LevelOne WAP-0005 Manual de usuario

9570N900A0

LevelOne

WAP -0005

802.11g/802.11b PoE

Access Point

Quick Install Guide

Page 1

1. Introduction

Package Contents

The following items should be included:

If any of the above items are damaged or missing, please

contact your dealer immediately.

Physical Details

Front Panel LEDs

Status On -Error condition.

Off -Normal operation.

Blinking -This LED blinks during start up, or

when the Firmware is being upgraded.

Power On -Normal operation.

Off -No power

LAN On -The LAN (Ethernet) port is active.

Off -No active connection on the LAN (Ethernet)

port.

Flashing -Data is being transmitted or received

via the corresponding LAN (Ethernet) port.

Wireless

LAN On -Idle.

Off -Error-Wireless connection is not available.

Flashing -Data is being transmitted or received

via the Wireless access point. Data includes

"network traffic" as well as user data.

Page 2

Rear Panel

Antenna One antenna (aerial) is supplied. Best results are

usually obtained with the antenna in a vertical

position.

Reset Button

This button has two (2) functions:

Reboot. When pressed and released, the Wireless

Access Point will reboot (restart).

Reset to Factory Defaults. This button can also

be used to clear ALL data and restore ALL

settings to the factory default values, as follows:

1. Power Off the Access Point.

2. Hold the Reset Button down while you

Power On the Access Point.

3. Continue holding the Reset Button until the

Status (Red) LED blinks TWICE.

4. Release the Reset Button.

The factory default configuration has now been

restored, and the Access Point is ready for use.

Ethernet Use a standard LAN cable (RJ45 connectors) to

connect this port to a 10BaseT or 100BaseT hub

on your LAN.

Power port Connect the supplied power adapter here.

Page 3

2. Installation

1. Select a suitable location for the installation of your

Wireless Access Point. To maximize reliability and

performance, follow these guidelines:

•Use an elevated location, such as wall mounted or on

the top of a cubicle.

•Place the Wireless Access Point near the center of

your wireless coverage area.

•If possible, ensure there are no thick walls or metal

shielding between the Wireless Access Point and

Wireless stations.

2. Use a standard LAN cable to connect the “Ethernet” port

on the Wireless Access Point to a 10/100BaseT hub on

your LAN.

3. Connect the supplied power adapter to the Wireless

Access Point and a convenient power outlet, and power up.

Page 4

Note:

To use PoE (Power over Ethernet), the WAP –0005 should be

connected as shown below, rather than using steps 2 and 3

above.

Please be noted that PoE Adapter is not included in package.

4. Check the LEDs:

•The Status LED should flash, then turn OFF.

•The Power, Wireless LAN, and LAN LEDs should

be ON.

3. Access Point Setup

A simple Windows setup utility is supplied on the CD-ROM.

This utility can be used to assign a suitable IP address to the

Wireless Access Point. Using this utility is recommended,

because it can locate the Wireless Access Point even if it has an

invalid IP address.

Utility Installation

1. Insert the supplied CD-ROM in your drive.

2. If the utility does not start automatically, run the SETUP

program in the root folder.

3. Follow the prompts to complete the installation.

Page 5

Main Screen

•Start the program by using the icon created by the setup

program.

•When run, the program searches the network for all active

Wireless Access Points, then lists them on screen, as

shown by the example below.

The default settings are:

IP Address Automatic (DHCP Client)

If no DHCP Server is detected, the IP

address is 192.168.0.228

SSID wireless

Wireless

Security Disabled

If you want to change the default setting, follow the steps

below:

1. Select the desired Wireless Access Point.

2. Click the Set IP Address button.

Page 6

3. If prompted, enter the user name and password. The

default values are admin for the User Name, and

password for the Password.

4. Ensure the IP address, Network Mask, and Gateway are

correct for your LAN. Save any changes.

5. Click the Web Management button to connect to the

selected Wireless Access Point using your Web Browser.

If prompted, enter the User Name and Password again.

6. The following screen should appear:

Please refer to the manual for the setting instruction.

Page 7

4. Client (PC) Configuration

WEP/WPA-PSK Mode

Each Wireless Station must have the same settings as the

Wireless Access Point.

Mode On each PC, the mode must be set to

Infrastructure.

SSID (ESSID) This must match the value used on the

Wireless Access Point.

The default value is wireless

Note! The SSID is case sensitive.

WEP

WPA-PSK If WEP or WPA-PSK is enabled on the

Wireless Access Point, each station must

use the same settings as the Wireless

Access Point.

802.1x Mode

Using 802.1x requires extensive configuration. See the user

manual for details.

Otros manuales para WAP-0005

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de LevelOne

LevelOne

LevelOne WAP-0003 Manual de usuario

LevelOne

LevelOne WAB-3001 Manual de usuario

LevelOne

LevelOne WAB-3003 Manual de usuario

LevelOne

LevelOne WAP-8123 Manual de usuario

LevelOne

LevelOne WAP-6117 Manual de usuario

LevelOne

LevelOne WAB-5010 Manual de usuario

LevelOne

LevelOne WAP-6017 Manual de usuario

LevelOne

LevelOne WBR-2400TX Manual de usuario

LevelOne

LevelOne WAB-5120 Manual de usuario

LevelOne

LevelOne WAP-8021 Manual de usuario

LevelOne

LevelOne WAP-0002 Manual de usuario

LevelOne

LevelOne WAP-6011 Manual de usuario

LevelOne

LevelOne WAB-5120 Manual de usuario

LevelOne

LevelOne WAP-6010 Manual de usuario

LevelOne

LevelOne WAP-6121 Manual de usuario

LevelOne

LevelOne EAP-300 Manual de usuario

LevelOne

LevelOne WAP-3101 Manual de usuario

LevelOne

LevelOne WAB-7400 Manual de usuario

LevelOne

LevelOne WAB-3003 Manual de usuario

LevelOne

LevelOne WAP-6102 Manual de usuario

LevelOne

LevelOne WAP-0005 Manual de usuario

LevelOne

LevelOne WAP-6101 Manual de usuario

LevelOne

LevelOne EAP-110 Manual de usuario

LevelOne

LevelOne WAP-0005 Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario