M-system R5T-RS Manual de usuario

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

RTD input module...............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■HOT INSERTION/REMOVAL OF MODULES

• Removing or replacing modules does not affect other mod-

ules on the same backplane. It is possible to replace them

without removing the power supply. However, replacing

multiple modules at once may greatly change line voltage

levels. We recommend that you replace them one by one.

■GENERAL PRECAUTIONS

• DO NOT set the switches while the power is supplied.

The switches are used only for maintenance without the

power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continu-

ous vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

INSTALLATION

Use the Installation Base (model: R5-BS).

RTD INPUT MODULE

(screw terminal block) MODEL R5T-RS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-6115 Rev.3 P. 1 / 3

INSTRUCTION MANUAL

COMPONENT IDENTIFICATION

RUN

RUN LED

12345678

RTD Burnout

Temp. Unit

Function

■ SIDE VIEW ■FRONT VIEW

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

■SIDE DIP SW

(*) Factory setting

• RTD Type: SW1, 2, 3, 4

SW RTD

1234

ON OFF ON OFF Cu 10 @ 25°C

OFF OFF OFF OFF Cu 50

OFF OFF OFF ON JPt 100 (JIS ’89)

ON OFF OFF OFF Pt 100 (JIS ’89)

OFF ON OFF OFF Pt 100 (JIS ’97, IEC) (*)

OFF ON ON OFF Pt 1000

ON ON OFF OFF Pt 50 Ω (JIS ’81)

OFF OFF ON OFF Ni 100

ON ON ON OFF Ni 508.4 Ω

• Temperature Unit: SW5, 6

SW TEMP. UNIT

5 6

OFF OFF °C (*)

ON OFF °F

OFF ON K (Absolute Temp)

• Burnout: SW7, 8

BURNOUT7 8

INPUT 1 INPUT 2

OFF OFF Downscale

ON ON Upscale (*)

PC CONFIGURATOR

With conﬁgurator software, settings shown below are available.

Refer to the software manual of R5CON for detailed operation.

■CHANNEL INDIVIDUAL SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Zero Scale -32000 to +32000 0

Full Scale -32000 to +32000 10000

Bias [Zero Adj.] -320.00 to +320.00 0.00

Gain [Span Adj.] -32000 to +32000 1.0000

Zero Base Depends on sensor type 0.00

Full Base Depends on sensor type 0.00

■CHANNEL BATCH SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Limit No check mark: Limits to the scaling values equivalent to -15 % to

+115 %.

Check-marked: Limits within Zero Scale to Full Scale.

No check mark

R5T-RS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-6115 Rev.3 P. 2 / 3

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

38.5 (1.52) 98.5 (3.88)

TERMINAL COVER

6–M3.5

TERMINAL

SCREWS

8.2 (.32)

7.2 (.28)

LOCKING CLAMP

90 (3.54) 5.6

(.22)

18 (.71)

POSITIONING GUIDE

■CONNECTION DIAGRAM

BUS CONNECTOR

INTERNAL

POWER

INTERNAL BUS A

INTERNAL BUS B*

*For dual redundant communication.

Note: The section enclosed by broken line is with 2-ch. option.

INPUT 1

RTD

INPUT 2

RTD

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.8 N·m

R5T-RS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-6115 Rev.3 P. 3 / 3

Otros manuales de Sistema de E/S de M-system

M-system

M-system R3-PC16A Manual de usuario

M-system

M-system R7F4DC-DA16A-J Manual de usuario

M-system

M-system R30XN16A Manual de usuario

M-system

M-system R7ML-LC2 Manual de usuario

M-system

M-system R30NE1 Manual de usuario

M-system

M-system R7 Series Manual de usuario

M-system

M-system R30SV2 Manual de usuario

M-system

M-system 6BSN Manual de usuario

M-system

M-system R3-SV8N Manual de usuario

M-system

M-system Devicenet R7F4HD-DC32A Manual de usuario

M-system

M-system R7 Series Manual de usuario

M-system

M-system R7ML-YS2-R Manual de usuario

M-system

M-system R5T-PA2 Manual de usuario

M-system

M-system R7F4HC-DA32-K Manual de usuario

M-system

M-system R8-CT4E Manual de usuario

M-system

M-system R10M-CT4E Manual de usuario

M-system

M-system R3-DA64A Manual de usuario

M-system

M-system R3-RS8B Manual de usuario

M-system

M-system R7 Series Manual de usuario

M-system

M-system R7M-CT4E-R Manual de usuario

M-system

M-system R3-SV16N Manual de usuario

M-system

M-system R3-TS8 Manual de usuario

M-system

M-system R7ML-DC16A-R Manual de usuario

M-system

M-system R8-SS4N Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario

WAGO

WAGO I/O-SYSTEM 750 Manual de usuario