Lippert Components Edge Manual de usuario

Edge™ Awning

OEM INSTALLATION MANUAL

Rev: 10.24.19 Page 2 CCD-0002685

TABLE OF CONTENTS

Introduction 2

Safety 2

Prior to Installation 3

Resources Required 3

Installation 3

Awning Rail Installation (If Needed) 3

Awning Installation 4

Securing the Fabric 6

Solera Serenity LED Lights Installation - Optional 7

Seal Wall Penetrations 7

Awning Wiring 8

Wiring Diagram 9

Introduction

The Edge™ Awning features an internal motor to steadily operate the awning. The awning can come

equipped with optional Serenity LED lights.

Safety

The manual provides general instructions. Many variables can change the circumstances of the instructions,

i.e., the degree of difficulty, operation and ability of the individual performing the instructions. This

manual cannot begin to plot out instructions for every possibility, but provides the general instructions,

as necessary, for effectively interfacing with the device, product or system. Failure to correctly follow the

provided instructions may result in death, serious personal injury, severe product and/or property damage.

The "WARNING" symbol above is a sign that a procedure has a safety risk involved and may cause death

or serious personal injury if not performed safely and within the parameters set forth in this manual.

Failure to follow instructions provided in this manual may result in death, serious personal injury

and/or severe product and property damage, including voiding of the component warranty.

Unit MUST be supported per manufacturer's recommendations before working underneath. Failure

to do so may result in death or serious personal injury.

Always wear eye protection when performing service, maintenance or installation procedures.

Other safety equipment to consider would be hearing protection, gloves and possibly a full face

shield, depending on the nature of the task.

Moving parts can pinch, crush or cut. Keep clear and use caution.

The "CAUTION" symbol above is a sign that a procedure has a safety risk involved and may cause personal

injury, product or property damage if not performed safely and within parameters set forth in this manual.

Rev: 10.24.19 Page 3 CCD-0002685

Prior to Installation

All screws supporting the awning assembly must have a backer within the structure of the wall of the unit.

Refer to the unit's manufacturer for proper location of backer material.

Resources Required

Installation

Awning Rail Installation (If Needed)

NOTE: Awning rail not included.

1. Position the awning rail along the line where the roof and wall meet or:

A. For pitched awnings, a minimum of 6” above doors or windows

B. For flat awnings, a minimum of 4” above doors or windows

NOTE: The awning rail MUST be level and parallel with the floor line of the unit (Fig. 1).

Fig. 1

2. After determining the awning rail's proper location, mark its position with a non-permanent method of marking.

3. Seal the back of the awning rail with silicone sealant or tape.

4. Align the awning rail on the wall and secure with #10 x ¾” screws, using all fastener holes.

Roll Tube Assembly

Floor Line

Awning

Rail

Support Arm

Assembly

Support Arm

Assembly

• 2 -3 People, depending on task

• Cordless or electric drill or screw gun

• Appropriate drive bits

• Rivet gun (if needed)

• Screwdriver

• #6 x ½" hex head screws

• #10 x ¾" screws

• #14 x 1 ¼" screws

• Wire cutters/strippers

• Non-permanent method of marking

• Silicone sealant or tape

• Silicone lubricant

Rev: 10.24.19 Page 4 CCD-0002685

Fig. 2

Awning Width is from

Centerline to Centerline of

Support Arm Assemblies

Awning

Rail

Floor Line

Awning Installation

1. On the awning rail, mark the position of the centerlines of the support arm assemblies. Make sure that

the support arm assemblies will not interfere with any lights, vents or other obstructions.

2. Using a non-permanent method of marking, mark a perpendicular line from the awning rail down to

the floor line. This is the centerline of the support arm assembly (Fig. 2).

Fig. 3

3. Insert the drive head assembly shaft into the end cap (Fig. 3).

A. Align the holes and secure with waxed screw.

B. Repeat process for idler head assembly at opposite end of roll tube.

NOTE: Keep the head of the wax screw ⁄" from being fully fastened to avoid compromising the structural

integrity of the wax screw.

Drive Head

Assembly Shaft

Support Arm

Centerline

End Cap

Rev: 10.24.19 Page 5 CCD-0002685

Fig. 4

4. Use a screwdriver to spread open either end of the awning rail channel (Fig. 4A).

5. To protect the fabric from damage during installation, file any sharp edges or burrs from the awning

rail channel (Fig. 4B).

6. Use silicone lubricant and spray the inside of the awning rail channel (Fig. 4B).

9. Lift the support arm assembly up against the bottom of the awning rail and attach it to the side of the

unit with two #14 x 1 1/4" screws at the top (Fig. 5A) and one screw at the bottom (Fig. 6A).

NOTE: Make sure the awning assembly is square on the unit prior to mounting the bottom screw.

NOTE: Three rivets with ⁄" grip range can be used in place of the two middle and one lower screws for

laminated walls.

10. Repeat step 9 for the other side.

7. Remove the tape from the fabric. Unroll a small portion of fabric.

NOTE: The next steps will require three people: One to feed the polycord into the awning rail channel; two

to walk the support arm assemblies along the awning rail while the fabric slides into position.

8. Slide the polycord into the awning rail channel and walk the support arm assemblies and fabric down

the awning rail channel until the support arm assemblies are in line with the centerline marks.

Failure to mount the support arm assembly tight to the underside of the awning rail will result in failure of

the awning to close properly.

Fig. 5

Fig. 6

Rev: 10.24.19 Page 6 CCD-0002685

Fig. 7

Securing the Fabric

1. Extend and retract the awning several times to make sure the fabric is square on the roll tube.

2. Secure the fabric in the awning rail no more than 1” inside the edge of the fabric on both ends using

a #6 x ½” hex head screw. Install the screw down through the awning rail into the fabric and the

polycord (Fig. 8).

Awning Rail Awning Rail

Polycord

Outer Edge

of Fabric

Idler Side

Outer Edge

of Fabric

Drive Side

Polycord

Hex Screw

Fig. 8

11. Cut the zip ties and connect the wires from the drive head assembly to a drill battery and run the

awning half way out.

C. Install the remaining two #14 x 1 ¼” screws in the two screw slots in the center portion of the

awning assembly (Fig. 7A). Repeat for the other side.

Rev: 10.24.19 Page 7 CCD-0002685

Solera Serenity LED Lights Installation - Optional

The Solera Serenity LED Lights (Fig. 9A) come pre-installed on specifically-fitted support arms. Installation

also requires the proper fabric with an LED wire welded into the fabric at the base. The Edge Awning with

Serenity must be installed prior to wiring the Solera Serenity LED lights.

Fig. 10

1. Wire the LED wires on the idler arm to the wire welded into the awning fabric.

2. Connect the other end of the wire welded into the fabric to the drive arm Serenity LED wire and

connect both to the power source.

3. A 3 amp fuse that meets or exceeds RVIA standards MUST be installed in-line to protect the Serenity

LED lights wiring.

4. Connect the LED power wire to the unit's power source. Make sure the black wire is connected to a

ground and the red wire is connected to a positive 12V DC power source.

Seal Wall Penetrations

1. Seal all fastener locations and wire penetrations with silicone sealant to protect against water intrusion (Fig. 10).

Fig. 9

Rev: 10.24.19 Page 8 CCD-0002685

Awning Wiring

The Edge Awning motors come stock with an internal 6A auto-reset breaker. If this breaker trips, it will

take approximately 30 seconds to reset. LCI recommends the awning be wired with a 15A auto-reset

circuit protector. If the circuit protector trips, it will take approximately 30 seconds to reset. All wire shall

be 14 AWG or higher as necessary to provide 11.5V minimum at all times to the LCI-supplied power cable

connection.

1. Pull the wires from the unit through the support arm assembly. These wires may be located at the

bottom or the top of the support arm assembly.

2. Connect wiring from the unit to the switch and the awning drive head. See Wiring Diagram (Fig. 11).

3. Check the switch. If the awning is running in reverse of what the switch indicates, reverse the wires.

Rev: 10.24.19 Page 9 CCD-0002685

15A Auto-Reset

Circuit Protector

per RVIA Code

(OEM Supplied)

Red

Black

Manual

Rocker

Switch*

Blue

Red

Awning Motor

12V DC Battery,

Power Source

or Converter

White

Ground

Power

1 4

**Jumper wires are internal

+ 

Wiring Diagram

*Wire colors may vary depending on what switch is used.

Wire colors shown reference using a LCI Rocker Switch.

End View of Wiring Harness

Red **Jumper wire

1 to 6

Black **Jumper wire 4

to 3

White 2

Blue 5

Fig. 11

The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. (“LCI”).

LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an

authorized LCI representative has been provided. Any unauthorized use shall void any applicable warranty.

The information contained in this manual is subject to change without notice and at the sole discretion of LCI.

Revised editions are available for free download from lci1.com.

Please recycle all obsolete materials.

For all concerns or questions, please contact

Lippert Components, Inc.

Ph: (574) 537-8900 | Web: lci1.com | Email: [email protected]

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Lippert Components

Lippert Components

Lippert Components Solera Instrucciones de instalación

Lippert Components

Lippert Components Kwikee Manual de usuario

Lippert Components

Lippert Components SOLERA SLIDER Manual de usuario

Lippert Components

Lippert Components In-Wall Slide-Out Manual de usuario

Lippert Components

Lippert Components Sway Command Manual

Lippert Components

Lippert Components Solera Classic Instrucciones de instalación

Lippert Components

Lippert Components Vela Manual de usuario

Lippert Components

Lippert Components Solera Slide Topper Manual de usuario

Lippert Components

Lippert Components ABOVE FLOOR SLIDEOUT SYSTEM Manual de usuario

Lippert Components

Lippert Components X-Trek Manual de usuario

Lippert Components

Lippert Components SolidStep Instrucciones de instalación

Lippert Components

Lippert Components SolidStep 3.0 Premium Step Manual de usuario

Lippert Components

Lippert Components Tire Linc Manual de usuario

Lippert Components

Lippert Components Curt Rota-Flex Pin Box Manual de usuario

Lippert Components

Lippert Components Solera Power Awning Manual de uso y cuidado

Lippert Components

Lippert Components Ground Control 2.0 Manual de usuario

Lippert Components

Lippert Components Happijac Manual de usuario

Lippert Components

Lippert Components A-Frame Coupler Instrucciones de instalación

Lippert Components

Lippert Components Ground Control 3.0 Landing Gear Manual de usuario

Lippert Components

Lippert Components Air Ride 155925 Instrucciones de instalación

Lippert Components

Lippert Components Solera Power Awning Manual de uso y cuidado

Lippert Components

Lippert Components Solera Manual de usuario

Lippert Components

Lippert Components SolidStep XF Manual de usuario

Lippert Components

Lippert Components SURESHADE POWER BIMINI Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario