LSL K12R Guía de instalación

Fitting Instruction

Article-No. : 120B029

Product : Super Bike Conversion Kit

Model : BMW BMW K1200R 2005 – 2008 / K1300R 2009

Type : K12R / K12S

Important:

Read this instruction manual carefully and mind all warnings and tips. You should do this work

only if you‘re qualified; otherwise we recommend this mounting to be done by a professional

workshop. Improperly mounting of this kit can reduce the driveability of the motorcycle and may be

a risk to your health and life.

Special works are marked with the following signs. Please take special care on these works.

Warning! Important mounting instruction. It shows risks to your life and health.

Tips for mounting and maintenance or to avoid damage.

Mounting:

To avert any damage from the electrical systems of your motorcycle, you should

disconnect the battery ground while installing the Superbike conversion kit.

Remove handlebar controls, clutch lever bracket and brake cylinder assy, then remove the

original handlebar.

Dismount the original top yoke and install the Superbike top yoke. To demount the ignition lock

you need to drill out the heads of the breakaway bolts. Use the attached bushings (length

12mm) in combination with the M8x25mm bolts as a steering stop. Use fluid bolt lock as

Loctite 243 or 270. Fit the ignition lock with the attached bushings (length 23,5mm), new bolts

(M8x45mm) and corrugated washers underneath the bolts heads at the LSL-yoke. You should

drill out the hexagon sockets of the bolts as theft protection. To fix top yoke, tighten steering

head up to the original torque that refers to the vehicle manufacturer’s instruction.

———————————————— Accessories from — The Original ——

Rev. 00 22/10/2010 Page 1 of 3

———————————————— Accessories from — The Original ——

Rev. 00 22/10/2010 Page 2 of 3

Required handlebar type: LSL Fat Bar flat, Type XN1

Mount new handlebar into the clamps. Evenly tighten the handlebar clamps and tighten them

with 25Nm / 18.44lbf ft torque after the whole fitment is done.

Mount the handlebar controls and levers as shown and install the brake and clutch units

with approximately 25mm spacing to the controls, as shown.

Assure (without brake pressure) that the brake lever can be drawn up to the grip and

doesn’t contact the handlebar controls before. (Loosening one calliper and wobble it on

the disk to push the pistons back should be the easiest way.)

Check clearance between fuel tank and handlebar as well as to the fairing; readjust handlebar

and controls if necessary.

K1200R: To fit the left grip, drill two holes (3.5mm) and fix the grip with the original cutting

screws.

K1300R: To fit the left grip, drill an end-to-end hole (4.0mm) and fix the grip with the original

bolt.

! !

Installation notes for wires, cables and hoses:

Throttle cable: Route the throttle cable, as

shown, on the shortest way to the tank

cover. Check throttle cable for free

movement on every steering angle.



Brake and Clutch hoses: Route them as shown in the picture. Lay clutch hose above the

fairing support and fix it with a cable tie (see in the picture above). Fix throttle cables and

clutch hose with a cable tie so they won’t touch the steering damper!

———————————————— Accessories from — The Original ——

Rev. 00 22/10/2010 Page 3 of 3

Handlebar Control harnesses: Unwrap the harnesses at the branching points and shorten

the down leading tubes by 2cm. Spread the wires and seal the new branching points with

insulating tape.

Make sure that no cable, hose or harness is bended and stays tension-free over the

whole steering angle.

The Superbike Conversion kit is now installed correctly.

We, the team of LSL Motorradtechnik Germany, wish you enjoyable driving!

LSL-Motorradtechnik GmbH • D-47809 Krefeld

www.lsl.eu

Otros manuales para K12R

1

Este manual sirve para los siguientes modelos

2

Tabla de contenidos

Otros manuales de Accesorios para motocicletas de LSL

LSL

LSL 556KT07 Series Guía de instalación

LSL

LSL 120B040ABS Guía de instalación

LSL

LSL 377-610SW Manual de usuario

LSL

LSL 377-530SW Manual de usuario

LSL

LSL ZGT40A Guía de instalación

LSL

LSL 460Y129 Manual de usuario

LSL

LSL 555K131 Series Guía de instalación

LSL

LSL 150H131 Guía de instalación

LSL

LSL CLASSIC 555T109-Gv Manual técnico

LSL

LSL SC59 Guía de instalación

LSL

LSL 153T071R Guía de instalación

LSL

LSL 377-805SW Manual de usuario

LSL

LSL 153K136R Guía de instalación

LSL

LSL 153Y139S Guía de instalación

LSL

LSL 150T064 Guía de instalación

LSL

LSL MANTIS-RS Manual técnico

LSL

LSL 153T072R Guía de instalación

LSL

LSL 377-590SW Manual de usuario

LSL

LSL 153T072H Guía de instalación

LSL

LSL PC19 Guía de instalación

LSL

LSL 377-500SW Manual de usuario

LSL

LSL 150KT09 Manual de usuario

LSL

LSL 377-855SW Manual de usuario

LSL

LSL 110B058 Guía de instalación

Manuales populares de Accesorios para motocicletas de otras marcas

SRC

SRC B-TRK502-01-01-SL Manual de usuario

3M

3M Speedglas 9100 MP Manual de usuario

hepco & becker

hepco & becker 6307520 00 01 Manual de usuario

HOMCOM

HOMCOM AA0-077 Manual de usuario

hepco & becker

hepco & becker 6307558 00 01 Manual de usuario

Wunderkind Custom

Wunderkind Custom 106503-F15 Guía del usuario

Dräger

Dräger HPS 3500 Manual de usuario

M-WAVE

M-WAVE SKI Manual de usuario

Kuryakyn

Kuryakyn 6212 Manual de usuario

hepco & becker

hepco & becker 6507504 00 01 Manual de usuario

Tool it

Tool it PROMAX LCD 9.13G Manual de usuario

Custom Dynamics

Custom Dynamics TruWrapz Manual de usuario

Roof

Roof RO200 CARBON Manual de usuario

Kabuto

Kabuto Japan IBUKI Manual de usuario

PUIG

PUIG 5051 Manual de usuario

rizoma

rizoma ZTH050 Manual de usuario

Joubert

Joubert 10001711 Manual de usuario

Sperian

Sperian Optrel p420 Manual de usuario