Milwaukee MW13 Manual de usuario

SPECIFICATIONS

Range 0.0 to 12.5 ppm

Resolution 0.1 ppm

Accuracy ±0.1 ppm ±5% of reading

@ 25 °C

Typical EMC Dev. ±0.1 ppm

Light Source Light Emitting Diode

@525nm

Light Detector Silicon Photocell

Method

Adaptation of the Standard

Methods for the Examination

of Water and Wastewater,

18th edition, DPD method. The

reaction between iodine and

the reagent causes a pink

tint in the sample.

Environment 0 to 50°C (32 to 122 °F)

max. 95% RH non-condensing

Battery Type 1 x 1.5V AAA

Auto-Shut O After 5min. of non-use and

2min. after reading.

Dimensions 87.5 x 63.7 x 35.2 mm

(3.4 x 2.5 x 1.4”)

Weight 65 g (2.29 oz.)

OPTIONAL ACCESSORIES

Reagent Sets

MI527-25 Iodine powder reagent (25pcs.)

Other Accessories

MI0011 Glass cuvettes (2 pcs.)

MI0013 Stoppers for cuvettes (2 pcs.)

USER MANUAL

milwaukeeinstruments.com (USA & CAN)

milwaukeeinstruments.eu

MW13 Digital

Iodine Tester

1.3

ppm

Iodine

MW13

SATISFACTION

GUARANTEED

ISTMW13 04/21

CERTIFICATION

Milwaukee Instruments conform to the

CE European Directives.

Disposal of Electrical & Electronic

Equipment. Do not treat this product

as household waste. Hand it over to

the appropriate collection point for the

recycling of electrical and electronic

equipment.

Disposal of waste batteries. This product

contains batteries. Do not dispose of them with

other household waste. Hand them over to the

appropriate collection point for recycling.

Please note: proper product and battery disposal

prevents potential negative consequences

for human health and the environment. For

detailed information, contact your local

household waste disposal service or go to

www.milwaukeeinstruments.com (USA & CAN)

or www.milwaukeeinstruments.eu.

RECOMMENDATION

Before using this product, make sure it is entirely

suitable for your specific application and for the

environment in which it is used. Any modification

introduced by the user to the supplied equipment

may compromise the tester’s performance. For

your and the tester’s safety do not use or store

the tester in hazardous environment. To avoid

damage or burn, do not perform any measurement

in microwave ovens.

WARRANTY

This tester is warranted against defects in

materials and manufacturing for a period of

2years from the date of purchase. This warranty

is limited to repair or free of charge replacement

if the tester cannot be repaired. Damage due to

accidents, misuse, tampering or lack of prescribed

maintenance is not covered by warranty. If

service is required, contact your local Milwaukee

Instruments Technical Service. If the repair is not

covered by the warranty, you will be notified of

the charges incurred. When shipping any tester,

make sure it is properly packaged for complete

protection.

Milwaukee Instruments reserves the right to

make improvements in design, construction and

appearance of its products without advance notice.

PRELIMINARY EXAMINATION

ThankyouforchoosingMilwaukee Instruments!

Remove the tester and accessories from the

packing and examine it carefully.

For further support please contact your closest

Milwaukee Instruments oice.

Each MW13 tester is supplied complete with:

ySample cuvette and cap (2 pcs.)

yIodine powder reagents (6 tests)

y1 x 1.5V AAA Battery

yInstruction manual

FUNCTIONAL DESCRIPTION

Iodine

W13

1. Dust cover

2. Cuvette with cap

3. Cuvette holder

4. Liquid Crystal Display

5. On/O button

OPERATION

yPress the On/O button to turn the tester on.

All segments are displayed for a few

seconds followed by “Add”, “C1” with “Press”

blinking.

yFill the cuvette with 10 mL of unreacted

sample and replace the cap. Place the

cuvette into the tester and close the cap.

yPress the On/O button. When the display

shows “Add”, “C.2” with “Press” blinking, the

tester is zeroed.

yRemove the cuvette, unscrew the cap and

add the content of one packet of MI527-0

reagent. Replace the cap and shake gently

for 20seconds until the powder is completely

dissolved. Replace the cuvette into the tester.

yPress and hold the On/O button.

The display will show the countdown prior

to the measurement.

Alternatively, wait 2minutes and 30seconds

and press the On/O button.

yWhen the timer ends the tester will perform

the reading. The tester directly displays the

concentration of iodine in ppm.

The tester automatically turns o 2minutes

after reading.

BATTERY REPLACEMENT

To save the battery, the tester shuts down

after 5 minutes of non-use and 2 minutes

after reading. A fresh battery lasts for a

minimum of 5000 measurements, depending

on the light level.

When the battery capacity is under 10%, the

tester displays “bAt” at start up.

When the battery is drained the tester

display’s “bAd” then “bAt” message.

Replace the battery with a new one and restart

the tester.

ppm

Iodine

MW13

To replace the battery, follow the steps:

yPress the On/O button to turn the tester o.

yTurn the tester upside down and use a

screwdriver to unfasten the screw and

remove the battery cover.

yRemove the old battery and replace it

with a fresh 1.5V AAA battery, inserting the

negative end first.

yReplace the battery cover, fasten and

tighten the screw.

Otros manuales de Instrumento de medición de Milwaukee

Milwaukee

Milwaukee M12 3PLA Manual de usuario

Milwaukee

Milwaukee PST MW100 PRO Manual de usuario

Milwaukee

Milwaukee LDM 45 Manual de usuario

Milwaukee

Milwaukee MA887 Manual de usuario

Milwaukee

Milwaukee MW12 Manual de usuario

Milwaukee

Milwaukee SM101 Manual de usuario

Milwaukee

Milwaukee MW105 MAX Manual de usuario

Milwaukee

Milwaukee MW11 Manual de usuario

Milwaukee

Milwaukee MAX MW160 Manual de usuario

Milwaukee

Milwaukee M12 SUB-SCANNER 2291-20 Manual de usuario

Milwaukee

Milwaukee M12 CLLP-301C Manual de usuario

Milwaukee

Milwaukee PRO MW801 Manual de usuario

Milwaukee

Milwaukee MI490 Manual de usuario

Milwaukee

Milwaukee M12 AL Manual de usuario

Milwaukee

Milwaukee pH600 Manual de usuario

Milwaukee

Milwaukee MC110 Manual de usuario

Milwaukee

Milwaukee HEAVY DUTY M12 PL Manual de usuario

Milwaukee

Milwaukee MI605 Manual de usuario

Milwaukee

Milwaukee Mi 180 Manual de usuario

Milwaukee

Milwaukee 48-22-9801 Manual de usuario

Milwaukee

Milwaukee CALIBRATION 2238-20 Manual de usuario

Milwaukee

Milwaukee Smart PH Meter Manual de usuario

Milwaukee

Milwaukee MW101 Manual de usuario

Milwaukee

Milwaukee MA871 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario