPORATION

-5

CONTENTS

1. Overview........................................................................................................ 1

2. Performance Specifications ........................................................................... 2

3. Mounting and Installation ............................................................................... 3

3.1 Handling Precautions ............................................................................... 3

3.2 Installation Environment ........................................................................... 3

4. Part Names.................................................................................................... 4

5.External Wiring ............................................................................................... 6

5.1 Connecting to the 10BASE-T/100BASE-TX ............................................. 6

5.2 Connecting to the RS-232 ........................................................................ 7

6. Setting from GX Developer ............................................................................ 8

7. External Dimensions.................................................................................... 11

8. Transportation Precautions.......................................................................... 12

8.1 Target Models of Regulations................................................................. 12

8.2 Transport Guidelines .............................................................................. 12

-6

About Manual

The following manual is also related to this product.

In necessary, order it by quoting the details in the table below.

Related Manual

Manual name Manual No.

(Model code)

Web Server Module User's manual SH-080320E

(13JR58)

Compliance with the EMC and Low Voltage Directives

(1) For programmable controller system

To configure a system meeting the requirements of the EMC and Low

Voltage Directives when incorporating the Mitsubishi programmable

controller (EMC and Low Voltage Directives compliant) into other

machinery or equipment, refer to Chapter 9 "EMC AND LOW VOLTAGE

DIRECTIVES" of the QCPU User's Manual (Hardware Design,

Maintenance and Inspection).

The CE mark, indicating compliance with the EMC and Low Voltage

Directives, is printed on the rating plate of the programmable controller.

(2) For the product

For the compliance of this product with the EMC and Low Voltage

Directives, refer to Section 9.1.3 "Cables" in Chapter 9 "EMC AND LOW

VOLTAGE DIRECTIVES" of the QCPU User's Manual (Hardware Design,

Maintenance and Inspection).

1. Overview

This manual explains how to install the QJ71WS96 Web server module

(hereinafter referred to as Web server module) and how to wire them with other

devices.

(Packing list)

Model name Product name Quantity

QJ71WS96 Web server module 1

QJ71WS96 Battery (Q6BAT) 1

2. Performance Specifications

The following describes the performance specifications of the Web server

module.

For the general specifications of the Web server module, refer to the user's

manual of the CPU module used.

Item Specifications

10BASE-T/100BASE-TX -

Interface (*1) 10BASE-T 100BASE-TX

Data transmission speed 10Mbps 100Mbps

Transmission method Base band

Number of cascaded

stages

Cascade connection

Maximum 4 stages

Cascade connection

Maximum 2 stages

Maximum segment

length(*2) 100m

Supported function Auto negotiation function

(automatically recognizes 10BASE-T/100BASE-TX)

RS-232 -

Interface Compliance with RS-232 (D-sub 9 pin)

Communication method Full-duplex communication

Synchronization method Start-stop synchronization method

Transmission speed 9600, 19200, 38400, 57600, 115200 bps

Transmission distance Maximum 15m

Start bit 1

Data bit 8

Data format

Stop bit 1

Parity check None

Transmission control Flow control (RS/CS control) is available

Recommended cable

7/0.127 P HRV-SV outside diameter: 8.5mm or longer

(Oki Electric Cable Company, Limited

Specify the number of pairs in .)

External wiring applicable

connector 9 pin D-sub (Male) fixing type

CompactFlash card -

Supply power voltage 3.3V 5%

Supply power capacity Maximum 150mA

Size TYPE card

Number of mountable cards 1

Number of occupied I/O points 32 points/1 slot (I/O assignment: intelligent 32 points)

Maximum number of writes for

Standard ROM (Flash ROM) Maximum 100,000 times to one area

Clock The clock data is obtained from a programmable controller

CPU (in multiple CPU system, CPU No.1) (every 60s)

5V DC internal current

consumption 0.65A

External dimensions 98 (3.86 in.) (H) 27.4 (1.08 in.) (W) 90 (3.54 in.) (D) [mm]

Weight 0.17 kg (0.37Ib.)

*1: Web server module recognizes 10BASE-T/100BASE-TX according to the

external device.

For connection with the hub that does not have the auto negotiation function,

set the hub side to the half-duplex communication mode.

*2: Distance between the hub and node.

3. Mounting and Installation

3.1 Handling Precautions

(1) Do not drop or apply severe shock to the module case since it is made of

resin.

(2) Before touching the module, always touch grounded metal, etc. to

discharge static electricity from human body, etc.

Not doing so can cause the module to fail or malfunction.

(3) Tighten the screws such as module fixing screws within the following

ranges.

Screw position Tightening torque range Remarks

Module fixing screw

(usually not required)

(M3 screw) (*1)

0.36 to 0.48 N•m -

RS-232 cable connector

screw (M2.6) 0.20 to 0.39 N•m

Screw hole depth:

L=3.2mm or less

(Internal dimension from

end face)

*1: The module can be easily fixed onto the base unit using the hook at the

top of the module.

However, it is recommended to secure the module with the module

fixing screw if the module is subject to significant vibration.

3.2 Installation Environment

For details, refer to the user's manual for the CPU module used.

Otros manuales para QJ71WS96 Series

Tabla de contenidos

Otros manuales de Unidad de control de Mitsubishi

Mitsubishi

Mitsubishi Melsec-Q QD63P6-U-HW Manual de usuario

Mitsubishi

Mitsubishi FX3U-ENET-ADP Manual de usuario

Mitsubishi

Mitsubishi FX1N-5DM Manual de usuario

Mitsubishi

Mitsubishi MELSEC-F FX-1GM Instrucciones de montaje

Mitsubishi

Mitsubishi QD75M1 Manual de usuario

Mitsubishi

Mitsubishi MELDAS MDS-C1 Manual de usuario

Mitsubishi

Mitsubishi C70 Manual de usuario

Mitsubishi

Mitsubishi MELSEC-A Manual de usuario

Mitsubishi

Mitsubishi Q Series Manual de usuario

Mitsubishi

Mitsubishi MELSEC-A A1SJ71PB93D Manual de usuario

Mitsubishi

Mitsubishi QJ72LP25-25 Instrucciones de uso

Mitsubishi

Mitsubishi NZ2GF2B-60DA4 Manual de usuario

Mitsubishi

Mitsubishi L Series Manual de usuario

Mitsubishi

Mitsubishi AJ65BT-64DAV Manual de usuario

Mitsubishi

Mitsubishi A1SJ71AP21 Manual de usuario

Mitsubishi

Mitsubishi MELSEC-A series Manual de usuario

Mitsubishi

Mitsubishi GOT 1000 Manual de usuario

Mitsubishi

Mitsubishi AJ71PB92D Manual de usuario

Mitsubishi

Mitsubishi MELSEC QD75P Manual de usuario

Mitsubishi

Mitsubishi Wi-Fi Control Manual de usuario

Mitsubishi

Mitsubishi MELSEC L Series Manual de usuario

Mitsubishi

Mitsubishi MELSEC-A AJ71DN91 Manual de usuario

Mitsubishi

Mitsubishi MELSEC-L Series Manual de usuario

Mitsubishi

Mitsubishi MELSEC L Series Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario