Keysight Technologies S9106AC-2IF Guía del usuario

Startup Guide

Keysight

S9106AC-2IF and S9106AC-4UP

5G FR1 Multi-port

TransceiverSolutions

KeysightS9106AC-2IF 5GFR1Multi-portTransceiver

contains:twoTransceivers, 380MHzto6GHz,

withMIMOSubsystem and7to15GHzHighIF

KeysightS9106AC-4UP 5GFR1Multi-portTransceiver

contains:fourTransceivers, 380MHzto6GHz,

withMIMOSubsystem

Notices

No part of this manual may be

reproduced in any form or by any

means (including electronic storage

and retrieval or translation into a foreign

language) without prior agreement and

written consent from Keysight

Technologies, Inc. as governed by

United States and international

Manual Part Number

S9106-90001

Edition

Edition 1, January, 2022

Printed in USA

Published By

Keysight Technologies

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Warranty

THE MATERIAL CONTAINED IN THIS

DOCUMENT IS PROVIDED “AS IS,” AND

IS SUBJECT TO BEING CHANGED,

WITHOUT NOTICE, IN FUTURE

EDITIONS. FURTHER, TO THE

MAXIMUM EXTENT PERMITTED BY

APPLICABLE LAW, KEYSIGHT

DISCLAIMS ALL WARRANTIES, EITHER

EXPRESS OR IMPLIED, WITH REGARD

TO THIS MANUAL AND ANY

INFORMATION CONTAINED HEREIN,

INCLUDING BUT NOT LIMITED TO THE

IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE. KEYSIGHT

SHALL NOT BE LIABLE FOR ERRORS

OR FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES IN

CONNECTION WITH THE

FURNISHING, USE, OR

PERFORMANCE OF THIS DOCUMENT

OR OF ANY INFORMATION CONTAINED

HEREIN. SHOULD KEYSIGHT AND THE

USER HAVE A SEPARATE WRITTEN

AGREEMENT WITH WARRANTY TERMS

COVERING THE MATERIAL IN THIS

DOCUMENT THAT CONFLICT WITH

THESE TERMS, THE WARRANTY

TERMS IN THE SEPARATE

AGREEMENT SHALL CONTROL.

KEYSIGHT TECHNOLOGIES DOES NOT

WARRANT THIRD-PARTY SYSTEM-

LEVEL (COMBINATION OF CHASSIS,

CONTROLLERS, MODULES, ETC.)

PERFORMANCE, SAFETY, OR

REGULATORY COMPLIANCE, UNLESS

SPECIFICALLY STATED.

Technology Licenses

The hardware and/or software

described in this document are

furnished under a license and may be

used or copied only in accordance with

the terms of such license.

U.S. Government Rights

The Software is “commercial computer

software,” as defined by Federal

Acquisition Regulation (“FAR”) 2.101.

Pursuant to FAR 12.212 and 27.405-3

and Department of Defense FAR

Supplement (“DFARS”) 227.7202, the

U.S. government acquires commercial

computer software under the same

terms by which the software is

customarily provided to the public.

Accordingly, Keysight provides the

Software to U.S. government customers

under its standard commercial license,

which is embodied in its End User

License Agreement (EULA), a copy of

which can be found at

http://www.keysight.com/find/sweula. The

license set forth in the EULA represents

the exclusive authority by which the

U.S. government may use, modify,

distribute, or disclose the Software. The

EULA and the license set forth therein,

does not require or permit, among other

things, that Keysight: (1) Furnish

technical information related to

commercial computer software or

commercial computer software

documentation that is not customarily

provided to the public; or (2) Relinquish

to, or otherwise provide, the

government rights in excess of these

rights customarily provided to the

public to use, modify, reproduce,

release, perform, display, or disclose

commercial computer software or

commercial computer software

documentation. No additional

government requirements beyond

those set forth in the EULA shall apply,

except to the extent that those terms,

rights, or licenses are explicitly required

from all providers of commercial

computer software pursuant to the FAR

and the DFARS and are set forth

specifically in writing elsewhere in the

EULA. Keysight shall be under no

obligation to update, revise or otherwise

modify the Software. With respect to

any technical data as defined by FAR

2.101, pursuant to FAR 12.211 and

27.404.2 and DFARS 227.7102, the U.S.

government acquires no greater than

Limited Rights as defined in FAR 27.401

or DFAR 227.7103-5 (c), as applicable in

any technical data.

Safety Notices

A CAUTION notice denotes a hazard. It

calls attention to an operating

procedure, practice, or the like that, if

not correctly performed or adhered to,

could result in damage to the product

or loss of important data. Do not

proceed beyond a CAUTION notice until

the indicated conditions are fully

understood and met.

A WARNING notice denotes a hazard. It

calls attention to an operating

procedure, practice, or the like that, if

not correctly performed or adhered to,

could result in personal injury or death.

Do not proceed beyond a WARNING

notice until the indicated conditions are

fully understood and met.

iii

Contents

1 Overview 1

2 Review Safety Requirements 3

2. 1 Warning Statements and Symbols 3

2. 2 Safety 4

2. 3 Weight and Dimensions 6

2. 4 Handling and Lifting 6

2. 5 Cleaning 7

2. 6 Environmental Conditions (Operating) 8

2. 7 Ventilation 9

2. 8 Location and Mounting 10

2. 9 Power Requirements 11

2. 10 Battery Replacement on the M9037A Controller 14

2. 11 AC Power Cord 15

2. 12 Protecting Against Electrostatic Discharge (ESD) 16

2. 13 Front and Rear Panel Symbols 17

2. 14 Returning for Service 19

3 Review Hardware 21

3. 1 Hardware Components 22

3. 2 Connector Descriptions 23

3. 2. 1 Connectors, 10 MHz Ref In/Out on the RuggedFrontPanel 23

3. 2. 2 Connectors, S9106AC-2IF ontheRuggedFrontPanel 24

3. 2. 3 Connectors, S9106AC-4UP ontheRuggedFrontPanel 25

3. 2. 4 Connectors, M9037APXIe EmbeddedController 26

3. 2. 5 Connectors, S9106AC-2IF and S9106AC-4UP Rear Panel 28

3. 2. 6 Connectors, E7770A CommonInterfaceUnit(CIU) fortheS9106AC-2IF

5GFR1Multi-portTransceiver 30

3. 2. 6. 1 Connectors, E7770A-LA2CIULOCard 30

3. 2. 6. 2 Connectors, E7770A-LD2CIULODistributionCard 31

3. 2. 6. 3 Connectors, E7770A-HB2CIU ChannelCard, 7to15GHzHighIF 32

3. 2. 6. 4 Connectors, E7770ACIU Rear Panel 33

3. 2. 6. 5 Connectors, E7770ACIU Rear Panel, Channel Cards 33

3. 2. 6. 6 Connectors, E7770ACIU Rear Panel, Controller Card 34

4 Install Hardware 35

4. 1 Standard Configurations 35

4. 2 KeysightS9106AC-2IF 5GFR1Multi-portTransceiver 36

4. 2. 1 Connect Cables, LAN Cables, a Display, a Keyboard & Mouse 38

4. 2. 2 Connect AC Power Cords & Power On Equipment 39

4. 3 KeysightS9106AC-4UP 5GFR1Multi-portTransceiver 40

4. 3. 1 Connect a LAN Cable, a Display, a Keyboard & Mouse 41

4. 3. 2 Connect AC Power Cord & Power On Equipment 41

5 Install Software 43

6 Verify Operation 45

6. 1 Verify X-Apps Software Controls an S9106AC-2IF 46

6. 1. 1 Verify X-Apps Controls S9106AC-2IF RF Ports at 3 GHz 46

6. 1. 2 Verify X-Apps Controls S9106AC-2IF High IF Ports at 10 GHz 50

6. 2 Verify X-Apps Software Controls an S9106AC-4UP 53

6. 2. 1 Verify X-Apps Controls S9106AC-4UP RF Ports at 3 GHz 53

7 MIMO 57

1 Overview

KeysightS9106AC-2IF and S9106AC-4UP 5GFR1Multi-port TransceiverSolutions, StartupGuide 1

1 Overview

KeysightS9106AC-2IF and S9106AC-4UP 5GFR1Multi-port TransceiverSolutions

are streamlined, non-signaling measurement systems that enable automated testing

of 5G New Radio (5G NR) infrastructure equipment.

S9106AC-2IF 5GFR1Multi-portTransceiver

contains:twoTransceivers, 380MHzto6GHz,

withMIMOSubsystem and7to15GHzHighIF

S9106AC-4UP 5GFR1Multi-portTransceiver

contains:fourTransceivers, 380MHzto6GHz,

withMIMOSubsystem

In this document...

This document describes the installation process to start up and prepare the

KeysightS9106AC-2IF and S9106AC-4UP 5GFR1Multi-port TransceiverSolutions.

1. Review this Overview

2. Review Safety Requirementsonpage3

3. Review Hardwareonpage21

4. Install Hardwareonpage35

5. Install Softwareonpage43

6. Verify Operationonpage45

7. MIMOonpage57

2 KeysightS9106AC-2IF and S9106AC-4UP 5GFR1Multi-port TransceiverSolutions, StartupGuide

2 Review Safety Requirements

KeysightS9106AC-2IF and S9106AC-4UP 5GFR1Multi-port TransceiverSolutions, StartupGuide 3

2 Review Safety Requirements

Review all safety information in this section before operating any of the equipment:

Warning Statements and Symbolsonpage3

Safetyonpage4

Weight and Dimensionsonpage6

Handling and Liftingonpage6

Cleaningonpage7

Environmental Conditions (Operating)onpage8

Review Safety Requirementsonpage3

Ventilationonpage9

Location and Mountingonpage10

Power Requirementsonpage11

Battery Replacement on the M9037A Controlleronpage14

Protecting Against Electrostatic Discharge (ESD)onpage16

Front and Rear Panel Symbolsonpage17

Returning for Serviceonpage19

2. 1 Warning Statements and Symbols

The following notices are used throughout this document. Familiarize yourself with

each of the notices and their meaning before operating these products.

A CAUTION notice denotes a hazard. It calls attention to an

operating procedure, practice, or the like that, if not correctly

performed or adhered to, could result in damage to the product or

loss of important data. Do not proceed beyond a CAUTION notice

until the indicated conditions are fully understood and met.

A WARNING notice denotes a hazard. It calls attention to an

operating procedure, practice, or the like that, if not correctly

performed or adhered to, could result in personal injury or death.

Do not proceed beyond a WARNING notice until the indicated

conditions are fully understood and met.

2 Review Safety Requirements

2. 2 Safety

The products described in this document have been designed and tested in

accordance with accepted industry standards and have been supplied in a safe

condition. This documentation contains information and warnings that must be

followed by the user to ensure safe operation and to maintain products in a safe

condition.

2. 2. 1 Safety Compliance

These products comply with the essential requirements of the European LVD (Low

Voltage Directive) as well as current editions of the following standards (dates and

editions are cited in the Declaration of Conformity):

IEC/EN 61010-1

2. 2. 2 Acoustic Statement (European Machinery Directive)

Acoustic noise emission

LpA <70 dB

Operator position

Normal operation mode per ISO 7779

4 KeysightS9106AC-2IF and S9106AC-4UP 5GFR1Multi-port TransceiverSolutions, StartupGuide

2 Review Safety Requirements

KeysightS9106AC-2IF and S9106AC-4UP 5GFR1Multi-port TransceiverSolutions, StartupGuide 5

2. 2. 3 General Safety Notices

If these products are not used as specified, the protection

provided by the equipment could be impaired.

These products must be used in a normal condition

(in which all means for protection are intact) only.

This is a Safety Protection Class I Product (provided with a

protective earthing ground incorporated in the power cord). The

Mains plug shall only be inserted in a socket outlet provided with a

protective earth contact. Any interruption of the protective

conductor inside or outside of the product is likely to make the

product dangerous. Intentional interruption is prohibited.

The KeysightS9106AC-2IF and S9106AC-4UP 5GFR1Multi-port

TransceiverSolutions are designed for use in Installation

Category II and Pollution Degree 2, per IEC 61010 Second Edition

and 664 respectively.

The KeysightS9106AC-2IF and S9106AC-4UP 5GFR1Multi-port

TransceiverSolutions are designed for indoor use only and does

not support hot-swapping of modules; for example, inserting and

removing modules with the chassis powered up. Before installing

modules in or removing modules from the chassis, power down

the chassis, but leave the power cord connected to the AC Mains

because it serves as a ground and helps protect the chassis and

modules from electrostatic damage.

2 Review Safety Requirements

2. 3 Weight and Dimensions

S9106AC BaseSystem (a PXIechassis withmodules, ruggedpanel, andcables):

Height: 192.4 mm (7.6 in); with feet removed

Height: 197.8 mm (7.8 in); with feet installed

Width: 449.5 mm (17.7 in); with rugged panel

Depth: 568.9 mm (22.4 in); with rugged panel

Weight: 24.3 kg (53.6 lbs); maximum (option dependent)

E7770A CommonInterfaceUnit(CIU):

Height: 145.6 mm ( 5.7 in); with feet installed

Width: 449 mm ( 17.7 in); across handles

Depth: 424 mm ( 16.7 in); across front connectors and rear feet

Weight: 18.1 kg (40 lbs)

2. 4 Handling and Lifting

Use both side handles when lifting the S9106AC BaseSystem or

E7770A CommonInterfaceUnit(CIU).

Use a rolling cart when transporting the S9106AC BaseSystem or

E7770A CommonInterfaceUnit(CIU).

6 KeysightS9106AC-2IF and S9106AC-4UP 5GFR1Multi-port TransceiverSolutions, StartupGuide

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Keysight Technologies

Keysight Technologies

Keysight Technologies E4980A Manual del operador

Keysight Technologies

Keysight Technologies U9361F Manual de usuario

Keysight Technologies

Keysight Technologies M981 AS Series Manual de usuario

Keysight Technologies

Keysight Technologies M9203A Guía rápida

Keysight Technologies

Keysight Technologies BT2152A Manual de servicio

Keysight Technologies

Keysight Technologies N5221/2A Series Manual de usuario

Keysight Technologies

Keysight Technologies i7090 Manual de usuario

Keysight Technologies

Keysight Technologies 16197A Manual de operación

Keysight Technologies

Keysight Technologies N778 C Series Instrucciones de funcionamiento

Keysight Technologies

Keysight Technologies P Series Manual de usuario

Keysight Technologies

Keysight Technologies E5072A Manual de usuario

Keysight Technologies

Keysight Technologies N5244BU-679 Manual de usuario

Keysight Technologies

Keysight Technologies N9020B Manual de instalación y operación

Keysight Technologies

Keysight Technologies P50 B Series Manual de usuario

Keysight Technologies

Keysight Technologies N9020A Manual de instalación y operación

Keysight Technologies

Keysight Technologies N9030B Manual de usuario

Keysight Technologies

Keysight Technologies PXA N9030A Manual de usuario

Keysight Technologies

Keysight Technologies E8740A Manual de operación

Keysight Technologies

Keysight Technologies P5000A Series Manual de usuario

Keysight Technologies

Keysight Technologies P Series Manual de usuario

Keysight Technologies

Keysight Technologies M9602A Manual de usuario

Keysight Technologies

Keysight Technologies UXA Manual de instalación y operación

Keysight Technologies

Keysight Technologies N9000A Manual de instalación y operación

Keysight Technologies

Keysight Technologies EXA Manual de instalación y operación

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario