LevelOne GEL-2060 Guía rápida
http://www.level1.com -1-
GEL-2060
DoS-Attack Prevention Configuration
Commands
Table of Contents
http://www.level1.com - 2-
Table of Contents
Chapter 1 DoS Attack Prevention Configuration Commands ............................................................................................... 3
1.1 DoS-Attack Prevention Configuration Commands ................................................................................................ 3
1.1.1 dos enable................................................................................................................................................. 3
1.1.2 show dos ................................................................................................................................................... 4
DoS Attack Prevention Configuration Commands
http://www.level1.com -3-
Chapter 1 DoS Attack Prevention Configuration
Commands
1.1 DoS-Attack Prevention Configuration Commands
DoS attack prevention configuration commands are shown below:
dos enable
show dos
1.1.1 dos enable
Syntax
dos enable {all | icmp icmp-value | ip | ipv4firstfrag | l4port | mac | tcpflags |
tcpfrag tcpfrag-value}
no dos enable {all | icmp | ip | ipv4firstfrag | l4port | mac | tcpflags | tcpfrag}
Parameter
Parameter
Description
all
Enables to prevent all kinds of DoS attacks.
icmp icmp-value
Prevents the ICMP DoS attacks. Here, the icmp-value
parameter means the maximum length of ICMP packet, whose
default value is 512.
ip
Prevents those DoS attack packets whose source IP addresses
are equal to the destination IP addresses.
ipv4firstfrag
Starts to check the first fragment of IP packet.
l4port
Starts to check the L4 packets whose source port is equal to the
destination port.
mac
Starts to check those packets whose source MACs are equal to
destination MACs.
tcpflags
Starts to check the TCP packets with illegal flags.
tcpfrag tcpfrag-value
Starts to check the DoS attack packet of TCP fragment. Here,
the tcpfrag-value parameter means the minimum TCP header,
whose default value is 20.
Default value
DoS attack prevention is disabled by default.
Remarks
DoS attack prevention is configured in global mode.
The DoS IP sub-function can drop those IP packets whose source IPs are equal to
the destination IPs.
DoS Attack Prevention Configuration Commands
http://www.level1.com -4-
The DoS ICMP sub-function can drop the following two kinds of packets: 1.
ICMPv4/v6 ping packets whose size is larger than icmp-value; 2. ICMP packets.
The DoS l4port sun-function can drop those TCP/UDP packets whose source port
is equal to the destination port.
The DoS MAC sub-function can drop those packets whose source MACs are equal
to destination MACs.
The DoS tcpflags sub-function can drop the following 4 kinds of TCP packets: 1.
TCP SYN flag=1 & source port<1024; 2.TCP control flags = 0 & sequence = 0;
3.TCP FIN URG PSH =1 & sequence = 0; 4.TCP FIN SYN =1.
The DoS tcpfrag sub-function can drop the following two kinds of TCP packets: 1.
The TCP header is smaller than the first TCP fragment of tcpfrag-value; 2. TCP
fragments whose offset values are 1.
Example
The following example shows how to set the global DoS attack prevention function
to prevent those IP packets whose source IPs are destination IP addresses.
Switch_config#dos enable ip
The following example shows how to set DoS attack prevention in global mode to
prevent those packets whose maximum ICMP length is bigger than 255.
Switch_config#dos enable icmp 255
1.1.2 show dos
Syntax
show dos
It is used to show all DoS attack prevention functions that users have set.
Parameter
N/A
Default value
N/A
Remarks
EXEC mode
Example
The following example shows how to display all DoS attack prevention functions.
Switch_config#dos enable all
Switch_config#show dos
dos enable ip
dos enable ipv4firstfrag
dos enable tcpflags
dos enable l4port
dos enable mac
DoS Attack Prevention Configuration Commands
http://www.level1.com -5-
dos enable tcpfrag
dos enable icmp
Switch_config#
The following example shows how to set dos enable icmp to display the
sub-function that users have set.
Switch_config#dos enable icmp
Switch_config#show dos
dos enable icmp
The following example shows how to set dos enable icmp 255 to display the
sub-function that users have set.
Switch_config#dos enable icmp 255
Switch_config#show dos
dos enable icmp 255
Otros manuales para GEL-2060
5
Tabla de contenidos
Otros manuales de Cambiar de LevelOne
LevelOne
LevelOne GSW-1676 Manual de usuario
LevelOne
LevelOne Infinity IES-0920 Manual de usuario
LevelOne
LevelOne IES-0610 V2 Manual de usuario
LevelOne
LevelOne PLI-4251 Manual de usuario
LevelOne
LevelOne ProCon GSW-1290 Manual de usuario
LevelOne
LevelOne GSW-2457 Manual de usuario
LevelOne
LevelOne ViewCon KVM-0850 Manual de usuario
LevelOne
LevelOne GEP - 5271 Manual de usuario
LevelOne
LevelOne IFP-0504 Manual de usuario
LevelOne
LevelOne GEL-2681 Manual de usuario
LevelOne
LevelOne GTL-2880 Manual de usuario
LevelOne
LevelOne GSW-1601TX Manual de usuario
LevelOne
LevelOne GEP-2682 Manual de usuario
LevelOne
LevelOne GEL-2060 Guía rápida
LevelOne
LevelOne KVM-0290 Manual de usuario
LevelOne
LevelOne GES-2451 Manual de usuario
LevelOne
LevelOne GSW-4870TGX Manual de usuario
LevelOne
LevelOne GEL-2670 24 GE + 2 GE SFP Manual de usuario
LevelOne
LevelOne OfficeCon GSW-0841 Manual de usuario
LevelOne
LevelOne KVM-8916 Manual de usuario
