Milwaukee Smart PH Meter Manual de usuario

Milwaukee

USER MANUAL

PORTABLE

pH METER

MODEL: SM100

Smart pH Meter

ISMIL100 11/01

SPECIFICATIONS:

SM100

RANGE 0.0 to 14.0 pH

RESOLUTION 0.1 pH

ACCURACY (@25°C) ±0.2 pH

pH ELECTRODE MA911B/1 (included)

ENVIRONMENT 0 to 50°C, 95% RH max.

BATTERY TYPE 1 x 9V alkaline (included)

BATTERY LIFE approximately 300 hours of use

DIMENSIONS 145 x 80 x 40 mm

WEIGHT 220 g (with battery) meter only

OPTIONAL ACCESSORIES:

M10004B pH 4.01 buffer solution, 20 ml sachet (25 pcs)

M10007B pH 7.01 buffer solution, 20 ml sachet (25 pcs)

M10010B pH 10.01 buffer solution, 20 ml sachet (25 pcs)

M10000B Electrode rinse solution, 20 ml sachet (25 pcs)

MA9015 Electrode storage solution, 220 ml bottle

MA911B/1 pH-electrode with BNC connector and 1 m cable

MA950 Portable meter wall fixing kit

WARRANTY:

This instrument is warranted from all defects in materials and manufacturing for

a period of two years from the date of purchase.

The electrode is warranted for a period of 6 months.

If during this period, the repair or replacement of parts is required, where the

damage is not due to negligence or erroneous operation by the user, please return

the parts to either dealer or our office and the repair will be effected free of

charge.

Note: We reserve the right to modify the design, construction and appearance

of our products without advance notice.

Milwaukee

OPERATION:

• The meter is supplied complete with

a 9V battery. Slide off the battery com-

partment cover on the back of the

meter. Install the battery while paying

attention to its polarity.

• Always remove the electrode protective

cap before taking any measurement. If

the electrode has been left dry, soak

the tip (bottom 2.5 cm) in rinse solu-

tion (M10000B) for a few minutes to

reactivate it.

• Connect the pH electrode to the BNC

socket on the top of the meter.

• Make sure that the meter has been

calibrated before taking any measure-

ments (see Calibration Procedure)

• Immerse the tip (2.5 cm) of the pH

electrode into the sample.

• Turn the instrument on by pressing the ON/OFF key.

• Allow the reading to stabilize before taking mea-

surements.

• After measurements, switch the meter off and

store the electrode with a few drops of storage

solution in the protective cap.

CALIBRATION PROCEDURE:

• Remove the protective cap from the electrode.

• Immerse the electrode tip into a new sachet of

pH7 calibration solution and allow the reading

to stabilize.

• Adjust the pH7 (OFFSET) calibration knob to

display "7.0 pH".

• Open a new sachet of pH4 cali-

bration solution and use a small

quantity to rinse the electrode.

• Immerse the electrode tip inside

the pH4 sachet and allow the read-

ing to stabilize.

• Adjust the pH4/pH10 (SLOPE) cali-

bration knob to read "4.0 pH".

• The calibration is now complete and the meter is ready to

take measurements.

• It is suggested to recalibrate the meter at least once a

month, after a prolonged stocking time and after electrode

replacement.

BATTERY REPLACEMENT:

When the battery becomes weak the

meter will display "V".

When the low battery indicator appears,

the battery has only about 50 hours of

working time left. A low battery will result

in unreliable measurements. It is recom-

mended to replace immediately the

battery.

Battery replacement must only take place

in a non-hazardous area using an alka-

line 9V battery.

Turn the meter off, slide off the battery

compartment cover at the rear of the meter

and replace the 9V battery with a new

one. Make sure the battery contacts are

tight and secure, seat the battery in its

compartment and insert the cover again.

OPERATION:

• The meter is supplied complete with

a 9V battery. Slide off the battery com-

partment cover on the back of the

meter. Install the battery while paying

attention to its polarity.

• Always remove the electrode protective

cap before taking any measurement. If

the electrode has been left dry, soak

the tip (bottom 2.5 cm) in rinse solu-

tion (M10000B) for a few minutes to

reactivate it.

• Connect the pH electrode to the BNC

socket on the top of the meter.

• Make sure that the meter has been

calibrated before taking any measure-

ments (see Calibration Procedure)

• Immerse the tip (2.5 cm) of the pH

electrode into the sample.

• Turn the instrument on by pressing the ON/OFF key.

• Allow the reading to stabilize before taking mea-

surements.

• After measurements, switch the meter off and

store the electrode with a few drops of storage

solution in the protective cap.

CALIBRATION PROCEDURE:

• Remove the protective cap from the electrode.

• Immerse the electrode tip into a new sachet of

pH7 calibration solution and allow the reading

to stabilize.

• Adjust the pH7 (OFFSET) calibration knob to

display "7.0 pH".

• Open a new sachet of pH4 cali-

bration solution and use a small

quantity to rinse the electrode.

• Immerse the electrode tip inside

the pH4 sachet and allow the read-

ing to stabilize.

• Adjust the pH4/pH10 (SLOPE) cali-

bration knob to read "4.0 pH".

• The calibration is now complete and the meter is ready to

take measurements.

• It is suggested to recalibrate the meter at least once a

month, after a prolonged stocking time and after electrode

replacement.

BATTERY REPLACEMENT:

When the battery becomes weak the

meter will display "V".

When the low battery indicator appears,

the battery has only about 50 hours of

working time left. A low battery will result

in unreliable measurements. It is recom-

mended to replace immediately the

battery.

Battery replacement must only take place

in a non-hazardous area using an alka-

line 9V battery.

Turn the meter off, slide off the battery

compartment cover at the rear of the meter

and replace the 9V battery with a new

one. Make sure the battery contacts are

tight and secure, seat the battery in its

compartment and insert the cover again.

Milwaukee

USER MANUAL

PORTABLE

pH METER

MODEL: SM100

Smart pH Meter

ISMIL100 11/01

SPECIFICATIONS:

SM100

RANGE 0.0 to 14.0 pH

RESOLUTION 0.1 pH

ACCURACY (@25°C) ±0.2 pH

pH ELECTRODE MA911B/1 (included)

ENVIRONMENT 0 to 50°C, 95% RH max.

BATTERY TYPE 1 x 9V alkaline (included)

BATTERY LIFE approximately 300 hours of use

DIMENSIONS 145 x 80 x 40 mm

WEIGHT 220 g (with battery) meter only

OPTIONAL ACCESSORIES:

M10004B pH 4.01 buffer solution, 20 ml sachet (25 pcs)

M10007B pH 7.01 buffer solution, 20 ml sachet (25 pcs)

M10010B pH 10.01 buffer solution, 20 ml sachet (25 pcs)

M10000B Electrode rinse solution, 20 ml sachet (25 pcs)

MA9015 Electrode storage solution, 220 ml bottle

MA911B/1 pH-electrode with BNC connector and 1 m cable

MA950 Portable meter wall fixing kit

WARRANTY:

This instrument is warranted from all defects in materials and manufacturing for

a period of two years from the date of purchase.

The electrode is warranted for a period of 6 months.

If during this period, the repair or replacement of parts is required, where the

damage is not due to negligence or erroneous operation by the user, please return

the parts to either dealer or our office and the repair will be effected free of

charge.

Note: We reserve the right to modify the design, construction and appearance

of our products without advance notice.

Milwaukee

Tabla de contenidos

Otros manuales de Instrumento de medición de Milwaukee

Milwaukee

Milwaukee MW101 Manual de usuario

Milwaukee

Milwaukee MI 806 Manual de usuario

Milwaukee

Milwaukee M12 3632-20 Manual de usuario

Milwaukee

Milwaukee 2010R Manual de usuario

Milwaukee

Milwaukee MC310 Manual de usuario

Milwaukee

Milwaukee 2217-40 Manual de usuario

Milwaukee

Milwaukee HEAVY DUTY M12 PL Manual de usuario

Milwaukee

Milwaukee MI 413 Manual de usuario

Milwaukee

Milwaukee 2217-40 Manual de usuario

Milwaukee

Milwaukee MAX MW160 Manual de usuario

Milwaukee

Milwaukee M12 SPL Manual de usuario

Milwaukee

Milwaukee 2205-20 Manual de usuario

Milwaukee

Milwaukee M12 CLLP-301C Manual de usuario

Milwaukee

Milwaukee MW102 Manual de usuario

Milwaukee

Milwaukee PST MW12 Manual de usuario

Milwaukee

Milwaukee MW500 Manual de usuario

Milwaukee

Milwaukee MW11 Manual de usuario

Milwaukee

Milwaukee LDM 80 Manual de usuario

Milwaukee

Milwaukee MW802 Manual de usuario

Milwaukee

Milwaukee PRO MW801 Manual de usuario

Milwaukee

Milwaukee MW301 Manual de usuario

Milwaukee

Milwaukee PRO Lux MW700 Manual de usuario

Milwaukee

Milwaukee PRO MI414 Manual de usuario

Milwaukee

Milwaukee MI411 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario