Kichler Lighting Meredith Manual de usuario

MeredithTM

Includes our new

CoolTouchTM Control System

Looks permanent, but goes wherever you go!

U.S. Patent Pending

Kichler®Lighting

7711 East Pleasant Valley Road

P.O. Box 318010

Cleveland, Ohio 44131-8010

Customer Service

866.558.5706

8:30 AM to 5:00 PM EST,

Monday - Friday

A Kichler®Décor™ceiling fan

Designed to coordinate with a popular Kichler Lighting collection.

Instruction Manual

KHA9090103

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

3. WARNING: To reduce the risk of electrical

5. The outlet box and support structure must

be securely mounted and capable of

reliably supporting a minimum of 50

pounds. Use the outlet boxes marked

6. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the floor.

7. To operate the reverse function on this fan,

press the reverse button while the fan is

running.

8. Avoid placing objects in the path of the

blades.

9. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

10. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After marking electrical connections,

spliced conductors should be turned

upward and pushed carefully up into outlet

box. The wires should be spread apart with

12. Electrical diagrams are for reference only.

Light kits that are not packed with the fan

must be marked suitable for use with the

Instructions packaged with the light kits and

switches for proper assembly.

1. SAFETY RULES

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT FAN TO

OUTLET BOX MARKED "ACCEPTABLE FOR FAN

WARNING

All wiring must be in accordance with the

National Electrical Code, ANSI/NFPA70-1999

and local electrical codes. Electrical installa-

tion should be performed by a qualified

licensed electrician.

WARNING: To reduce the risk of fire,

electric shock, or personal injury, mount

this fan to outlet box marked "Acceptable

for Fan Support" and use mounting

screws provided with the outlet box. Most

outlet boxes commonly used for the sup-

port of light fixtures are not acceptable for

fan support and may need to be replaced.

Due to the complexity of the installation of

this fan, a qualified licensed electrician is

strongly recommended.

conductor of a fan identified as grounded

condutor to be connected to a grounded

conductor of power supply, conductor of fan

identified as ungrounded conductor to be

connected to an ungrounded conductor of

power supply,conductor of fan identified for

equipment grounding to be connected to an

equipment-grounding conductor.

breaker or fuse box before cleaning and

shock and fire, do not use this fan with

any solid-state fan speed control device.

TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADE BRACKETS WHEN

INSTALLING THE BRACKETS, BALANCING THE

BLADES, OR CLEANING THE FAN. DO NOT

INSERT FOREIGN OBJECTS IN BETWEEN ROTAT-

ING FAN BLADES.

maintenace, or attempting Installation.

SUPPORT."

"FOR FAN SUPPORT."

model fan you are installing. Refer to the

3. PACKAGE CONTENTS

Unpack your fan and check the contents. You

should have the following items:

Philips screw driver

Slot screw driver

11 mm wrench

Step ladder

Wire cutters

2. TOOLS AND MATERIALS REQUIRED

MeredithTM

a. Fan blades (5)

b. Mounting bracket

c. Canopy

d. Ball/downrod assembly (1)

& extra downrod (1)

e. Coupling cover

f. Fan assembly

g. Decorative arm

h. Set of blade brackets (5)

i. Mounting plate

j. Switch housing

k. Light kit

l. Glass bowl

m. Receiver +7 wire nuts

n. CoolTouch™ Control System

o. Bulbs (3)

p. Package hardware:

1) Mounting hardware:

a. wood screws (2), flat washers(2),

screws(2), wire nuts(4)

2) Blade attachment hardware:

a. screws (16); flat washers(16);

fiber washers(16)

3) Blade bracket hardware:

a. screws (1)

4) Safety cable hardware:

a. wood screw (1); spring washer (1);

flat washer (1)

5) Balance kit

q. Decorative plate hardware:

a. decorative plate (1); finial (1);

light kit hardware (1)

4. MOUNTING OPTIONS

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 50 lbs). Do

not use plastic outlet boxes.

Figures 1,2 and 3 are examples of different

ways to mount the outlet box.

NOTE: You may need a longer downrod to

maintain proper blade clearance when

installing on a steep, sloped ceiling. (Fig. 3)

To hang your fan where there is an existing

fixture but no ceiling joist, you may need a

joist hanging bracket as shown in Fig 4.

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

Fig. 1

Fig. 3

Fig. 4

Outlet box

Fig. 2

If there isn't an existing UL ( CUL for Canadian

Installation) listed mounting box, then read the

following instructions. Disconnect the power by

removing fuses or turning off circuit breakers.

MeredithTM

5. HANGING THE FAN

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly:

Step 2. Secure the mounting bracket to the

ceiling outlet box using screws and washers

provided with the outlet box. (Fig. 6)

Step 4. Loosen the two set screws and

remove the hitch pin and lock pin from

the motor coupling assembly. (Fig. 8)

Step 1. Remove the fan motor and housing

assembly from the protective plastic bag and

take the lower styrofoam packing pad out of

the carton. Place the styrofoam pad on the

floor, then place the fan assembly into the

styrofoam pad with the bottom of the motor

facing up. (The styrofoam pad serves as a

holder for the fan during the first stages of

assembly). Remove the plastic motor shipping

blocks and discard. (Fig. 5)

Step 3. Use a screwdriver to loosen the

cross pin and remove it from downrod

assembly. Loosen the set screw and rotate

the hanger ball off the downrod. (Fig. 7)

Step 5. Carefully feed fan electrical wires up

through the downrod. Thread the downrod

onto the motor coupling until the hitch pin

holes are aligned. Next, replace hitch pin and

lock pin, and tighten both set screws. (Fig. 8)

Fig. 7

Fig. 5

Fig. 6

Fig. 8

shipping block

Screw

Fan housing

Mounting bracket

CUL listed electrial box

Mounting screw

120V wires

Washer

Set screw

Downrod

Hanger Ball

Cross Pin Set Screw

Hitch pin

Lock pin

Downrod

Fig. 10

Registration slot

Step 7. Now lift the motor assembly into

position and place the hanger ball into the

hanger bracket. Rotate until the “Check Tab”

has dropped into the “Registration Slot” and

seats firmly. (Fig. 10) The entire motor

assembly should not rotate if this is done

correctly.

Step 6. Slip the coupling cover, decorative

arm, canopy cover and canopy onto the

downrod. Reinstall the hanger ball onto the

downrod and make sure the cross pin is in

place and the set screw on hanger ball is

tight. Secure the decorative arm assemble

(with the lower ends resting on the top of

the ceiling fan) by tightening the set screw.

(Fig. 9)

NOTE: The entire motor assembly should

not rotate if this is done correctly.

NOTE: Please make sure all set screws

are in place and tight before installation

the following steps.

Fig. 9

Set screw

Canopy cover

Downrod

Canopy

Decorative arm Coupling cover

MeredithTM

Fig. 12

Fig. 13

Code switch

Receiver

Hanger

bracket

Battery Compartment

6. INSTALLATION OF SAFETY SUPPORT

( For Canadian Installation ONLY )

7. MAKE THE ELECTRIC CONNECTIONS

A safety support cable is provided to help prevent

the ceiling fan from failing, please install it as

follows.

Step 1. Attach the provided wood screw and

washers to the ceiling joist next to the mounting

bracket but do not tighten. (Fig. 11-1)

Step 2. Adjust the length of the safety cable to

reach the screw and washers by pulling the extra

cable through the cable clamp until the overall

length is correct, put the end of the cable back

through the cable clamp, forming a loop at the

end of the cable. Tighten the cable clamp

securely. Now, put the loop in the end of the

safety cable over the wood screw and under the

washer. Tighten the wood screw securely. See

Fig. 11-2

WARNING: To avoid possible electrical shock,

be sure the electricity is turned off at the main

circuit breaker or fuse box before wiring.

WARNING: If your house wires are different

colors than referenced in this manual, stop

immediately. A professional electrician is recom-

mended to determine proper wiring.

NOTE: The CoolTouch™ Control System is

equipped with 16 code combinations to prevent

possible interference from or to other remote

units. The frequency switches on your receiver

and transmitter have been preset at the factory.

Please recheck to make sure the switches on

the transmitter and receiver are set to the same

position, any combination of setting will operate

the fan as long as each switch on the transmitter

and receiver are set to the same opposition.

(Fig. 12) Changing the order of switches on

each switch block, changes the operational

frequency.

Step 1. Insert the receiver into the mounting

bracket, with the flat toward the ceiling. (Fig. 13)

Step 2. Motor to Receiver Electrical Connec-

tions:

NOTE: Make all of the following connections

with “Wire Nut” connectors.

Connect the black wire from the fan to black

wire marded “TO MOTOR L” from the receiver.

Connect the white wire from the fan to the white

wire marked “TO MOTOR N” from the receiver.

Connect the blue wire from the fan to the blue

wire marked “For Bottom Light” from the

receiver. Place a plastic wire nut on the end of

the Orange Wire coming from the receiver

marked “For Upper Light”. Your ceiling fan is not

equipped with a Upper Light. Secure all the wire

connections with the plastic wire nut provided.

(Fig. 14 on the next page)

Fig. 11-2

Fig. 11-1

Ceiling

Support Brace

Outlet Box

Wood Screw

Flat Washer

Spring Washer

Wood Screw

Safety Cable bolt

Fig. 14

Fig. 15

8. INSTALLING THE CEILING CANOPY

Step 3. Remote Receiver to Outlet Box Electri-

cal Connections: Connect the black

(hot) wire from the ceiling to the black wire

marked "AC in L" from the receiver. Connect

the white(neutral) wire from the ceiling to the

white wire marked "AC in N" from the

Receiver. Secure the wire connections with

the plastic wire nuts provided. (Fig. 14)

Step 4. If your outlet box has a ground wire

(green or bare copper) connect it to the fan

ground wires. Secure the wire connection with

a plastic nut provided.

NOTE: Carefully tuck the wire connections up

into the outlet box. (Fig. 14)

NOTE: The transmitting unit must be installed

at a maximum distance of 30 feet from the

ceiling fan for proper signal transmission

between the transmitting unit and the fan’s

receiving unit.

WARNING: One last time, make sure the “Check

Tab” at the bottom of the hanger bracket is prop-

erly seated in the “Registration Slot” on the side

of the hanger ball before attaching the canopy to

the bracket. Failure to properly seat the “Check

Tab” could damage the electrical wires when the

ceiling fan blade direction is changed while the

fan is running.

Step 1. Make sure all of the electrical connec-

tions are tucked neatly into ceiling outlet box.

Step 2. Slide the canopy up to ceiling fan and

onto the two screws on hanger bracket. Rotate

the canopy clockwise and tighten the two screws.

Next, while holding the canopy with one hand,

slide the canopy cover over the screws and

rotate clockwise until tight.

NOTE: You may need to adjust the canopy

mounting screws as necessary until the canopy

and canopy cover have a snug fit. (Fig. 15)

Canopy cover

Canopy

Screw

Hanger bracket

Outlet box

Outlex box

Black (hot)

Black("AC" IN L")

Receiver

Black ("to motor L")

Blue ( for bottom light)

Orange (For upper light)

Black (motor)

White (neutral)

Green or bare

White("to motor N")

Copper (ground)

White("AC IN N")

Ground wire

Blue(motor)

White (neutral)

MeredithTM

9. ATTACHING THE FAN BLADES

Fig. 16

Fig. 17

Fig. 18

10. INSTALLATING THE MOUNTING PLATE

Step 1 Attach the blade to the blade bracket

using the screws, washers and fiber washers

as shown in Figure 16. Start screw into

bracket. Repeat for the two remaining screws.

Step 2. Make sure the blade is straight and

tighten each screw until the fiber washer is

slightly compressed and all three screws are

secure.

Step 3. Fasten blade assembly to motor using

"pre-installed" mounting screws in the blade

bracket . (Fig. 17)

Step 2. Place the key holes on the mounting

place over the remaining 2 screws on the

mounting ring, turn mounting plate until it locks

in place at the narrow section of the key holes.

Secure by tightening 2 screws and reinstalling

the third screw. (Fig. 17)

NOTE: If you would like to install the light

fixture that come with your ceiling fan, please

skip to step 12 and continue. If you want your

ceiling fan installed without the light fixture,

follow step 11 and then skip to Step 14.

Step 1. Remove 1 of the 3 screws on the

mounting ring and loosen the other 2 screws.

Blade bracket

Screw

Connection plug

Mounting plate

Metal washer

Screw

Silicon washer

Blade

Blade bracket

Do not remove the mounting ring located on

the motor shaft.

Fig. 20

Fig. 19

12. INSTALLING THE LIGHT KIT

11. INSTALLING THE SWITCH HOUSING

Mounting plate

Connection plug

Switch housing

Plastic nut

White wire

Black wire

Isolation plate

Nut

Lock washer

Metal washer

Capacitor

Reverse

module

Limiter

LIGHT/BLACK

PowerLimit

Max.190W(ON/OFF)

IncandescentorBallast

ACIN L/RED

ACINN/WHITE

ModelNo:PL-190B

AC120V 60HZ

NOTE: Before continuing, make sure the power

is disconnected by turning off the circuit breaker

Step 1. Loosen the 3 screws on the switch

house mounting plate.

Step 2. The square plastic wiring connector

from the ceiling fan and the light fixture will only

fit together one way. Match up the color on the

side of the connector, then push them together

until the snap engages.

Step 3. Tuck the connections neatly into the

switch housing. Align the key holes on the

switch housing with the screws on the mounting

plate. Turn the switch housing until it locks in

place at the narrow end of the key holes.

Tighten all 3 screws previously loosened.

(Fig. 19)

Step 1. Remove the finial NUT located in the

center of the switch housing. See Fig. 20.

Step 2. Remove the lock washer, metal washer

and hex nut from the light fixture mounting

stem.

Step 3. Feed the electrical wires from the light

fixture through the hole in the switch housing

(starting with the black wire first, it has a larger

switch housing, add the metal washer, lock

washer and hex nut on the inside of the switch

housing and tighten securely.

NOTE: Please take the reverse module, capaci-

tor and 190w power limiter out of the switch

housing prior to threading the light kit to switch

housing.

or removing the fuse at the circuit box.

connector). Thread the light kit onto the

Tabla de contenidos

Otros manuales de Admirador de Kichler Lighting

Kichler Lighting

Kichler Lighting Ried 300356 Manual de usuario

Kichler Lighting

Kichler Lighting Szeplo II Manual de usuario

Kichler Lighting

Kichler Lighting VASSAR Manual de usuario

Kichler Lighting

Kichler Lighting 54 Meredith Manual de usuario

Kichler Lighting

Kichler Lighting Tide Weather+ Manual de usuario

Kichler Lighting

Kichler Lighting Spyn Manual de usuario

Kichler Lighting

Kichler Lighting Hatteras Bay Patio Manual de usuario

Kichler Lighting

Kichler Lighting Arkwet Weather+ Manual de usuario

Kichler Lighting

Kichler Lighting Leeds Manual de usuario

Kichler Lighting

Kichler Lighting Chicago Manual de usuario

Kichler Lighting

Kichler Lighting 300026 Manual de usuario

Kichler Lighting

Kichler Lighting 65" GENTRY Manual de usuario

Kichler Lighting

Kichler Lighting Selectlight fixture Manual de usuario

Kichler Lighting

Kichler Lighting Bentzen Manual de usuario

Kichler Lighting

Kichler Lighting Decor Dorset Manual de usuario

Kichler Lighting

Kichler Lighting Guardian 330057 Manual de usuario

Kichler Lighting

Kichler Lighting FRYST Manual de usuario

Kichler Lighting

Kichler Lighting XETY LED Manual de usuario

Kichler Lighting

Kichler Lighting Select Sutter Place Manual de usuario

Kichler Lighting

Kichler Lighting Lehr Decor 80" Manual de usuario

Kichler Lighting

Kichler Lighting Grace 300316 Manual de usuario

Kichler Lighting

Kichler Lighting 330015WH Manual de usuario

Kichler Lighting

Kichler Lighting 35166 Manual de usuario

Kichler Lighting

Kichler Lighting FLYY 310700MWH Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje