Metra Electronics 99-7011 Manual de usuario
INSTALLATION INSTRUCTIONS FOR PART 99-7011
99-7011
MITSUBISHI Lancer
2008-2010
KIT FEATURES
•DIN Radio Provision with Pocket
•ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
•Stacked ISO Mount Units Provision
•Painted to Match Factory
•A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) Double DIN Brackets
•E) Double DIN Trim Plate • F) Snap in Pocket
KIT COMPONENTS
A
Phillips Screwdriver/ Panel Removal Tool
•Cutting Tool
1-800-221-0932 www.metraonline.com
B
DE
C
F
TOOLS REQUIRED:
APPLICATIONS
©COPYRIGHT 2008-2009 METRA ELECTRONICS CORPORATION
WIRING AND ANTENNA CONNECTIONS: (Sold Separately)
Harness:
•MITO-02 - Mitsubishi amp interface harness 2007-up
• 70-7005 - Mitsubishi harness 2007-up
Antenna Adapter:
•No antenna adapter required
Dash Disassembly
-
Mitsubishi Lancer 2008-2010 . . . . . . . . . . . . . . . . . . .
. .
.
. . 1,2
Kit Preparation ............................................3
Kit Assembly
-DIN Radio Provision with Pocket .............................4
-ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 5
-Double DIN Radio Provision/Stacked ISO Mount Units Provision . . . . . . 6
Final Assembly ...........................................7
TABLE OF CONTENTS
99-7011
Note:
Refer also to the instructions included with the aftermarket radio.
K
NOWLEDGE IS
P
OWER
Enhanceyour installation and fabrication skillsby
enrolling in the most recognizedandrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.comor call
800-354-6782 for more informationandtake
steps towardabetter tomorrow.
1
3
MITSUBISHI LANCER 2008-2010
99-7011 DASH DISASSEMBLY
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Open the glove box and remove (1)
Phillips screw from the panel to the
right of the glove box door. Unclip
and remove the panel.
(Figure A)
Remove (1) Phillips screw from the
panel above the glove box then
unclip and remove the panel.
(Figure B)
Continued on page 2.
2
B
A
2
MITSUBISHI LANCER 2008-2010
99-7011 DASH DISASSEMBLY
4
Unclip the radio switch panel includ-
ing the hazard switch assembly.
Unplug hazard switch assembly and
remove panel.
(Figure C)
5
Remove (4) Phillips screws secur-
ing the radio chassis. Unplug and
remove chassis.
7
Unclip assembly, unplug ribbon
cable from assembly and remove
assembly from the factory radio
panel. Retain screws and hazard
switchassembly for re-use during
kit preparation.
6
Remove (3) Phillips screws securing
the hazard switch assembly to the
factory radio switch panel. Unclip
and remove the switch.
(Figure D)
8
Unclip and remove the a/c vents
from the factory radio switch panel.
(Retain a/c vents for re-use during
kit preparation)
9
Remove and retain (7) factory clips
from rear of radio housing for
re-use during kit preparation.
Continue to kit preparation.
PASSENGER
AIRBAGOFF
PASSENGER
PASSENGER
AIRBAG OFF
PASSENGER
D
C
3
99-7011 KIT PREPARATION
Secure the hazard switch assembly into the radio housing using the factory hard-
ware. Snap the a/c vents into the radio housing.
(Figure A)
Use the (7) plastic factory clips previously removed during dash disassembly and
attach where shown.
(Figure B)
1
2
PASSENGER
PASSENGER
AIRBAG OFF
A
REAR VIEW OF RADIO HOUSING
B
MITSUBISHI LANCER 2008-2010
Continue to kit assembly
99-7011 KIT ASSEMBLY
4
A
B
C
DIN RADIO PROVISION WITH POCKET
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward.
(Figure A)
1
Slide the aftermarket radio into the
cage until it snaps into place.
(Figure B)
2
Snap the pocket into the radio hous-
ing.
(Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
99-7011 KIT ASSEMBLY
5
A
B
C
ISO MOUNT RADIO PROVISION WITH POCKET
Mount the ISO Brackets to the radio
using the screws supplied with the
radio.
(Figure A)
1
Slide the radio into the radio housing
until it snaps into place.
(Figure B)
2
Snap the trim plate onto the front of
the radio housing.
(Figure B)
3
Snap the Pocket into the radio housing.
(Figure C)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
99-7011 KIT ASSEMBLY
6
DOUBLE DIN RADIO PROVISION
STACKED ISO MOUNT UNITS PROVISION
Cut and remove the center bar from
the radio housing.
(Figure A)
1
Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure B)
2
Slide the Double DIN or stacked ISO
mount unit(s) into the bracket/radio
housing assembly and securethe
unit(s) to the assembly using the
screws supplied with the unit(s).
(Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
B
C
Snap the Double DIN trim plate onto
the front of the radio housing.
(Figure C)
4
99-7011 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground..................Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
7
99-7011
NOTES
8
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Metra Electronics
Metra Electronics
Metra Electronics 95-3302 Manual de usuario
Metra Electronics
Metra Electronics 99-3100 Manual de usuario
Metra Electronics
Metra Electronics 95-8210 Manual de usuario
Metra Electronics
Metra Electronics 99-8222 Manual de usuario
Metra Electronics
Metra Electronics 99-6510 Manual de usuario
Metra Electronics
Metra Electronics 99-8715 Manual de usuario
Metra Electronics
Metra Electronics 99-9224 Manual de usuario
Metra Electronics
Metra Electronics 99-2005 Manual de usuario
Metra Electronics
Metra Electronics 99-9000 Manual de usuario
Metra Electronics
Metra Electronics 99-3012G-LC Manual de usuario
Metra Electronics
Metra Electronics 70-1787 Manual de usuario
Metra Electronics
Metra Electronics 99-6520B Manual de usuario
Metra Electronics
Metra Electronics 71-1729 Manual de instrucciones
Metra Electronics
Metra Electronics GMLAN29-100 Manual de usuario
Metra Electronics
Metra Electronics 99-7893 Manual de usuario
Metra Electronics
Metra Electronics 99-3309B Manual de usuario
Metra Electronics
Metra Electronics 99-7316 Manual de usuario
Metra Electronics
Metra Electronics 95-6534B Manual de usuario
Metra Electronics
Metra Electronics 99-3009 Manual de usuario
Metra Electronics
Metra Electronics 95-8166G Manual de usuario
