Lippert Components Jack-It Manual de usuario

Jack-It

Aftermarket Manual

www.lippertcomponents.com (574) 537-8900 Rev: 06.16 - Jack-It Aftermarket Manual

Introduction

The Jack-IT® is a bicycle rack designed to attach to your RV.

Additional information about this product can be obtained from

www.lci1.com/support or by downloading the free myLCI app.

The app is available on iTunes® for iPhone® and iPad® and

also on Google Play™ for Android™ users.

iTunes®, iPhone®, and iPad® are registered trademarks of

Apple Inc. Google Play™ and Android™ are trademarks of

Google Inc

Lippert Components, Inc. recommends that the following

inspections, troubleshooting, component replacement, and

verications be completed only by certied RV technicians.

Safety Requirements

Moving parts can pinch,

crush or cut. Keep clear

and use caution.

Failure to follow the

instructions provided in

this manual may result

in death, serious injury,

vehicle damage, or

voiding of the component

warranty.

Jack-It

Aftermarket

Manual

Table Of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Tools required 2

Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 2

Securing Bikes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Patent protected, trademarked, and produced by Let’s Go Aero, Inc

Corporate Ofce: 4474 Barnes Road, Colorado Springs, CO 80917 USA.

Made in China.

US Patent Numbers: 8,899,456, D717,716, D717,717, D684,917, D722,289,

patents pending.

Jack-It

Aftermarket Manual

www.lippertcomponents.com (574) 537-8900 Rev: 06.16 - Jack-It Aftermarket Manual

Preparation

Tools required

9/16” Socket Wrench

3/4” Socket Wrench

Installation Instructions

1. Remove the tongue jack from the coupler. Position the

PowerTower ™ (Fig. 1G) on the coupler. Place the jack on

the PowerTower™ (Fig. 1G) and secure both to the coupler

using 3 nuts, bolts and washers each (Fig. 1H, 1I, 1J).

Note: If there is no tongue jack, attach the PowerTower™ (Fig.

1G) to the coupler on the front of the trailer using 3 nuts,

bolts and washers each (Fig. 1H, 1I, 1J).

2. Attach the stinger (Fig. 1F) to the PowerTower™ (Fig. 1G)

using NoMotion™ pin and washers (Fig. 1C, 1D, 1A). For

safety, insert cotter pin (Fig. 1B) through the hole at the end

of the NoMotion™ pin (Fig. 1C) after tightening securely.

3. Attach base (Fig. 1E) to stinger (Fig. 1F) using NoMotion™

pin and washers (Fig. 1C, 1D, 1A). For safety, insert cotter

pin (Fig.1B) through the hole at the end of the NoMotion™

pin (Fig. 1C) after tightening securely.

Fig.1

The use of this product

while bicycles are loaded

may affect the turning

radius on some vehicles.

Check the turning radius

before travel.

Jack-It

Aftermarket Manual

www.lippertcomponents.com (574) 537-8900 Rev: 06.16 - Jack-It Aftermarket Manual

Fig.2

C D E

Securing Bikes

1. For two bicycles, the best technique is to postion the bicycles

front to back / back to front with the chain ring to the outside.

2. Hang one bicycle on the tow vehicle side of the bicycle rack,

so the top of the wheels are each supported by a cradle.

3. Secure by tensioning each rubber strap over the top of each

tire and engaging a strap hole with the end of the cradle.

4. Use the SwayStop™ pin to secure one wheel below the

frame where the wheel crosses the wing using the same

technique with the rubber strap (Fig. 3).

5. Repeat for a second bicycle on the trailer side of the bicycle

rack.

Note: Several hole positions are provided

for cradles (Fig. 2A). Pads (Fig. 2D) and

SwayStop™ pins (Fig. 2F) slide along the

length of wings (Fig. 2G).

4. If not already in place, slide two pads (Fig. 2D)

onto each wing (Fig. 2G).

5. Slide one SwayStop™ pin (Fig. 2F) onto each

wing (Fig. 2G). Attach wings (Fig. 2G) to base

(Fig. 2E) using two snap pins (Fig. 2H).

Note: SwayStop™ pins (Fig. 2F) should point in

opposite directions.

6. Install six rubber straps (Fig. 2B) one onto each

cradle (Fig. 2A) and one onto each SwayStop™

pin (Fig. 2F).

7. Attach four cradles (Fig. 2A). Attach two to each

wing (Fig. 2G) securing with cotter pins (Fig.

2C). Attach one on each wing facing the tow

vehicle and one on each wing facing the trailer.

Note: Adjustment will be necessary depending on

the size and desired position of the bicycles.

Always make sure all connections between the bicycle rack and the trailer

coupler are secure / tight / ready for travel. Always make sure the bicycles

are securely attached to the bicycle rack before you drive away.

Fig.3

Jack-It

Aftermarket Manual

www.lippertcomponents.com (574) 537-8900 Rev: 06.16 - Jack-It Aftermarket Manual

Manual information may be distributed as a complete

document only, unless Lippert Components provides explicit

consent to distribute individual parts.

All manual information is subject to change without notice.

Revised editions will be available for free download at www.

lippertcomponents.com. Manual information is considered

factual until made obsolete by a revised version.

Please recycle all obsolete materials and contact Lippert

Components with concerns or questions.

Notes

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Lippert Components

Lippert Components

Lippert Components Solera Slide Topper Manual de usuario

Lippert Components

Lippert Components SolidStep XF Manual de usuario

Lippert Components

Lippert Components SolidStep 3.0 Premium Step Manual de usuario

Lippert Components

Lippert Components In-Wall Slide-Out Winnebago Instrucciones de funcionamiento

Lippert Components

Lippert Components Solera Manual de usuario

Lippert Components

Lippert Components Happijack FT-DR2 Manual de usuario

Lippert Components

Lippert Components Edge Manual de usuario

Lippert Components

Lippert Components Ground Control 3.0 Landing Gear Manual de usuario

Lippert Components

Lippert Components SolidStep XF Manual de usuario

Lippert Components

Lippert Components COACH STEP Guía de configuración

Lippert Components

Lippert Components ABOVE FLOOR SLIDEOUT SYSTEM Manual de usuario

Lippert Components

Lippert Components Kwikee Manual de usuario

Lippert Components

Lippert Components Curt Rota-Flex Pin Box Manual de usuario

Lippert Components

Lippert Components X-Trek Manual de usuario

Lippert Components

Lippert Components 432223 Manual de usuario

Lippert Components

Lippert Components ground control 3.0 Guía

Lippert Components

Lippert Components Levelegs Manual del propietario

Lippert Components

Lippert Components ground control TT Instrucciones de instalación

Lippert Components

Lippert Components Solera Instrucciones de instalación

Lippert Components

Lippert Components In-Wall Slide-Out Manual de usuario

Lippert Components

Lippert Components Alumi-Tread series Manual de usuario

Lippert Components

Lippert Components Innolight Sliding Instrucciones de instalación

Lippert Components

Lippert Components Tire Linc Manual de usuario

Lippert Components

Lippert Components Sliding Swivel Seat Base Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario