Milwaukee MW100 Manual de usuario

SPECIFICATIONS:

MW100

RANGE 0.0 to 14.0 pH

RESOLUTION 0.1 pH

ACCURACY (@25°C) ±0.2 pH

TYPICAL EMC DEVIATION ±0.1 pH

pH ELECTRODE SE220 (included)

ENVIRONMENT 0 to 50°C, 95% RH max.

BATTERY TYPE 1 x 9V alkaline (included)

BATTERY LIFE approximately 300 hours of use

DIMENSIONS 143 x 80 x 32 mm

WEIGHT 220 g (with battery) meter only

OPTIONAL ACCESSORIES:

M10004B pH 4.01 buffer solution, 20 mL sachet (25 pcs)

M10007B pH 7.01 buffer solution, 20 mL sachet (25 pcs)

M10010B pH 10.01 buffer solution, 20 mL sachet (25 pcs)

M10000B Electrode rinse solution, 20 mL sachet (25 pcs)

MA9015 Electrode storage solution, 220 mL bottle

SE220 pH electrode with BNC connector and 1 m cable

MA950 Portable meter wall mounting kit

WARRANTY:

This instrument is warranted from all defects in materials and

manufacturing for a period of two years from the date of purchase.

The electrode is warranted for a period of six months.

If during this period, the repair or replacement of parts is required,

where the damage is not due to negligence or erroneous operation by

the user, please return the parts to either dealer or our office and the

repair will be effected free of charge.

Note: We reserve the right to modify the design, construction and

appearance of our products without advance notice.

USER MANUAL

PORTABLE

pH METER

MODEL: MW100

OPERATION:

• The meter is supplied complete with a

9V battery. Slide off the battery

compartment cover on the back of the

meter. Install the battery into the battery

clip connector while observing polarity.

• Always remove the electrode

protective cap before taking any

measurement. If the electrode has been

left dry, soak the tip (bottom 2.5 cm) in

rinse solution (M10000B) for a few

minutes to reactivate it.

• Connect the pH electrode to the BNC socket on the top of

the meter.

• Make sure that the meter has been calibrated before taking

any measurements (see Calibration Procedure).

• Immerse the tip (2.5 cm) of the pH electrode into the sample.

• Turn the instrument on by pressing the ON/OFF key.

• Allow the reading to stabilize before taking measurements.

• After measurements, switch the meter off and store the

electrode with a few drops of storage solution

(MA9015) in the protective cap.

CALIBRATION PROCEDURE:

• Remove the protective cap from the electrode.

• Rinse tip off with distilled water or a small

quantity of pH 7.

• Immerse the electrode tip into a new sachet

of pH7 calibration solution and allow the reading

to stabilize.

• Adjust the pH7 (OFFSET) calibration trimmer to

display "7.0 pH".

• Open a new sachet of pH4 calibration solution

and use a small quantity to rinse the electrode.

• Immerse the electrode tip inside the pH4 sachet

and allow the reading to stabilize.

• Adjust the pH4/pH10 (SLOPE) calibration

trimmer to read "4.0 pH".

• The calibration is now complete and the

meter is ready to take measurements.

• It is suggested the meter be calibrated at least

once a month, after a prolonged period of

inactivity, and after electrode replacement.

BATTERY REPLACEMENT:

When the battery becomes weak the meter

will display " ".

When the low battery indicator appears, the

battery has only about 50 hours of working

time left. A low battery will result in

unreliable measurements.

Prompt battery replacement is required.

Battery replacement must only take place in

a non-hazardous area using an alkaline 9V

battery.

Turn the meter off, slide the battery

compartment cover located at the rear of the

meter off and replace the 9V battery with a

new one. Make sure the battery contacts are fully engaged in

the connector, seat the battery in its compartment and replace

the cover.

Otros manuales de Instrumento de medición de Milwaukee

Milwaukee

Milwaukee Smart PH Meter Manual de usuario

Milwaukee

Milwaukee MW102 Manual de usuario

Milwaukee

Milwaukee MI 411 Manual de usuario

Milwaukee

Milwaukee 2217-40 Manual de usuario

Milwaukee

Milwaukee pH52 Manual de usuario

Milwaukee

Milwaukee HEAVY DUTY M12 PL Manual de usuario

Milwaukee

Milwaukee 3712 Manual de usuario

Milwaukee

Milwaukee MW13 Manual de usuario

Milwaukee

Milwaukee 48-22-9801 Manual de usuario

Milwaukee

Milwaukee LDM 45 Manual de usuario

Milwaukee

Milwaukee 2235-40 Manual de usuario

Milwaukee

Milwaukee Mi 180 Manual de usuario

Milwaukee

Milwaukee MI806 Manual de usuario

Milwaukee

Milwaukee MW100 Manual de usuario

Milwaukee

Milwaukee Mi453 Manual de usuario

Milwaukee

Milwaukee PH55 Manual de usuario

Milwaukee

Milwaukee MW170 MAX Manual de usuario

Milwaukee

Milwaukee MW11 Manual de usuario

Milwaukee

Milwaukee MA871 Manual de usuario

Milwaukee

Milwaukee REDSTICK MLDIG14 Manual de usuario

Milwaukee

Milwaukee pH600 Manual de usuario

Milwaukee

Milwaukee MW11 Manual de usuario

Milwaukee

Milwaukee MA886 Manual de usuario

Milwaukee

Milwaukee PST MW12 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario