Kramer VP-1608 Manual de usuario

Kramer Electronics, Ltd.

Preliminary

USER MANUAL

Model:

VP-1608

16x8 RGBHV/Balanced Audio Matrix

Contents 
 
i
 
i
 
Contents 
Introduction  1 
Getting Started  1 
1 Quick Start  2 
Overview  3 
Your VP-1608 16x8 RGBHV/Balanced Audio Matrix  3 
Installing the VP-1608 in a Rack  7 
Connecting a VP-1608 16x8 RGBHV/Balanced Audio Matrix  8 
1 Connecting the Balanced/Unbalanced Stereo Audio Input/Output  10 
2 Controlling via RS-232 (for example, using a PC)  10 
3 Controlling via RS-485 11 
4 Setting the MACHINE # DIP-Switches  12 
5 Setting the DELAY DIP-switches  13 
Controlling 16x8 RGBHV/Balanced Audio Matrix Units  13 
1 Controlling from a PC or Serial Controller  13 
2 Controlling via an RS-485 Controller  14 
Operating Your VP-1608 16x8 RGBHV/Balanced Audio Matrix 17 
1 Choosing the Audio-Follow-Video or Breakaway Option  17 
1.1 Setting the Audio-Follow-Video Option 17 
1.2 Setting the Breakaway Option  18 
2 Switching OUT-IN Combinations  18 
3 Confirming Settings  18 
3.1 Toggling between the AT ONCE and CONFIRM Modes  19 
3.2 Confirming a Switching Action  19 
4 Storing/Recalling Input/Output Configurations  19 
4.1 Storing an Input/Output Configuration  20 
4.2 Recalling an Input/Output Configuration  20 
4.3 Deleting an Input/Output Configuration  20 
5 Adjusting the Audio Gain Control  20 
6 Locking and Unlocking the Front Panel  21 
7 Resetting the VP-1608 16x8 RGBHV/Balanced Audio Matrix  21 
7.1 Resetting to the Current Status  21 
7.2 Resetting to the Factory Default State  21 
8 Displaying Unit Characteristics  22 
Flash Memory Upgrade  22 
1 Downloading from the Internet  22 
2 Connecting the PC to the RS-232 Port 23 
3 Upgrading the Firmware  23 
Technical Specifications  28 

KRAMER:  SIMPLE CREATIVE TECHNOLOGY 
Contents 
 
ii 
11 3Table of Hex Codes for Serial Communication  29 
12 Hex Tables for Audio Input/Output Gain Control 30 
12.1 Hex Tables for Audio Input Gain Control 30 
12.2 Hex Tables for Audio Output Gain Control  32 
13 Kramer Protocol 2000  34 
Figures 
Figure 1: VP-1608 16x8 RGBHV/Balanced Audio Matrix  4 
Figure 2: VP-1608 Underside Flash Program Switches  6 
Figure 3: Connecting the VP-1608  9 
Figure 4: Connecting the Balanced Stereo Audio Input/Output  10 
Figure 5: Connecting the Unbalanced Stereo Audio Input  10 
Figure 6: Connecting an Unbalanced Stereo Audio Output  10 
Figure 7: Connecting a PC Without Using a Null-Modem Adapter 11 
Figure 8: Controlling via RS-485 (for example, using an RC-3000) 12 
Figure 9: Control Configuration via RS-232 and RS-485 14 
Figure 10: Controlling via an RS-485 Controller  16 
Figure 11: DIP-Switch Setup on a Single Machine 17 
Figure 12: VP-1608 Unit Characteristics  22 
Figure 13: VP-1608 Underside Flash Program Switches Set for Upgrade  23 
Figure 14: Splash Screen  24 
Figure 15: Atmel – Flip Window 24 
Figure 16 Device Selection Window  24 
Figure 17: Device Selection Window  25 
Figure 18: Loading the Hex  25 
Figure 19: RS-232 Window 26 
Figure 20: Atmel – Flip Window (Connected)  26 
Figure 21: Atmel – Flip Window (Operation Completed)  27 
 
Tables 
Table 1: Front Panel VP-1608 16x8 RGBHV/Balanced Audio Matrix Features  5 
Table 2: Rear Panel VP-1608 16x8 RGBHV/Balanced Audio Matrix Features  6 
Table 3: VP-1608 Underside (Flash Program Switches) Features  6 
Table 4: MACHINE # DIP-switch Settings 12 
Table 5: DELAY DIP-switch Settings 13 
Table 6: Technical Specifications of the VP-1608 28 
Table 7: VP-1608 Hex Codes for Switching via RS-232/RS-485 in Breakaway Mode  29 
Table 8: VP-1608 Hex Codes for Audio Input Gain Control  31 
Table 9: VP-1608 Hex Codes for Audio Output Gain Control  33 
Table 10: Protocol Definitions 34 
Table 11: Instruction Codes for Protocol 2000  35 
 

Introduction

1 Introduction

Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been

providing a world of unique, creative, and affordable solutions to the vast

range of problems that confront the video, audio, presentation, and

broadcasting professional on a daily basis. In recent years, we have

redesigned and upgraded most of our line, making the best even better! Our

1,000-plus different models now appear in 11 groups1

Thank you for purchasing your Kramer VP-1608 16x8 RGBHV/Balanced

Audio Matrix that is ideal for the following typical applications:

that are clearly

defined by function.

 Any professional system requiring outstanding value in a 16x8

matrix

 Production and duplications facilities

The package includes the following items:

 VP-1608 16x8 RGBHV/Balanced Audio Matrix

 Power cord, null-modem adapter and IR remote control

 Windows®-based Kramer control software

 This user manual2

2 Getting Started

We recommend that you:

 Unpack the equipment carefully and save the original box and

packaging materials for possible future shipment

 Review the contents of this user manual

 Use Kramer high-performance high-resolution cables3

1 GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Matrix Switchers; GROUP 3: Control Systems;

GROUP 4: Format/Standards Converters; GROUP 5: Range Extenders and Repeaters; GROUP 6: Specialty AV Products;

GROUP 7: Scan Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9: Room Connectivity;

GROUP 10: Accessories and Rack Adapters; GROUP 11: Sierra Products

2 Download up-to-date Kramer user manuals from our Web site: http://www.kramerelectronics.com

3 The complete list of Kramer cables is on our Web site at http://www.kramerelectronics.com

KRAMER: SIMPLE CREATIVE TECHNOLOGY

Getting Started

2.1 Quick Start

This quick start chart summarizes the basic setup and operation steps.

Overview

3 Overview

The VP-1608 16x8 RGBHV/Balanced Audio Matrix is a true matrix

switcher, routing any input to any or all outputs. The VP-1608 includes 16

input and 8 output selector buttons.

The unit features:

 A bandwidth of 400MHz (fully loaded) for RGB signals

 A unique vertical and horizontal sync-pulse solution

 Audio-follow-video or audio breakaway option (to switch audio

independently from video)

 15 preset memory locations for quick access to common

configurations

 A “TAKE” button for precise switch control, letting you place

multiple switches in a queue, and then activate them, with one

touch of this button or a single serial command

 A delayed switching mode (ranging from 0 to 3.5sec1

Control the VP-1608 using the front panel buttons, or remotely via:

), for clean

transitions when switching between non-genlocked sources

 RS-485 or RS-232 serial commands—that also support audio gain

adjustments for each input and output—transmitted by a touch

screen system, PC, or other serial controller

 The Kramer RC-IR2 Infrared Remote Control Transmitter

The VP-1608 is dependable, rugged and fits into three vertical spaces (3U)

of a standard 19" rack. To achieve the best performance:

 Connect only good quality connection cables, thus avoiding

interference, deterioration in signal quality due to poor matching,

and elevated noise levels (often associated with low quality

cables)

 Avoid interference from neighboring electrical appliances and

position your Kramer VP-1608 away from moisture, excessive

sunlight and dust

4 Your VP-1608 16x8 RGBHV/Balanced Audio Matrix

Figure 1 illustrates the front and rear panels of the VP-1608. Table 1 and

Table 2 define the front and rear panels of the VP-1608, respectively.

1 In increments of 0.5sec

KRAMER: SIMPLE CREATIVE TECHNOLOGY

Your VP-1608 16x8 RGBHV/Balanced Audio Matrix

Figure 1: VP-1608 16x8 RGBHV/Balanced Audio Matrix

Your VP-1608 16x8 RGBHV/Balanced Audio Matrix

Table 1: Front Panel VP-1608 16x8 RGBHV/Balanced Audio Matrix Features

Feature

Function

1 IR Receiver The red LED is illuminated when receiving signals from the Kramer

Infra-red remote control transmitter

2 POWER Switch Illuminated switch supplying power to the unit

3 OUTPUT SELECTOR Buttons Select the output to which the input is switched (from 1 to 8)

4 INPUT SELECTOR Buttons

Select the input to switch to the output (from 1 to 16)

5 OFF Button Pressing OFF after pressing an OUTPUT button disconnects that

output from the inputs. To disconnect all the outputs, press the ALL

button and then the OFF button

6 ALL Button Pressing ALL followed by an INPUT button, connects that input to

all outputs2

TAKE Button Pressing TAKE toggles the mode between the CONFIRM mode

and the AT ONCE mode (user confirmation per action is unnecessary)

VIDEO Button When pressed actions relate to video

9 AUDIO Button When pressed actions relate to audio

10 AFV Button When pressed audio channels follow the video channels. The button

is illuminated when the AFV mode is selected

11 STO Button Pressing STO (STORE) followed by an input button stores the

current setup

12 RCL Button Pressing the RCL (RECALL) button and the corresponding input

button recalls a setup

After pressing the button, the stored status flashes. Pressing a

different input button lets you view4

another setup. After making

your choice, pressing the RCL button again implements the new

status

LOCK Button Pressing the LOCK button for more than 2 seconds,

engages/disengages the front panel switches

14 INPUT STATUS 7-segment

Display

Displays the selected input switched to the output (marked above

each input)5

1 The INPUT SELECTOR buttons are also used to store/recall the input/output configurations (refer to section 8.4)

2 For example, press ALL and then INPUT button # 2 to connect input # 2 to all the outputs

3 When in Confirm mode, the TAKE button illuminates

4 Only view, nothing is implemented at this stage

5 Also displays the number included in the product name and the firmware version number, as section 8.8 describes

KRAMER: SIMPLE CREATIVE TECHNOLOGY

Your VP-1608 16x8 RGBHV/Balanced Audio Matrix

Table 2: Rear Panel VP-1608 16x8 RGBHV/Balanced Audio Matrix Features

Feature

Function

15 AUDIO OUT Terminal Block Connectors Connect to the audio acceptors (from 1 to 8)

16 RS-232 9-pin D-sub (F) Connector Connects to the PC or other Serial Controller

17 Setup DIP-switches DIPS 1, 2, and 3 for setup of the Machine #; DIP

4 for RS-485 termination

18 RS-485 Connector RS-485 port on detachable terminal block

19 DELAY DIP-switches DIP-switches for setup of the delay time1

Power Connector with Fuse AC connector enabling power supply to the unit

21 V (Vertical Sync) OUTPUT BNC Connectors

Connect to the RGBHV video acceptors (1 to 8)

22 H (Horizontal Sync) OUTPUT BNC Connectors

23 B OUTPUT BNC Connectors

24 G OUTPUT BNC Connectors

25 R OUTPUT BNC Connectors

26 R INPUT BNC Connectors

Connect to the RGBHV video sources (1 to 16)

27 G INPUT BNC Connectors

28 B INPUT BNC Connectors

29 H (Horizontal Sync) INPUT BNC Connectors2

30 V (Vertical Sync) INPUT BNC Connectors2

31 AUDIO INPUTS Terminal Block Connectors Connect to the audio sources (from 1 to 16)

Figure 2 and Table 3 define the two flash program switches3

on the

underside of the VP-1608 unit:

Figure 2: VP-1608 Underside Flash Program Switches

Table 3: VP-1608 Underside (Flash Program Switches) Features

Feature

Function

1 Flash Program Switch 1 Move to the right for Program3, or move to the left for Normal4

Flash Program Switch 2 Move to the right for Reset

, or move to the left for Normal

1 Ranging from 0sec to 3.5sec (in increments of 0.5sec)

2 For RGBS applications, one of the sync channels (H or V) may be used for the S channel

3 Used to upgrade to the latest Kramer firmware (see section 8.8)

4 The factory default

Installing the VP-1608 in a Rack

5 Installing the VP-1608 in a Rack

This section describes how to install the VP-1608 in a rack.

Before Installing in a rack How to Rack Mount

Before installing in a rack, be sure that the environment is

within the recommended range:

To rack-mount a machine:

1. Attach both ear brackets to the

machine. To do so, remove the

screws from each side of the

machine (5 on each side), and

replace those screws through the

ear brackets.

2. Place the ears of the machine

against the rack rails, and insert the

proper screws (not provided)

through each of the four holes in the

rack ears.

Note that:

 In some models, the front panel

may feature built-in rack ears

 Detachable rack ears can be

removed for desktop use

 Always mount the machine in the

rack before you attach any cables

or connect the machine to the

power

 If you are using a Kramer rack

adapter kit (for a machine that is not

19"), see the Rack Adapters user

manual for installation instructions

(you can download it at:

http://www.kramerelectronics.com)

Operating temperature range +5 to +45 C (41 to 113 F)

Operating humidity range 10 to 90% RHL, non-condensing

Storage temperature range -20 to +70 C (-4 to 158 F)

Storage humidity range 5 to 95% RHL, non-condensing

CAUTION!!

When installing on a 19" rack, avoid hazards by taking

care that:

1. It is located within the recommended environmental

conditions, as the operating ambient temperature of a

closed or multi unit rack assembly may exceed the

room ambient temperature.

2. Once rack mounted, enough air will still flow around

the machine.

3. The machine is placed straight in the correct

horizontal position.

4. You do not overload the circuit(s). When connecting

the machine to the supply circuit, overloading the

circuits might have a detrimental effect on overcurrent

protection and supply wiring. Refer to the appropriate

nameplate ratings for information. For example, for

fuse replacement, see the value printed on the

product label.

5. The machine is earthed (grounded) in a reliable way

and is connected only to an electricity socket with

grounding. Pay particular attention to situations where

electricity is supplied indirectly (when the power cord

is not plugged directly into the socket in the wall), for

example, when using an extension cable or a power

strip, and that you use only the power cord that is

supplied with the machine.

Otros manuales para VP-1608

Tabla de contenidos

Otros manuales de Conmutador de matriz de Kramer

Kramer

Kramer VP-725DS Manual de usuario

Kramer

Kramer VP-778 Manual de usuario

Kramer

Kramer VS-5x5 Manual de usuario

Kramer

Kramer 88HD Manual de usuario

Kramer

Kramer VS-88UHDA Manual de usuario

Kramer

Kramer XL 1616V4 Manual de usuario

Kramer

Kramer Sierra Video 3232V5 Manual de usuario

Kramer

Kramer VP-16x18AK Manual de usuario

Kramer

Kramer 88DEE Manual de usuario

Kramer

Kramer MTX3-34-M Manual de usuario

Kramer

Kramer XL 3232VS Manual de usuario

Kramer

Kramer XL 3232V Manual de usuario

Kramer

Kramer Sierra Pro XL 1616V3 Manual de usuario

Kramer

Kramer VP-32XLN Manual de usuario

Kramer

Kramer Sierra Video 3232SXL Manual de usuario

Kramer

Kramer VS-88HCB Manual de usuario

Kramer

Kramer VP-1608 Manual de usuario

Kramer

Kramer VS-88HN Manual de usuario

Kramer

Kramer VP-8x8 Manual de usuario

Kramer

Kramer VS-88HD Manual de usuario

Kramer

Kramer 3232HD Manual de usuario

Kramer

Kramer Sierra Pro XL 1208V5S Manual de usuario

Kramer

Kramer VS-42HN Manual de usuario

Kramer

Kramer Sierra Video 1208V5 Manual de usuario

Manuales populares de Conmutador de matriz de otras marcas

Broadcast Tools

Broadcast Tools SS 8.2 Manual de usuario

Altimium

Altimium MATF32 Manual de usuario

ALFAtron

ALFAtron ALF-MUK44N Manual de usuario

Monoprice

Monoprice Blackbird 15377 Manual de usuario

PTN

PTN FMX12 Manual de usuario

CYP

CYP nT15GX01 Manual de usuario

TESmart

TESmart HMA0402A40 Manual de usuario

Octava

Octava HD4XSTPMX Manual de usuario

Intelix

Intelix FLX-88 Instrucciones de funcionamiento

Roland

Roland XS-1HD Manual de usuario

Atlona

Atlona AT-HDMI-22M Manual de usuario

Link

Link HD8X8 Manual de usuario

AMX

AMX AVS-OP-2020-117 Instrucciones y recetas

Lindy

Lindy 38042 Manual de usuario

Extron electronics

Extron electronics MTPX Plus Series Manual de usuario

Key Digital

Key Digital Champion KD-16x16CS Manual de usuario

Shinybow USA

Shinybow USA SB-8811 Manual de usuario

Optimus

Optimus Compact Manual de usuario