Keysight Technologies MY53280000 Guía de inicio rápido
Option HL6, External Mixing Upgrade Kit,
Serial Prefix ≥MY/SG/US5328 to <MY/SG/US5606
Keysight Technologies
MXA Signal Analyzer
Installation Note
Notices
© Copyright 2014-2018 Keysight Technologies, Inc.
The information contained in this document is subject to change without notice.
Keysight Technologies makes no warranty of any kind with regard to this material, including but
not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Keysight Technologies shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Manual Part Number
N9020-90230
Edition
Edition 2, September 2018
Supersedes Edition 1, September 2018
Printed in USA/Malaysia
Published by:
Keysight Technologies, Inc.
1400 Fountaingrove Parkway
Santa Rosa, CA 95403
Installation Note N9020-90230 3
Option HL6, External Mixing Upgrade Kit, Serial Prefix ≥MY/SG/US5328
Option HL6, External Mixing Upgrade Kit,
Serial Prefix ≥MY/SG/US5328
Introduction
This installation note explains how to install the hardware and provides guidelines for adjustment
and verification for Option HL6, External Mixing Upgrade for MXA signal analyzers with serial
number prefixes from MY/SG/US5328 to <MY/SG/US5606. A similar kit, Option EXM, is available
for MXA signal analyzers serial number prefix = MY/SG/US5233 and ≥MY/SG/US5606. There is no
external mixing upgrade available for MXA signal analyzers with serial number prefix
< MY/SG/US5233.
The A13 Front End Assembly that was originally installed in MXAs with serial number prefixes listed
in the box above does not support External Mixing. Therefore, a new A13 Front End Assembly is also
included in the kit, along with the necessary license, cables and connectors required for External
Mixing.
Depending upon what other options are already installed, the A15 Front End Controller board
currently installed in the MXA may also need to be replaced with the Enhanced Front End Controller
(EFEC) board included in this kit. To allow the necessary adjustments the EFEC requires, a license
for Option CR3, 2nd IF Output is also included.
Software and test equipment is required for making adjustments and for performance verification
testing. Information on how to obtain this software can be found at:
www.keysight.com/find/calibrationsoftware
Products Affected: N9020A, MXA Signal Analyzer
Serial Numbers: ≥ MY53280000 to <MY56060000
≥ SG53280000 to <SG56060000
≥ US53280000 to <US56060000
To Be Performed By: (X) Keysight Service Center
(X) Personnel Qualified by Keysight
( ) Customer
Estimated Installation Time:
Estimated Adjustment Time:
Estimated Verification Time:
2.0 Hours
4.0 Hours
4.0 Hours
Instrument software revision A.14.00 or later is required to install this upgrade.
The instrument must be readjusted and the performance tested to assure the instrument meets
specifications following the hardware installation. The X-Series Performance Verification and
Adjustment Software must be used and have revision E.11.04 or later. All adjustments are
automated. This software is included in the N7814A, Keysight X-Series Signal Analyzer
Calibration Application software.
4Installation Note N9020-90230
Option HL6, External Mixing Upgrade Kit, Serial Prefix ≥MY/SG/US5328
Installation Kit Parts List
Quantity Description Keysight Part
Number
1 A13 Front End Assembly N9020-60314
1 A15 Front End Controller w/ IF MUX N9020-60172
1 Adapter-Coaxial Straight Female-SMA to Female-SMA, 50 Ω1250-1666
1 Washer, Lock, Internal Tooth, ¼-inch 2190-0067
1 Nut-Hex-Double-Chamfer ¼-36-THD .125-IN-THK Stainless Steel 2950-0223
150ΩTermination, SMA male 1810-0118
1 Cable Assembly, External Mixing, Front Panel (W27) N9020-20166
1CableAssembly,μW Front End to W27 (W28) N9020-20241
1 Opt EXM/HL6 Cable Kit with Wire Markers
(includes W26, W36, W37, and W39, listed below)
N9020-60212
1 Cable Assembly, Coaxial 350 mm LG (W26) 8121-2027awith ends
labeled ‘903’ and ‘13’
a. This cable is included in the Opt EXM/HL6 Cable Kit with Wire Markers, p/n N9020-60212.
1 Cable Assembly, Coaxial 240 mm LG (W36) 8121-1862awith ends
labeled ‘902’ and ‘7’
1 Cable Assembly, Coaxial 530 mm LG (W37) 8121-1401awith ends
labeled ‘900’ and ‘100’
1 Cable Assembly, Coaxial 525 mm LG (W39) 8121-2028awith one
end labeled ‘1100’
1 Label, Warning N9030-80018
5 Cable Ties 1400-0249
1 Entitlement Certificate 5964-5178
1 Entitlement Certificate Envelope 5967-7169
1 Installation Note This note
Installation Note N9020-90230 5
Option HL6, External Mixing Upgrade Kit, Serial Prefix ≥MY/SG/US5328
Tools Required
— T-10 TORX Driver
— T-20 TORX Driver
— 5/16-inch torque wrench
— ¼-inch open-end wrench
— 9/16-inch nut driver
— ¼-inch socket on 4-pound torque wrench
— Scissors or knife
—Diagonalcutters
— Keysight Calibration and Adjustment Software, N7814A (revision E.11.04 or later)
— Test equipment and computer supported by the X- Series Performance Tests and Adjustment
Software
— MXA Signal Analyzer Service Guide. This manual is available as:
— N9020A Option OBW or
— Keysight part number N9020-90218
— Microsoft Windows based personal computer with internet access and USB port
— USB storage device with > 2 GB free memory
Initial Instrument Functionality Check
Power on the instrument and allow the instrument to boot up. Run an alignment and display the
measurement screen. (The instrument will probably display a spectrum analyzer screen and you will
see the instrument sweeping.)
There should be no alignment failures. If there are failures, investigate and fix the problem before
continuing.
Before you disassemble the instrument, turn the power switch to Standby. After the instrument
has completely shut down, unplug the instrument. Failure to unplug the instrument can result in
personal injury.
Electrostatic discharge (ESD) can damage or destroy electronic components. All work on
electronic assemblies should be performed at a static-safe workstation. Refer to the
documentation that pertains to your instrument for information about static-safe workstations
and ordering static-safe accessories.
6Installation Note N9020-90230
Option HL6, External Mixing Upgrade Kit, Serial Prefix ≥MY/SG/US5328
Installation Procedure
Analyzer Information
1. Connect a power cord to the analyzer and turn on the analyzer.
2. After the analyzer has completed turning on, press System, Show, System. Make note of the
following information from the Show System screen:
Product Number: _____________
Serial Number: ______________
Instrument S/W Revision: ______________
3. Check for the presence of one of the following options listed below in the Show System. Put a
check mark or “X” after the option listed below that appears in the Show System menu.
N9020A-B40_____
N9020A-CR3_____
N9020A-CRP_____
N9020A-DP2_____
N9020A-MPB_____
N9020A-BBA_____
4. On the analyzer, press System, Show, Hardware. Note the Part #, Matl Rev, Rev, OF Rev, and
Hw Id of the Front End Controller and Front End in the table below.
5. Refer to the data in step 2 above. If the Product Number is not N9020A, do not proceed with
the installation of this kit. This kit is to be installed only on N9020A signal analyzers.
6. Refer to the data in step 2 above. If the Serial Number prefix (the first six characters of the
serial number) is earlier than MY5328, SG5328, or US5328, or is later than MY/SG/US5606 do
not proceed with the installation of this kit. This kit is to be installed only on N9020A signal
analyzers with serial prefixes from ≥MY/SG/US5328 to <MY/SG/US5606.
7. Refer to the data in step 3 above. If option N9020A-BBA is present, there will be additional
steps required to remove and replace the front panel assembly.
8. Refer to the data in step 3 above. If option N9020A-B40, N9020A-MPB and/or N9020A-DP2 is
already present, the EFEC is already installed and you do not need to perform the Replace
Front End Controller procedure.
Assembly Name Part # Matl Rev Rev OF Rev Hw Id
Front End Controller
Front End
Installation Note N9020-90230 7
Option HL6, External Mixing Upgrade Kit, Serial Prefix ≥MY/SG/US5328
9. Refer to the data in step 4 above. Verify that the Front End assembly has a HW ID of 70.
10.Refer to the data in step 3 and step 4 above. If the analyzer has N9020A-CR3 and/or
N9020A-CRP installed, verify that it also has a Front End Controller with Hw Id of 75. If the
Front End Controller has a Hw Id of 75, you do not need to perform the Replace Front End
Controller procedure.
Update Instrument Software
Updating the instrument software and installing the necessary licenses before installing the new
hardware will help ensure that the hardware installation was successful.
Go to the following website and determine whether or not the analyzer has the latest instrument
software already installed:
http://www.keysight.com/find/xseries_software
If the analyzer does not have the latest instrument software already installed, download and install
the latest version.
8Installation Note N9020-90230
Option HL6, External Mixing Upgrade Kit, Serial Prefix ≥MY/SG/US5328
Licensing the New Options
1. Locate the Option Upgrade Entitlement Certificate (5964-5178) from the kit.
2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the
Certificate.
3. After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an
attached License File.
4. Locate a USB storage device. Perform a virus scan on this device before use.
5. Save the License File to the root directory of the USB Storage Device.
6. Connect the USB Storage Device to one of the analyzer’s USB ports. Connect a mouse to
another USB port. Windows will detect the new hardware and may display the configuration
menu shown in Figure 1. This menu may be configured according to your preferences.
Figure 1 USB Storage Device Configuration Menu
Installation Note N9020-90230 9
Option HL6, External Mixing Upgrade Kit, Serial Prefix ≥MY/SG/US5328
7. The signal analyzer will automatically consume the License File. (This may take a few minutes)
When the License File is consumed the Keysight License Manager will display a “Successful
License Installation” message as shown in Figure 2. Since the license file contains multiple
licenses, multiple “Successful License Installation” messages will appear. Wait until all
licenses have been consumed before removing the USB Storage Device.
Figure 2 Successful License Installation
Verify the License Installation
1. Before the licenses will be recognized, the XSA application must be restarted. Press File, Exit.
An Exit Analyzer dialog box will appear; press Enter to confirm the exit.
2. Double-click on the LaunchXSA icon on the Windows desktop. Wait for the XSA application to
finish starting (the analyzer should be sweeping).
3. Press System, Show, System on the analyzer to display a list of all displayed options. You
should see the following options listed:
—N9020A-EXM External Mixing
—N9020A-CR3 Connector Rear, 2nd IF Output
—N9060A-3FP Amplitude Correction and Limit Lines
—N9060A-4FP TOI and Harmonics
—N9060A-5FP ACP 18 Carrier Measurement
—N9060A-6FP TV Trigger and IQ Analyzer Enhancement
—N9060A-7FP Zero Span, Register, Trace, and Spurious Enhancements
10 Installation Note N9020-90230
Option HL6, External Mixing Upgrade Kit, Serial Prefix ≥MY/SG/US5328
Analyzer Disassembly
If the instrument is placed on its face during any of the following procedures, be sure to use a soft
surface or soft cloth to avoid damage to the front panel, keys, or input connector.
If the analyzer has Option PRC, Portable Configuration, refer to the “Portable Instrument
(Option PRC)” section on page 12 to remove the outer case.
Make sure any adapters on the front panel are removed.
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Instrumento de medición de Keysight Technologies
Keysight Technologies
Keysight Technologies N5244/5B Manual de usuario
Keysight Technologies
Keysight Technologies U4205A Manual de usuario
Keysight Technologies
Keysight Technologies N9000B Manual de instalación y operación
Keysight Technologies
Keysight Technologies B2901A Manual de usuario
Keysight Technologies
Keysight Technologies N9340B Manual de usuario
Keysight Technologies
Keysight Technologies PXA N9030A Manual de usuario
Keysight Technologies
Keysight Technologies E5061B Manual de usuario
Keysight Technologies
Keysight Technologies X Series Manual de usuario
Keysight Technologies
Keysight Technologies N9000A Manual de instalación y operación
Keysight Technologies
Keysight Technologies U2020 X Series Manual de usuario
Keysight Technologies
Keysight Technologies EPM Series Manual de usuario
Keysight Technologies
Keysight Technologies EXA N9010A Manual de usuario
Keysight Technologies
Keysight Technologies M9391A PXIe Guía del usuario
Keysight Technologies
Keysight Technologies InfiniiMax III Series Manual de usuario
Keysight Technologies
Keysight Technologies N5224/5A Manual de usuario
Keysight Technologies
Keysight Technologies N5245-60106 Manual de instalación y operación
Keysight Technologies
Keysight Technologies M9370A Manual de usuario
Keysight Technologies
Keysight Technologies B2900B Series Manual de usuario
Keysight Technologies
Keysight Technologies E5061B ENA Series Manual de usuario
Keysight Technologies
Keysight Technologies U2000 Series Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario