Mitsubishi FR-A5ND Manual de usuario

FR-A5ND

DeviceNetTM Communications

Option Unit

used with

A500(L) Series

Variable Frequency Drive

Instruction Manual

MITSUBISHI ELECTRIC

AUTOMATION

MITSUBISHI ELECTRIC AUTOMATION

DeviceNet is a registered trademark of Open DeviceNet Vendor Association (ODVA).

DeviceNetManager is a trademark of Allen-Bradley Company Inc.

Windows, DOS and other product names may be trademarks or registered trademarks of

their respective companies.

FR-A5ND

DeviceNetCommunications Option Unit

iii

NOTES, CAUTIONS AND WARNINGS

NOTE: Notes are used to provide additional detail about a procedure. The

Note will always precede the text that the Note refers to.

CAUTION: Cautions provide additional detail where failure to observe the

Caution may result in damage to the equipment or slight injury

to the user.

WARNING: Warning provide additional information, where failure to observe

the Warning may result in death or severe injury

SAFETY INSTRUCTION

1. Electric Shock Prevention

WARNING:  Do not open or remove the front cover while the Variable

Frequency Drive is running. You may get an electrical shock.

 When necessary to perform inspections or when wiring the

unit, switch power off and wait at least 10 minutes and until

the bus charge light is off. Check for residual voltage.

 Do not attempt to inspect or wire this unit unless fully com-

petent to perform the work.

 Be sure hands are dry before operating any switches.

 Be sure cables do not have scratches, excessive stress,

heavy loads or pinching to prevent electrical shock

2. Injury Prevention

CAUTION:  Be sure all connections are in accordance with instructions

in this manual

 Check that cables are properly connected before turning

equipment on.

 After turning equipment off, wait at least 10 minutes and

until the bus charge light is off before removing cover. With

cover removed, charged components may be exposed.

MITSUBISHI ELECTRIC AUTOMATION

3. Additional Cautions and Warnings

CAUTION:  Do not install the option unit if it is damaged or has parts

missing

 Check that option unit is securely fastened to the variable

frequency drive.

 Do not stand or rest heavy objects on top of unit.

 Do not allow metal fragments, conductive bodies, oil or other

flammable substance to enter the variable frequency drive.

 Before starting operation, confirm and adjust the parameters.

Failure to do so may cause the machines to make unex-

pected motions.

 When parameter clear or all parameter clear is performed,

each parameter returns to the factory setting. Reset the

required parameters before starting operation

 For prevention of damage caused by static buildup, touch a

nearby metal object to remove static from your body.

 Dispose of this product as general industrial waste.

WARNING:  Do not modify this equipment

FR-A5ND

DeviceNetCommunications Option Unit

TABLE OF CONTENTS

Page

1. INTRODUCTION .............................................................................. 1

General ............................................................................................. 1

Description ....................................................................................... 1

2. INSTALLATION ................................................................................ 3

2.1. Pre-Installation Checks .............................................................. 3

2.2. Installation Procedures .............................................................. 4

2.3 Pre Network Connection Procedure ............................................ 8

2.4 Connection to Network ................................................................ 9

2.5 Changing Node Addresses ....................................................... 10

2.6 LED Status Indicator................................................................. 11

3. GETTING STARTED .......................................................................... 12

3.1. Introduction .............................................................................. 12

3.2. Basic Configuration .................................................................. 13

3.3. Loss of Communications ......................................................... 14

4. OPERATION ...................................................................................... 14

4.1. Operation Modes ..................................................................... 14

4.2. Operation Mode Selection ...................................................... 15

4.3. Functions Available in Operation Modes .................................. 16

4.4. Input from DeviceNet to VFD .................................................... 16

4.5. Output from VFD to DeviceNet ................................................. 17

4.6. Operation on Alarm Occurrence ............................................... 19

4.7. VFD Reset............................................................................... 19

4.8. Setting Frequency (f) Value...................................................... 19

4.9. Parameter Clear (Pr Clr) Commands ........................................ 19

4.10. Control Input Commands .......................................................... 20

5. FR-A5ND SPECIFIC PARAMETERS .................................................. 20

5.1. Prs.345 & 346 ......................................................................... 20

5.2. Other Option-Specific Parameters ........................................... 24

6. OBJECT MAP .................................................................................... 25

6.1. Class 0x01 - Identity Object..................................................... 25

6.2. Class 0x03 - DeviceNet Object ................................................ 26

6.3. Class 0x04 - Assembly Object ................................................ 27

6.4. Class 0x05 - DeviceNet Connection Object .............................. 31

MITSUBISHI ELECTRIC AUTOMATION

6.5. Class 0x28 - Motor Data Object ............................................... 37

6.6. Class 0x29 - Control Supervisor Object .................................... 38

6.7. Class 0x2A - AC Drive Object .................................................. 39

6.8. Class 0x66 - A500(L) Extended Object I .................................. 43

6.9. Class 0x67 - A500(L) Extended Object II ................................. 49

6.10. Response Timing ................................................................... 55

6.11. Recommendation For Software Developers ............................ 55

7. A500(L) PARAMETERS ..................................................................... 56

8. TROUBLESHOOTING ....................................................................... 65

8.1. Inspecting Display On Parameter Unit And MNS

Status LED On A5ND ............................................................. 65

9. REFERENCES ................................................................................... 66

10. SPECIFICATIONS ........................................................................... 67

APPENDIX A ......................................................................................... 68

REVISIONS ........................................................................................... 69

FR-A5ND

DeviceNet

Communications Option Unit

1. INTRODUCTION

GENERAL

The purpose of this manual is to provide general information, installation, and

operation procedures for the FR-A5ND DeviceNet option, used with the

FR-A500(L) Variable Frequency Drive, herein after referred to as the VFD.

Read this manual completely before installing, operating or servicing the

option unit.

This manual is intended for use by qualified personnel. Installation should

only be performed by qualified personnel. You must be able to operate and

program serial devices to use the equipment.

This option allows the VFD to be connected to a network adhering to the

DeviceNet communications protocol.

Illustrations provided in this manual may have covers or safety guards re-

moved to provide a clear view. Before starting operation of the product be sure

to install covers and guards into the original position.

The following is a list of important features for the option unit

 Data Rates of 125K baud, 250K baud, and 500K baud.

 Up to 64 stations supported on a single network

 Ability to add or remove stations without disrupting network operation.

 Network access to all VFD parameters, Start/Stop commands, and moni-

tor data.

 Passed ODVA Conformance Test in January, 1998

 Designed and assembled in the U.S.A..

DESCRIPTION

The FR-A5ND option unit consists of two circuit boards as shown in Figure

1-1. The option unit is mounted in option port #3 on the VFD unit. Two station

switches, mounted on the top printed circuit board, allow the assigning of

station numbers from 0 to 63. An LED status light mounted next to the

DeviceNet connector provides status information on the communication link.

MITSUBISHI ELECTRIC AUTOMATION

Figure 1-1. FR-A5ND Option Unit

TOP VIEW

Mounting

Hole

DeviceNet

Connector

Status LED

Mounting

Hole

Station

Number

Switches

Status LED

DeviceNet Connector

Station Number Switches

Connector to

Inverter

Mounting

Holes

FR-A5ND

DeviceNet

Communications Option Unit

2. INSTALLATION

Installation requires the removal of the VFD cover. The VFD top cover must

be removed to install the option unit. After installation, the top cover is rein-

stalled and connection to the DeviceNet bus is completed through a connec-

tor accessible through the top cover.

WARNING: Cover removal can expose charged components. Be sure the

proper procedures are followed when removing cover.

Remove cover following the procedure in the VFD manual.

2.1. Pre-Installation checks

dedulcnigniwollofehttahtyfireV .deilppuserastnenopmoc tinUnoitpODN5A-RF.1 8x3MswercsgnitnuomowT.2 )502M698PSV( launaMnoitcurtsnI.3

.epytDFVehtyfireVotdengisedsitinunoitposihT seireS)L(005Aehthtiwkrow .)DFV(evirDycneuqerFelbairaV htiwtinusihtesuottpmettatonoD ,002A,001A.g.e(DFVrehtoyna sledomesehT.)seireSEdna,F,Z rotcennocnoitpotnereffidaesu ehtsecrofresuehtfidna ebyamDFVeht,rotcennoc .degamad

rewoptupniDFVehttahterusnE .ffodenrutsi tinunoitpoehtro/dnaDFVehT htiwdellatsnifidegamadebyam nasmrofrepDFVehT.norewop norewoptaerudecorpnoitazilaitini noitpoehtgnikcehcsedulcnitaht retalnoitpoehtgniddA.trop hcihwtcilfnocerawdrahasesuac ."3PO.E"mralaehtnitluserlliw roDFVehtegamadyamdnA .tinunoitpo

MITSUBISHI ELECTRIC AUTOMATION

2.2. Installation Procedure

Mounting Option Unit In VFD Option Port #3.

1. Verify that power has been turned off and that the VFD top cover has

been removed.

NOTE: The FR-A5ND option unit must be installed in Option Port #3 only.

An attempt to install in any other port may cause the VFD or the

option unit to be damaged.

2. Using the two mounting holes for alignment reference, carefully insert

the option unit connector into the VFD connector as shown in Figure 2-

1 and firmly press the unit into place.

NOTE: If screw holes in option unit do not line up with the VFD mounting

holes, check that connector has been correctly fitted.

3. Secure the option unit to the VFD with the two mounting screws.

4. Option unit is now mechanically installed as shown in Figure 2-2.

Figure 2-1. Option Unit aligned with Option Port #3

VSP896M205

3 x 8 mm Machine Screws

with Flat and Lock Washer

FR-A5ND Plug-in Option

Option to VFD

Connector

Mitsubishi

Inverter

VFD Option

Port 3

Machine Screw Inserts

Otros manuales de Unidad de control de Mitsubishi

Mitsubishi

Mitsubishi MELSEC A1S64AD Manual de usuario

Mitsubishi

Mitsubishi Q68TD-G-H01 Manual de usuario

Mitsubishi

Mitsubishi A1S62TCRTBW-S2 Manual de usuario

Mitsubishi

Mitsubishi MELSEC-A AJ71DN91 Manual de usuario

Mitsubishi

Mitsubishi A1SD75M3 Manual de usuario

Mitsubishi

Mitsubishi MELSEC-A series Manual de usuario

Mitsubishi

Mitsubishi MELSEC System Q Manual de usuario

Mitsubishi

Mitsubishi MELSEC Q Series Manual de usuario

Mitsubishi

Mitsubishi MELSEC L Series Manual de usuario

Mitsubishi

Mitsubishi Wi-Fi Control Manual de usuario

Mitsubishi

Mitsubishi MELSECNET/10 A1SJ72QLP25 Manual de usuario

Mitsubishi

Mitsubishi Q62HLC Manual de usuario

Mitsubishi

Mitsubishi MELDAS MDS-C1 Manual de usuario

Mitsubishi

Mitsubishi FX1N-5DM Manual de usuario

Mitsubishi

Mitsubishi MELSEC-A A1SJ71PB93D Manual de usuario

Mitsubishi

Mitsubishi QJ71AS92 Instrucciones de uso

Mitsubishi

Mitsubishi L Series Manual de usuario

Mitsubishi

Mitsubishi Q64AD Manual de usuario

Mitsubishi

Mitsubishi QD75M1 Manual de usuario

Mitsubishi

Mitsubishi NZ2GF2B-60DA4 Manual de usuario

Mitsubishi

Mitsubishi AJ65SBT2B-64AD Manual de usuario

Mitsubishi

Mitsubishi AL-ASI-BD Manual de usuario

Mitsubishi

Mitsubishi FX3U-ENET-ADP Manual de usuario

Mitsubishi

Mitsubishi MELSEC System Q Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario