Mitsubishi NZ2GF2B-60DA4 Manual de usuario

SAFETY PRECAUTIONS

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals carefully and pay full attention

to safety to handle the product correctly.

The precautions given in this manual are concerned with this product only. For the safety precautions of the

programmable controller system, refer to the user's manual for the CPU module used.

In this manual, the safety precautions are classified into two levels: " WARNING" and " CAUTION".

Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to

serious consequences.

Observe the precautions of both levels because they are important for personal and system safety.

Make sure that the end users read this manual and then keep the manual in a safe place for future

reference.

[Design Precautions]

WARNING

●In the case of a communication failure in the network, data in the master module are held. Check Data

link status (each station) (SW00B0 to SW00B7) and configure an interlock circuit in the program to

ensure that the entire system will operate safely.

●Do not use any "use prohibited" signals as a remote input or output signal. These signals are reserved

for system use. Do not write any data to the "use prohibited" area in the remote register. If these

operations are performed, correct operation of the module cannot be guaranteed.

●Configure safety circuits external to the programmable controller to ensure that the entire system

operates safely even when a fault occurs in the external power supply or the programmable controller.

Failure to do so may result in an accident due to an incorrect output or malfunction.

(1) The status of analog output depends on the setting of various functions that control the analog

output. Exercise great caution when setting those functions. For details of analog output status,

refer to the Page 76, Section 8.4.

(2) Due to failure of the output element or internal circuit, normal output may not be obtained

correctly. Configure an external circuit for monitoring output signals that could cause a serious

accident.

WARNING

CAUTION

Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,

resulting in minor or moderate injury or property damage.

[Design Precautions]

[Installation Precautions]

[Wiring Precautions]

CAUTION

●Do not install the control lines or communication cables together with the main circuit lines or power

cables. Keep a distance of 100mm or more between them. Failure to do so may result in malfunction

due to noise.

●At power-on or power-off, a voltage may occur or a current may flow between output terminals for a

moment. In this case, start the control after analog outputs become stable.

WARNING

●Shut off the external power supply (all phases) used in the system before mounting or removing a

module. Failure to do so may result in electric shock or cause the module to fail or malfunction.

CAUTION

●Use the module in an environment that meets the general specifications in this manual. Failure to do

so may result in electric shock, fire, malfunction, or damage to or deterioration of the product.

●Securely fix the module with a DIN rail.

●Do not directly touch any conductive parts and electronic components of the module. Doing so can

cause malfunction or failure of the module.

●After the first use of the product (extension module), the number of connections/disconnections is

limited to 50 times (IEC 61131-2 compliant).

●To connect an extension module to a main module, engage the respective connectors and securely

lock the module joint levers. Incorrect connection may cause malfunction, failure, or drop of the

module.

●Securely connect the cable connectors. Poor contact may cause malfunction.

WARNING

●Shut off the external power supply (all phases) used in the system before wiring. Failure to do so may

result in electric shock or cause the module to fail or malfunction.

CAUTION

●Individually ground the FG terminal of the programmable controller with a ground resistance of 100Ω

or less. Failure to do so may result in electric shock or malfunction.

●Tighten any unused terminal screws within the specified torque range. Undertightening may cause a

short circuit due to contact with a solderless terminal.

[Wiring Precautions]

[Startup and Maintenance Precautions]

CAUTION

●Use applicable solderless terminals and tighten them within the specified torque range. If any spade

solderless terminal is used, it may be disconnected when a terminal block screw comes loose,

resulting in failure.

●Check the rated voltage and terminal layout before wiring to the module, and connect the cables

correctly. Connecting a power supply with a different voltage rating or incorrect wiring may cause a fire

or failure.

●Tighten the terminal block screws within the specified torque range. Undertightening can cause short

circuit, fire, or malfunction. Overtightening can damage the screw and/or module, resulting in drop,

short circuit, fire, or malfunction.

●Prevent foreign matter such as dust or wire chips from entering the module. Such foreign matter can

cause a fire, failure, or malfunction.

●Place the cables in a duct or clamp them. If not, dangling cable may swing or inadvertently be pulled,

resulting in damage to the module or cables or malfunction due to poor contact.

●Do not install the control lines or communication cables together with the main circuit lines or power

cables. Keep a distance of 100mm or more between them. Failure to do so may result in malfunction

due to noise.

●When disconnecting the cable from the module, do not pull the cable by the cable part. For the cable

with connector, hold the connector part of the cable. For the cable connected to the terminal block,

loosen the terminal screw. Pulling the cable connected to the module may result in malfunction or

damage to the module or cable.

●When an overcurrent caused by an error of an external device or a failure of the programmable

controller flows for a long time, it may cause smoke and fire. To prevent this, configure an external

safety circuit, such as a fuse.

●Mitsubishi programmable controllers must be installed in control panels. Wiring and replacement of a

module must be performed by qualified maintenance personnel with knowledge of protection against

electric shock. For wiring methods, refer to "INSTALLATION AND WIRING" in this manual.

WARNING

●Do not touch any terminal while power is on. Doing so will cause electric shock or malfunction.

●Shut off the external power supply (all phases) used in the system before cleaning the module or

retightening the terminal block screws. Failure to do so may cause the module to fail or malfunction.

CAUTION

●Do not disassemble or modify the module. Doing so may cause failure, malfunction, injury, or a fire.

●Do not drop or apply strong shock to the module. Doing so may damage the module.

●Shut off the external power supply (all phases) used in the system before mounting or removing a

module. Failure to do so may cause the module to fail or malfunction.

[Startup and Maintenance Precautions]

[Disposal Precautions]

CAUTION

●After the first use of the product (terminal block), the number of connections/disconnections is limited

to 50 times (IEC 61131-2 compliant).

●Before handling the module or the cable to be connected to the module, touch a conducting object

such as a grounded metal to discharge the static electricity from the human body. Failure to do so may

cause the module to fail or malfunction.

●Startup and maintenance of a control panel must be performed by qualified maintenance personnel

with knowledge of protection against electric shock. Lock the control panel so that only qualified

maintenance personnel can operate it.

CAUTION

●When disposing of this product, treat it as industrial waste.

CONDITIONS OF USE FOR THE PRODUCT

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major

or serious accident; and

ii) where the backup and fail-safe function are systematically or automatically provided outside of

the PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general

industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT

LIMITED TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT,

WARRANTY, TORT, PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR

LOSS OR DAMAGE TO PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR

USED IN APPLICATION NOT INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS,

OR WARNING CONTAINED IN MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY

MANUALS, TECHNICAL BULLETINS AND GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

• Nuclear Power Plants and any other power plants operated by Power companies, and/or any

other cases in which the public could be affected if any problem or fault occurs in the PRODUCT.

• Railway companies or Public service purposes, and/or any other cases in which establishment of

a special quality assurance system is required by the Purchaser or End User.

• Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as

Elevator and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation,

Equipment for Recreation and Amusement, and Safety devices, handling of Nuclear or

Hazardous Materials or Chemicals, Mining and Drilling, and/or other applications where there is a

significant risk of injury to the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the

PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT

is limited only for the specific applications agreed to by Mitsubishi and provided further that no

special quality assurance or fail-safe, redundant or other safety features which exceed the general

specifications of the PRODUCTs are required. For details, please contact the Mitsubishi

representative in your region.

INTRODUCTION

Thank you for purchasing the CC-Link IE Field Network D/A converter module (hereafter abbreviated as D/A converter

module).

This manual describes the operating procedure, system configuration, parameter settings, functions, and

troubleshooting of the D/A converter module.

Before using this product, please read this manual and the relevant manuals carefully and develop familiarity with the

functions and performance of the D/A converter module to handle the product correctly.

When applying the program examples introduced in this manual to an actual system, ensure the applicability and

confirm that it will not cause system control problems.

Target module: NZ2GF2B-60DA4

Remark

Unless otherwise specified, this manual describes the program examples in which the remote I/O signals and remote

registers are assigned for a D/A converter module as follows.

• Remote input signal: RX0 to RX1F

• Remote output signal: RY0 to RY1F

• Remote register: RWr0 to RWrF, RWw0 to RWwF

For the assignment of remote I/O signals and remote registers, refer to the following.

User's manual for the master/local module used

RELEVANT MANUALS

(1) CC-Link IE Field Network (relevant) manuals

When using the CC-Link IE Field Network for the first time, refer to CC-Link IE Field Network Master/Local

Module User's Manual first. The following shows the structure of the CC-Link IE Field Network manuals.

(2) Operating manual

Manual name

<manual number (model code)> Description

MELSEC-Q CC-Link IE Field Network Master/Local Module User's

Manual

<SH-080917ENG, 13JZ47>

Overview of the CC-Link IE Field Network, and specifications,

procedures before operation, system configuration, installation,

wiring, settings, functions, programming, and troubleshooting of

the QJ71GF11-T2

MELSEC-L CC-Link IE Field Network Master/Local Module User's

Manual

<SH-080972ENG, 13JZ54>

Overview of the CC-Link IE Field Network, and specifications,

procedures before operation, system configuration, installation,

wiring, settings, functions, programming, and troubleshooting of

the LJ71GF11-T2

Manual name

<manual number (model code)> Description

GX Works2 Version1 Operating Manual (Common)

<SH-080779ENG, 13JU63>

System configuration, parameter settings, and online

operations of GX Works2, which are common to Simple projects

and Structured projects

CONTENTS

SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

CONDITIONS OF USE FOR THE PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

RELEVANT MANUALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

MANUAL PAGE ORGANIZATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

TERM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

PACKING LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

CHAPTER 1 D/A CONVERTER MODULE 15

1.1 Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

CHAPTER 2 PART NAMES 19

CHAPTER 3 SPECIFICATIONS 23

3.1 General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.2 Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3.3 Calculating Current Consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

3.4 Function List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

3.5 List of Remote I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

3.6 List of Remote Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

3.7 List of Remote Buffer Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

CHAPTER 4 THE PROCEDURE BEFORE OPERATION 41

CHAPTER 5 SYSTEM CONFIGURATION 43

5.1 D/A Converter Module System Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

5.2 Applicable Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

CHAPTER 6 INSTALLATION AND WIRING 45

6.1 Station Number Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

6.2 Installation Environment and Installation Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

6.2.1 Installation environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

6.2.2 Installation position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

6.2.3 Installation direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

6.3 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

6.3.1 Connecting extension modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

6.3.2 Mounting the modules on a DIN rail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

6.4 Wiring with Terminal Block for Module Power Supply and FG . . . . . . . . . . . . . . . . . . . . . . . . . 52

6.5 Wiring of Ethernet Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

6.6 Wiring of External Device and Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Tabla de contenidos

Otros manuales de Unidad de control de Mitsubishi

Mitsubishi

Mitsubishi MELSEC-A A1S68AD Manual de usuario

Mitsubishi

Mitsubishi MELSEC Q Series Manual de usuario

Mitsubishi

Mitsubishi MELSEC L Series Manual de usuario

Mitsubishi

Mitsubishi FX2N Manual de usuario

Mitsubishi

Mitsubishi Q62HLC Manual de usuario

Mitsubishi

Mitsubishi L Series Manual de usuario

Mitsubishi

Mitsubishi A1S62TCRTBW-S2 Manual de usuario

Mitsubishi

Mitsubishi MELSEC-A A1SJ71PB93D Manual de usuario

Mitsubishi

Mitsubishi FR-A5ND Manual de usuario

Mitsubishi

Mitsubishi MELSEC System Q Manual de usuario

Mitsubishi

Mitsubishi QJ71AS92 Instrucciones de uso

Mitsubishi

Mitsubishi MELSEC-F FX2N Series Manual de usuario

Mitsubishi

Mitsubishi A1SJ71AP21 Manual de usuario

Mitsubishi

Mitsubishi A0J2CPU Manual de usuario

Mitsubishi

Mitsubishi Q68RD3-G Manual de usuario

Mitsubishi

Mitsubishi MELSEC Q Series Manual de usuario

Mitsubishi

Mitsubishi MELSEC QJ71C24N Manual de usuario

Mitsubishi

Mitsubishi MELSEC-Q QD77MS Manual de usuario

Mitsubishi

Mitsubishi AL-ASI-BD Manual de usuario

Mitsubishi

Mitsubishi QJ71WS96 Series Manual de usuario

Mitsubishi

Mitsubishi MELSEC-A series Manual de usuario

Mitsubishi

Mitsubishi Q68TD-G-H01 Manual de usuario

Mitsubishi

Mitsubishi M800S series Guía de configuración

Mitsubishi

Mitsubishi AJ65SBT2B-64AD Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario