Metrologic S4800 microQuest Series Manual de usuario

METROLOGIC INSTRUMENTS, INC.

IS4800 microQuest®Series

Single-Line Scanning Engine

Installation Guide

work may be reproduced, transmitted, or stored in any form or by any means

without prior written consent, except by reviewer, who may quote brief

passages in a review, or provided for in the Copyright Act of 1976.

Products and brand names mentioned in this document are trademarks of

their respective companies.

TABLE OF CONTENTS

Introduction

Models and Accessories...................................................................................... 1

Components of the microQuest........................................................................ 2

Labels............................................................................................................... 2

Mounting Specifications

Scan Engine Dimensions ................................................................................. 3

Exit Beam Specifications.................................................................................. 4

Enclosure Specifications

Grounding..................................................................................................... 5

Magnetic Sensitivity...................................................................................... 5

Electrostatic Discharge (ESD) Cautions....................................................... 5

Printed Circuit Board Component Clearance................................................ 6

Airborne Contaminants and Foreign Materials ............................................. 6

Beam Clearance........................................................................................... 6

Output Window Properties............................................................................ 7

Output Window Coatings.............................................................................. 8

Output Window Angle................................................................................... 8

Depth of Field vs Minimum Bar Code Element................................................... 11

Design Specifications ......................................................................................... 12

Scan Engine Terminations

IS4813 Pinout Connections............................................................................ 14

IS4815 Pinout Connections............................................................................ 15

Scan Sense Timing

Timing Diagram .............................................................................................. 16

Scan Sense .................................................................................................... 16

Barcode Element Time Calculation ................................................................ 17

Laser and Product Safety

Regulatory Requirements............................................................................... 18

Europe............................................................................................................ 19

United States.................................................................................................. 20

iii

TABLE OF CONTENTS

Canada........................................................................................................... 21

Cautions ......................................................................................................... 22

Limited Warranty ................................................................................................ 23

Patents ............................................................................................................... 24

Index .................................................................................................................. 25

Contact Information and Office Locations........................................................... 27

INTRODUCTION

The IS4800 microQuest®series are miniature single-line scan engines designed

for direct integration into customer decode-equipped OEM devices.

The microQuest non-decode scan engine is equipped with a multitude of

features including:

•100 Scans per Second, Typical.

•Support for 3.3VDC Input Voltage (IS4813 Model)

•Support for 5VDC Input Voltage (IS4815 Model)

•A 650 nm Bright Laser Diode

•A narrow exit angle to provide precision beam positioning.

•Automatic (Hardware) Scan Sense

•A rugged industry standard size die cast chassis with threaded mounting

holes.

•A 10-pin ZIF Connector Industry Standard Pinout for Seamless Integration

into Portable Devices

•Low Mass (11 grams) Industry Standard Size

The manufacturer of the end equipment must register with agencies such

as the Food and Drug Administration (FDA). The specifications required

for registration are not obtainable until the OEM manufacturer uses the

microQuest Engine in its final configuration. Therefore, it becomes the

responsibility of the manufacturer who incorporates the scan engine into

their product to comply with all federal laser safety regulations.

The manufacturer must submit a Laser Product Report for the FDA in the

US. Metrologic will assist its customers in complying with the necessary

procedures.

THIS DEVICE DOES NOT COMPLY WITH 21 CFR 1040.

USE ONLY AS COMPONENT.

Caution: The laser is susceptible to permanent damage if enabled less

than 50 ms after the Scan Enable has been activated. This requirement

must be strictly adhered to or the limited warranty on page 23 is void.

Refer to Scan Sense Timing on pages 16 - 17 for additional information.

MODELS AND ACCESSORIES

Model Description

IS4813 Non-Decode, 3.3VDC Scan Engine

IS4815 Non-Decode, 5VDC Scan Engine

19-07335 10-pin Flex Cable

COMPONENTS OF THE MICROQUEST

Figure 1. IS4800 Series Components

ITEM NO. DESCRIPTION

 Pin Locator Holes (specifications on page 3)

 Threaded Mounting Points (specifications on page 3)



Exit Beam Location, Laser Light Aperture

AVOID EXPOSURE – LASER LIGHT

IS EMITTED FROM THIS APERTURE

 Die Cast Chassis

 10-Pin ZIF Connector

 Printed Circuit Board

LABELS

The serial number/model number label is located on engine chassis (see below).

Figure 2. Serial Number Label (Enlarged For Illustration Purposes)

MOUNTING SPECIFICATIONS

Scan Engine Dimensions

Figure 3. IS4800 Series Dimensions

Specifications are subject to change without notice.

MOUNTING SPECIFICATIONS

Exit Beam Specifications

Figure 4. IS4800 Series Exit Beam Specifications

Specifications are subject to change without notice.

MOUNTING SPECIFICATIONS

Enclosure Specifications

The IS4800 scan engine series was specifically designed for integration into

custom housings for OEM applications. The scan engine’s performance will be

adversely affected or permanently damaged when mounted in an unsuitable

enclosure.

THIS DEVICE DOES NOT COMPLY WITH 21 CFR 1040.

USE ONLY AS COMPONENT.

The limited warranty (on page 23) is void if the following

considerations are not adhered to when integrating the

IS4800 series scan engine into a system.

Grounding

If the scan engine is going to be installed in a grounded host:

•Use an insulator between the engine chassis and host. The die-cast

engine chassis is at +Vcc.

•Use shoulder washers to isolate the screws from the host if the mounting

screws are metallic.

Magnetic Sensitivity

The scan engine can be negatively affected by magnetic fields:

•Use only non-magnetic screws and locating pins.

•Do not mount the engine within 1.00" of any magnetic materials.

Electrostatic Discharge (ESD) Cautions

The scan engine has exposed electrical components.

•DO NOT touch the leads of the Visible Laser Diode (VLD) or other

components.

•ALWAYS use grounding wrist straps and a grounded work area when

handling the engine.

•Mount the engine in a housing that is designed for ESD protection and

stray electric fields.

ESD has the ability to modify the electrical characteristics of a

semiconductor device, possibly degrading or even destroying the

device. ESD also has the potential to upset the normal operation

of an electronic system, causing equipment malfunction or failure.

MOUNTING SPECIFICATIONS

Enclosure Specifications

Printed Circuit Board (PCB) Component Clearance

WARNING: When designing the IS4800 into the final product, be sure to eliminate

all possible means of shorting Resistors R3 and R25 in the IS4800.

A short could enable the scan engine to emit Class 3R radiation. Any

CDRH filing will require a disclosure of the design ensuring a method

to mitigate a potential short.

Figure 5. IS4800 PCB Clearence Warning

Airborne Contaminants and Foreign Materials

The scan engine has very sensitive miniature electrical and optical

components that must be protected from airborne contaminants and foreign

materials. In order to prevent permanently damaging the scan engine and

voiding the limited warranty (on page 23), the scan engine enclosure must be:

•Sealed to prevent infiltration by airborne contaminants and foreign

materials such as dust, dirt, smoke, and smog.

•Sealed to protect against water, humidity and be non-condensing.

Beam Clearance

•Keep the scan engine’s beam sweep free from obstructions. For detailed

information on the exit beam angle and location please refer to Exit Beam

Specifications on page 4.

•A dark matte-finish on the internal walls of the housing can be utilized to

avoid internal beam reflections.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Lector de código de barras de Metrologic

Metrologic

Metrologic MS1633 FocusBT Manual de usuario

Metrologic

Metrologic Eclipse MS5145 Manual de usuario

Metrologic

Metrologic MS9520 Voyager Manual de usuario

Metrologic

Metrologic Stratos MS2xxx Series Instrucciones de instalación y funcionamiento

Metrologic

Metrologic 1070 Manual de usuario

Metrologic

Metrologic Genesis MS7580 Manual del propietario

Metrologic

Metrologic MS1890 Focus Manual de usuario

Metrologic

Metrologic MS2020 Stratos Manual de usuario

Metrologic

Metrologic Stratos MS2422 Manual de usuario

Metrologic

Metrologic MS6720 Manual de usuario

Metrologic

Metrologic MLPN 2159 Manual de usuario

Metrologic

Metrologic MS7620 Manual de usuario

Metrologic

Metrologic MS5100 Eclipse Series Manual de usuario

Metrologic

Metrologic MS7600 Manual de usuario

Metrologic

Metrologic MS5100 Eclipse Series Manual de usuario

Metrologic

Metrologic Cubit MS6520 Series Manual de usuario

Metrologic

Metrologic TwinScan IS220 Manual de usuario

Metrologic

Metrologic IS1000 Series Manual de usuario

Metrologic

Metrologic IS4225 ScanGlove Manual de usuario

Metrologic

Metrologic ScanQuest IS4110 Manual de usuario

Metrologic

Metrologic MS700i Manual de usuario

Metrologic

Metrologic MK5145-31A38 Manual de usuario

Metrologic

Metrologic MS7600 Manual de usuario

Metrologic

Metrologic 160 Guía del usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario