LevelOne WAB-5120 Manual de usuario

- 1 -

LevelOne

WAB-5120

300Mbps Wireless Outdoor PoE Access Point/Bridge

Quick Installation Guide

English Deutsch

- 2 -

Table of Content

English......................................................................................................................................................- 3 -

Deutsch .....................................................................................................................................................- 9 -

This guide covers only the most common situations. All detailed information is described in the user

manual.

- 3 -

English

Hardware Installation

1. Loosen the screw with a screwdriver.

Grab the cover and pull it back harder to take it out

2. Plug Cat.5/5e/6 cable into the RJ-45 LAN1 port. Do not use the RJ45 LAN2 port.

3. Power on the CPE by press the black PWR button beside the LAN 1 Ethernet port.

4. Attach and fasten the removable cover to the bottom of the unit with the screw

- 4 -

5. Plug the power cord into the DC port of the PoE injector

6. Plug the other side of the Cat.5/5e/6 cable into the PoE port of the PoE injector. The

installation is finished and looks like the following picture.

- 5 -

Conﬁguration

Check Your Network Settings to login web UI

You need to assign your PC a Static IP address so the WAB-5120 can communicate with your

PC during configuration.

Select “Control Panel” > “Network Connections”.

Right click the “LocalArea Connection” and choose “Properties”.

Select the TCP/IP protocol for your network card.

Click on the Properties button. You should then see the following screen.

Click on “Use the following IP address” and enter the following IP address and subnet mask.

IP address: 192.168.1.229 Subnet mask: 255.255.255.0

Click “OK”.

Open your Web browser (Internet Explorer is recommended).

Then enter: http://192.168.1.1

You will see WAB-5120 Login page as following picture

Use the following username and password to login the device.

User name: admin Password: admin

- 6 -

AP Mode

1. Choose Wireless > Basic Settings for the wireless basic settings.

Click Apply.

If security is required, open Wireless > Profile Setting and enter “VAP Profile 1 Settings” as

below. Choose Network Authentication to change the security settings. Click Apply.

- 7 -

CPE Mode

1. Choose Wireless > Basic Settings for the wireless basic settings.

In Wireless mode, choose “Wireless Client” to operate in Client mode.

Click Apply.

2. Click the “Site Survey” button beside Wireless Mode. It will scan all the available access

points within coverage. Select the one you prefer to connect to, and click Selected to

establish the connection. You can also click Scan to re-scan the available access points.

- 8 -

3. If the AP you connect to needs authentication or password, click Profile Settings in the left

column, fill out the corresponding items, and click Apply for data encryption.

Congratulations!

The AP – CPE connection is now successfully configured.

- 9 -

Deutsch

Installation der Hardware

1. Lösen Sie die Schrauben mit einen Schraubendreher. Entfernen Sie das Gehäuse mit einem

kräftigen Ruck.

2. Stecken Sie ein Cat.5/5e/6 Kabel in den RJ45 LAN1-Port. Verwenden Sie NICHT den RJ45

LAN2-Port.

3. Stellen Sie die Stromversorgung an, indem Sie die schwarze PWR-Taste neben dem

LAN1-Ethernet-Port drücken.

- 10 -

4. Befestigen Sie das Gehäuse mit der mitgelieferten Schraube auf der Halterung.

5. Stecken Sie das Stromkabel in den DC-Port des PoE-Injektors.

6. Verbinden Sie das andere Ende des Cat.5/5e/6 Kabel mit dem PoE-Port des PoE-Injektors.

Die Installation ist nun beendet und sollte dem folgenden Bild entsprechen.

Otros manuales para WAB-5120

1

Tabla de contenidos

Idiomas:

Otros manuales de Punto de acceso inalámbrico de LevelOne

LevelOne

LevelOne WAP-6002 Manual de usuario

LevelOne

LevelOne WAP-3101 Manual de usuario

LevelOne

LevelOne WAB-1000 Manual de usuario

LevelOne

LevelOne WAP-6017 Manual de usuario

LevelOne

LevelOne WAB-7400 Manual de usuario

LevelOne

LevelOne WAP-6101 Manual de usuario

LevelOne

LevelOne WAP-6012 Manual de usuario

LevelOne

LevelOne WAB-5010 Manual de usuario

LevelOne

LevelOne WAP-6102 Manual de usuario

LevelOne

LevelOne WAP-8121 Manual de usuario

LevelOne

LevelOne WAP-6121 Manual de usuario

LevelOne

LevelOne EAP-110 Manual de usuario

LevelOne

LevelOne WAP-0005 Manual de usuario

LevelOne

LevelOne WAB-6120 Manual de usuario

LevelOne

LevelOne WAB-6121 Manual de usuario

LevelOne

LevelOne WAP-6121 Manual de usuario

LevelOne

LevelOne PLI-3411 Manual de usuario

LevelOne

LevelOne WAP-6117 Manual de usuario

LevelOne

LevelOne EAP-300 Manual de usuario

LevelOne

LevelOne WAP-6003 Manual de usuario

LevelOne

LevelOne WBR-3400TX Manual de usuario

LevelOne

LevelOne OAN-4058 Manual de usuario

LevelOne

LevelOne WAB-3002 Manual de usuario

LevelOne

LevelOne WAB-6010 Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario