LevelOne IES-0810 Manual de usuario
IES-0810
8 FE Unmanaged Switch -20 to 60, DIN-rail
User Manual
v1.00 -1206
IES-0810 User Manual Page 2
Preface
A member of the growing family of rugged switches, thisswitch addresses a need for a
smallerswitch.Thisswitchprovides an affordable solution for rugged andoutdoor
environment, transportation road-side cabinet, industrial floor shop, multitenant
dwellings or FiberToThe Home (FTTH) applications. Capableof operating at temperature
extremes of -20°C to +60°C,thisis theswitchof choiceforharshenvironments constrained
by space.
Plug-and-PlaySolution:
The switch is aplug-and-playFast Ethernet Switch in compact size. It doesn't have any
complicated software to set up.
Thismanualdescribeshowtoinstallandusethe hardened EthernetSwitch.Thisswitch
integratesfull wirespeedswitchingtechnology.Thisswitchbringsthe answer to
complicatedhardened networking environments.
To get the most out of this manual, you should havean understanding of Ethernet
networking concepts.
In this manual, you will find:
•Features on the switch
•Illustrative LED functions
•Installation instructions
•Specifications
IES-0810 User Manual Page 3
Table of Contents
PREFACE ........................................................................................................................................................ 2
PRODUCT OVERVIEW ................................................................................................................................... 4
HARDENED ETHERNETSWITCH ...............................................................................................................................................................4
PACKAGE CONTENTS ................................................................................................................................................................................4
PRODUCT HIGHLIGHTS.............................................................................................................................................................................5
FRONTPANEL DISPLAY.............................................................................................................................................................................6
INSTALLATION............................................................................................................................................... 7
SELECTING A SITE FORTHE SWITCH.........................................................................................................................................................7
DINRAIL MOUNTING ..............................................................................................................................................................................8
CONNECTINGTOPOWER..........................................................................................................................................................................9
CONNECTINGTOYOUR NETWORK........................................................................................................................................................11
SPECIFICATIONS.......................................................................................................................................... 12
APPENDIX A – CONNECTOR PINOUTS........................................................................................................ 13
IES-0810 User Manual Page 4
Product Overview
Hardened Ethernet Switch
Package Contents
When you unpack the product package, youshall find the items listed below. Please
inspect the contents, andreport any apparent damage or missing items immediately to
your authorized reseller.
•IES-0810
8 FE Unmanaged Switch -20 to 60, DIN-rail
•Quick Installation Guide
•CD User Manual
IES-0810 User Manual Page 5
Product Highlights
Basic Features
•Meets IEC61000-6-2 EMC Generic Standard Immunity for industrial environment.
•Support 802.3/802.3u/802.3X.
•Auto-negotiation: 10/100Mbps, Full/half-duplex;Auto MDI/MDIX.
•Support 2048 MAC addresses.
•Provides 768Kbits memory buffer.
•Alarms for power failure by relay output.
•Operating voltage and Max. current consumption: 1.1A @ 12VDC, 0.55A @ 24VDC.
•Power consumption: 13.2W Max.
•Power Supply: Redundant DCTerminal Block power inputs or 12VDC DC JACKwith
100-240VAC external power supply.
•Supports DIN-Rail, Panel, or RackMounting installation.
IES-0810 User Manual Page 6
Front Panel Display
Basic Features
•PowerStatus (PW1, PW2)
These LEDs come on when the switch is properlyconnected to power and turned on.
‚Port Status LEDs
The LEDs display status for each respective port.
LED Status Description
PW 1,2
(Green) Steady Power On
Off Power Off
10/100Base-TX or 100Base-FX/BX
LNK/ACT
(Green) Steady Network connection is established
Flashing Transmitting or Receiving data
100
(Yellow) Steady Connection at 100Mbps speed
Off Connection at 10Mbps speed
Physical Ports
This switch provides:
Eight 10/100Base-TX ports
Eight 10/100Base-TXports + one 100Base-FXport
Six 10/100Base-TX ports + two 100Base-FX ports
Four 10/100Base-TX ports + four 100Base-FX ports
Connectivity
RJ-45 connector
SCor ST connector on 100Base-FX fiber port
IES-0810 User Manual Page 7
Installation
This chapter gives step-by-step instructions about how to install the switch:
Selecting a Site for the Switch
As with anyelectric device, you should place the switch where it will not be subjected to
extreme temperatures, humidity, or electromagnetic interference. Specifically, the site you
select should meet the following requirements:
•The ambient temperature should be between -20to 60 degrees Celsius.
•The relativehumidity should be less than 95 percent, non-condensing.
•Surrounding electrical devices should not exceed the electromagnetic field (RFC)
standards.
•Make sure that the switch receives adequate ventilation. Do not block the ventilation
holes on each side of the switch
•The power outlet should be within 1.8 meters of the switch.
IES-0810 User Manual Page 8
DIN Rail Mounting
Fix the DIN rail attachment plate to the back panel of the switch.
Installation: Place the switch on the DIN rail fromabove using the slot. Push the front of
the switch toward the mounting surface until it audibly snaps into place.
Removal: Pull out the lower edge and then remove the switch from the DIN rail.
IES-0810 User Manual Page 9
Connecting to Power
Redundant DCTerminalBlockPower Inputs or 12VDC DC Jack (Optional):
Redundant DCTerminal Block Power Inputs
There are two pairs of power inputs can be used to power up this device.You only need to
have one power input connected to run the switch.
Step 1: Connect the DC power cord to the plug-able terminal block on the switch, and
then plug it into a standard DC outlet.
Step 2: Disconnect the power cordif you want to shut down the switch.
12VDC DC Jack (Optional)
Step 1: Connect the supplied AC to DC power adapter to the receptacle onthe topside of
the switch.
Step 2: Connect the power cord tothe AC to DC power adapter and attach the plug intoa
standard ACoutlet with the appropriate ACvoltage.
IES-0810 User Manual Page 10
Alarms for Power Failure
Step 1:There are two pins on the terminal block are used for power failure detection. It
provides the normally closed output when the power source is active. Use this as a dry
contact application to send a signal for power failure detection.
Terminal Block
PW1 + 12 – 30VDC
–
Power Ground
PW2 + 12 – 30VDC
– Power Ground
Earth Ground
Relay Output 1A @ 12 - 30VDC
1. Therelaycontactopensif Power1 or Power2 falls
Special note:
The relay output is normal open position when there is no power to the switch.
Please do not connect anypower source to thisterminal to prevent the shortage to
yourpower supply.
Tabla de contenidos
Otros manuales de Enrutador de red de LevelOne
LevelOne
LevelOne DC-202 Manual de usuario
LevelOne
LevelOne MDU-2400FXC Manual de usuario
LevelOne
LevelOne WBR-6013 Manual de usuario
LevelOne
LevelOne FBR-1403TX Manual de usuario
LevelOne
LevelOne FSW-1650 Manual de usuario
LevelOne
LevelOne WBR-6802 Manual de usuario
LevelOne
LevelOne GTL-2660 Manual de usuario
LevelOne
LevelOne WBR-3406TX Manual de usuario
LevelOne
LevelOne NetCon WBR-3408 Manual de usuario
LevelOne
LevelOne FBR-1700TX Manual de usuario
LevelOne
LevelOne GSW-2457 Manual de usuario
LevelOne
LevelOne WAP-0007 Manual de usuario
LevelOne
LevelOne WAP-0004 Manual de usuario
LevelOne
LevelOne WBR-6003 Manual de usuario
LevelOne
LevelOne GEU-2429 Manual de usuario
LevelOne
LevelOne GEU-0822 Manual de usuario
LevelOne
LevelOne FSW-0511 Manual de usuario
LevelOne
LevelOne FEP-0811 Manual de usuario
LevelOne
LevelOne NetCon FBR-1409TX Manual de usuario
LevelOne
LevelOne GBR-4001 Manual de usuario
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad