LSL ZGT40A Guía de instalación

Fitting Instruction

Article-No. : 120K130

Product : Super Bike Conversion Kit

Model : Kawasaki GTR 1400 2008Æ

Type : ZGT40A

Important:

Read this instruction manual carefully and mind all warnings and tips. You should do this work

only if you‘re qualified; otherwise we recommend this mounting to be done by a professional

workshop. Improperly mounting of this kit can reduce the driveability of the motorcycle and may

be a risk to your health and life.

Special works are marked with the following signs. Please take special care on these works.

Warning! Important mounting instruction. It shows risks to your life and health.

LTips for mounting and maintenance or to avoid damage.

Fitting:

Mounted conversion kit

LThe battery ground should be disconnected before working on electric wiring and switches!

———————————————— Accessories from — The Original ——

Rev. 00 08/04/2009 Page 1 of 4

Remove brake-hose(s). Caution: avoid brake fluid on painted surfaces! Any work on the

brake system or bleeding the system should be done by an authorized dealer or a

d mechanic!qualifie

Remove handlebar controls, clutch lever bracket and brake cylinder assy, then remove the

original handlebar. Loosen the clutch hose’s fixation at the top yoke

Mounting the adapter is done in

several steps:

1. Mount clamping devices (A)

loosely on the adapter plate

(B). Fit handle bar into the

clamping devices (A) and

tighten them with nickel-

plated M8x25 slightly so the

clamps can align to the

handle bar. Now tighten the

bolts from underneath the

plate with 25Nm / 18.44lbf ft

torque. Demount handle bar

at last.

2. Fix adapter brackets (C) on

the top yoke with M8x30 and

tighten them with 25Nm /

18.44lbf ft torque.

3. Fit pre-mounted adapter

(A&B) with nickel-plated

M8x25 and M8x45 on the

adapter brackets (C). Tighten

them with 25Nm / 18.44lbf ft

torque also.

LRecommended handlebar type: LSL-Fat Bar, high / Type XB3

Mount new handle bar into the clamps and adjust it. If the upper clamp is marked, the mark faces

forward. Tighten the handlebar clamps evenly with 25Nm / 18.44lbf ft torque.

Remount all handle bar controls and adjust them. Remember to check clearance between fairing

and handlebar and re-adjust handle bar, if necessary. Now you can drill bores to fix the handlebar

controls, if using a LSL-handlebar. Mount the left grip with suitable glue.

LIt was necessary to reduce the glove boxes opening angle to reach an ergonomic seating.

Take care to avoid damage to the glove boxes cover.

———————————————— Accessories from — The Original ——

Rev. 00 08/04/2009 Page 2 of 4

Instructions for rerouting cables hoses and wiring harness:

Throttle cable: Routed as original. Check throttle cable for free movement on every steering

angle.

Brake hose: Mount attached brake hose

with new seal rings. Mind the mounting

instructions that are delivered with the brake

hose. Route as shown and fix it with

rubberized clamp and zinc-plated bolt

M6x12 at the bracket.

Clutch hose: The laying needs no change, but the

fixation at the top yoke needs to be moved upward. Fit

new bracket with nickel-plated bolt M6x12 on the top

yoke; then fix clutch hose with original bolt, attached

washer and self-locking nut M6 at the bracket.

Wiring harness: No changes, routed as original.

Make sure that no cable, hose or harness is

bended and stays tension-free over the whole

steering angle.

The conversion kit is now completely mounted. Always check local laws and your manufacturer’s

warranty conditions for using aftermarket parts on your bike!

Ride safe and have fun!

———————————————— Accessories from — The Original ——

Rev. 00 08/04/2009 Page 3 of 4

LSL-Motorradtechnik GmbH • D-47809 Krefeld

www.lsl.eu

———————————————— Accessories from — The Original ——

Rev. 00 08/04/2009 Page 4 of 4

Tabla de contenidos

Otros manuales de Accesorios para motocicletas de LSL

LSL

LSL Superbike-Kit Guía de instalación

LSL

LSL 506Y017A Guía de instalación

LSL

LSL 377-850SW Manual de usuario

LSL

LSL 377-810SW Manual de usuario

LSL

LSL SC59 Guía de instalación

LSL

LSL 120H125 Guía de instalación

LSL

LSL 110K155SW Guía de instalación

LSL

LSL 377-805SW Manual de usuario

LSL

LSL 120B028 Guía de instalación

LSL

LSL 377-550SW Manual de usuario

LSL

LSL 153K136R Guía de instalación

LSL

LSL 506Y141A Guía de instalación

LSL

LSL 377-705SW Manual de usuario

LSL

LSL Superbike-Kit Guía de instalación

LSL

LSL 460T031 Guía de instalación

LSL

LSL 377-525SW Manual de usuario

LSL

LSL 377-855SW Manual de usuario

LSL

LSL 153Y137R Guía de instalación

LSL

LSL 377-505SW Manual de usuario

LSL

LSL CLASSIC 555T109-Gv Manual técnico

LSL

LSL 377-700SW Manual de usuario

LSL

LSL 120K084 Guía de instalación

LSL

LSL 153Y094H Guía de instalación

LSL

LSL Crash Pad 1290 Manual de usuario

Manuales populares de Accesorios para motocicletas de otras marcas

SRC

SRC B-TRK502-01-01-SL Manual de usuario

3M Speedglas 9100 MP Manual de usuario

hepco & becker

hepco & becker 6307520 00 01 Manual de usuario

HOMCOM

HOMCOM AA0-077 Manual de usuario

hepco & becker

hepco & becker 6307558 00 01 Manual de usuario

Wunderkind Custom

Wunderkind Custom 106503-F15 Guía del usuario

Dräger

Dräger HPS 3500 Manual de usuario

M-WAVE

M-WAVE SKI Manual de usuario

Kuryakyn

Kuryakyn 6212 Manual de usuario

hepco & becker

hepco & becker 6507504 00 01 Manual de usuario

Tool it

Tool it PROMAX LCD 9.13G Manual de usuario

Custom Dynamics

Custom Dynamics TruWrapz Manual de usuario

Roof

Roof RO200 CARBON Manual de usuario

Kabuto

Kabuto Japan IBUKI Manual de usuario

PUIG

PUIG 5051 Manual de usuario

rizoma

rizoma ZTH050 Manual de usuario

Joubert

Joubert 10001711 Manual de usuario

Sperian

Sperian Optrel p420 Manual de usuario