Keysight Technologies FieldFox N9913A Manual de usuario

Keysight Technologies

FieldFox Handheld Analyzers

4/6.5/9/14/18/26.5/32/44/50 GHz

Configuration

Guide

02 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

Table of Contents

The FieldFox Handheld Analyzer Family 03

FieldFox RF and Microwave (Combination) Analyzers 04

FieldFox RF and Microwave (Combination) Analyzer FAQs 05

FAQs – Applicable To All FieldFox RF and Microwave Analyzers 08

FieldFox Microwave Vector Network Analyzers 10

FieldFox Microwave Vector Network Analyzer FAQs 11

FieldFox Microwave Spectrum Analyzers 12

FieldFox Spectrum Analyzer FAQs 13

Documentation 13

Upgrades 14

Calibration Kits 16

Accessories 18

03 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

RF and microwave

(combination) analyzer

Microwave vector

network analyzer (VNA)

Microwave spectrum

analyzer (SA)

Option Description N991xA

N995xA

N992xA N993xA

N996xA

CAT/vector network analysis

010 VNA time domain √ √ —

112 QuickCal √ on N991xA

- on N995xA √—

210 VNA transmission/reflection √Base model —

211 VNA full 2-port S-parameters √√—

212 1-port mixed-mode S-parameters √ √ —

215 TDR cable measurements √ √ —

305 Cable and antenna analyzer Base model √Note 1

308 Vector voltmeter √ √ —

320 Reflection meas. (RL, VSWR and scalar meas.) Note 2 Note 2 √

Spectrum analysis

209 Extended range transmission analysis (ERTA) √ —√

220 Tracking generator Note 3 — √

233 Spectrum analyzer √—Base model

235 Pre-amplifier √—√

236 Interference analyzer and spectrogram √ —√

238 Spectrum analyzer time gating √ —√

312 Channel scanner √—√

350 Real-time spectrum analyzer (RTSA) √ - on N9912A —√

351 I/Q Analyzer (IQA) √ - on N9912A —√

355 Analog demodulation √ —√

Power measurements

208 USB power sensor meas. versus frequency √ √ √

302 USB power sensor support √ √ √

310 Built-in power meter √ √ √

330 Pulse meas. with USB peak power sensor √ √ √

System features

030 Remote control capability √ √ √

307 GPS receiver √ √ √

309 DC bias variable-voltage source √ √ √

Windows based software

89601B 89600 VSA Software √ - on N9912A —√

Notes:

Base model means that the functionality listed is the primary function of that instrument. For example, on the N991xA or N995xA combo analyzers,

cable and antenna analysis is the standard function included with every N991xA or N995xA.

1. Option 305 is not available on the N993xA or N996xA. However, a subset of cable and antenna analyzer measurements, return loss and VSWR, is available

as Option 320.

2. Option 320 is not applicable to N991xA, N995xA, or N992xA. The reflection measurements of return loss and VSWR are included with every N991xA,

N995xA, and N992xA. So there is no need for an Option 320 on these analyzers.

3. On the N991xA or N995xA analyzers, order Options 233 and 210 to obtain a tracking generator with the spectrum analyzer. There is no Option 220 on the

N991xA or N995xA analyzers. To obtain tracking generator capability, you need Options 233 and 210. Option 233 provides the spectrum analyzer capability

and Option 210 the “tracking” capability.

The FieldFox Handheld Analyzer Family

This configuration guide describes configurations, options and accessories for the FieldFox family of portable analyzers. This guide

should be used in conjunction with the technical overview and data sheet for a complete description of the analyzers. The table below

shows a comparison of the functions available in the FieldFox family of analyzers.

The following accessories are included with every FieldFox: AC/DC adapter, battery, soft carrying case, LAN cable and Quick Reference

Guide.

Note: Combination analyzer (combo) = Cable and antenna tester (CAT) + Vector network analyzer (VNA) + Spectrum analyzer (SA)

FieldFox family and options

04 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

FieldFox RF and Microwave (Combination) Analyzers

FeldFox RF and microwave (combination) analyzer models

Step 1. Select the model that provides the desired frequency range.

Model Description CAT and VNA frequency SA frequency 1Test port connectors

N9913A 4 GHz FieldFox RF analyzer 30 kHz to 4 GHz 100 kHz to 4 GHz Type-N (f)

N9914A 6.5 GHz FieldFox RF analyzer 30 kHz to 6.5 GHz 100 kHz to 6.5 GHz Type-N (f)

N9915A 9 GHz FieldFox microwave analyzer 30 kHz to 9 GHz 100 kHz to 9 GHz Type-N (f)

N9916A 14 GHz FieldFox microwave analyzer 30 kHz to 14 GHz 100 kHz to 14 GHz Type-N (f)

N9917A 18 GHz FieldFox microwave analyzer 30 kHz to 18 GHz 100 kHz to 18 GHz Type-N (f)

N9918A 26.5 GHz FieldFox microwave analyzer 30 kHz to 26.5 GHz 100 kHz to 26.5 GHz 3.5 mm (m)

N9950A 32 GHz FieldFox microwave analyzer 300 kHz to 32 GHz 9 kHz to 32 GHz NMD 2.4 mm (m)

N9951A 44 GHz FieldFox microwave analyzer 300 kHz to 44 GHz 9 kHz to 44 GHz NMD 2.4 mm (m)

N9952A 50 GHz FieldFox microwave analyzer 300 kHz to 50 GHz 9 kHz to 50 GHz NMD 2.4 mm (m)

Step 2. Select optional measurement capabilities.

Any of these options can easily be added as a software upgrade in the future.

Exception: Option 112 is only applicable to N991xA models. It is not applicable to N995xA models.

FieldFox RF and microwave (combination) analyzer options

Option Description Prerequisite options/notes

CAT/vector network analysis

010 VNA time domain Requires 210, recommend 211

112 QuickCal Not available for N995xA models. See page 5, FAQ #9

210 VNA transmission/reflection Recommend ordering a cal kit

211 VNA full 2-port S-parameters Requires 210, recommend ordering a cal kit

212 1-port mixed-mode S-parameters Requires 210 and 211

215 TDR cable measurements -

308 Vector voltmeter 210 and 211 required to obtain full VVM functionality. See page 5, FAQ #8

Spectrum analysis

209 Extended range transmission analysis (ERTA) Requires 233 and 210. Recommend 307. Requires two FieldFoxes. See page 6, FAQ # 10.

233 Spectrum analyzer -

235 Pre-amplifier Requires 233

236 Interference analyzer and spectrogram Requires 233

238 Spectrum analyzer time gating Requires 233

312 Channel scanner Requires 233

350 Real-time spectrum analyzer (RTSA)3Requires 233, Recommend 235.

351 I/Q Analyzer (IQA)3Requires 233

355 Analog demodulation Requires 233

Power measurements

208 USB power sensor meas. versus frequency Requires 302

302 USB power sensor support Need to order USB power sensor 2

310 Built-in power meter No power sensor required. See page 8, FAQ #1

330 Pulse meas. with USB peak power sensor Need to order USB peak power sensor. See page 9, FAQs #7 and #8

System features

030 Remote control capability Requires an iOS device

307 GPS receiver Need to order GPS antenna, N9910X-825. See page 9, FAQ #3

309 DC bias variable-voltage source -

Windows based software

89601B 89600 VSA Software3Requires 233

1. Usable to 5 kHz

2. List of compatible sensors available from www.keysight.com/find/fieldfoxsupport

3. Requires CPU2 fast processor. See page 6, FAQ #13

05 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

Question Answer

1. What is included with a base

N991xA/N995xA analyzer?

–The base model includes the cable and antenna analyzer

–Measurements: DTF (dB, linear, VSWR), return loss and DTF, return loss (dB), and 1-port cable loss

–Calibrations: CalReady, OSL, and response cal

Note: 2-port insertion loss is NOT included with the base model, if 2-port insertion loss is needed, order Option 210

Note: There is no phase information with the base analyzer, to obtain S11 or S21 phase, order Option 210

2. What is included with N991xA/

N995xA Option 233?

–Basic spectrum analysis, four traces, different detector types, radio standard selection, limit lines

–Channel power, occupied bandwidth, adjacent channel power

–AM/FM tune and listen, field strength measurements, antenna factors, frequency counter marker

–Tracking generator (TG)/Independent source:

–TG CW mode (source CW frequency can be set independent of SA frequency) - included

–TG CW coupled mode (source CW frequency is autocoupled to SA’s center frequency) - included

–TG tracking mode (traditional TG operation, swept SA coupled to swept source) - (requires Option 210)

3. What is included with N991xA/

N995xA Option 236?

–Interference analyzer and spectrogram

–Trace playback and recording

4. What is included with N991xA/

N995xA Option 210?

–Option 210 adds a VNA with transmission/reflection (T/R) capability

–Measurements: S21, S11, magnitude and phase

–Additionally, in the CAT mode, you can measure 2-port insertion loss

–Calibrations: CalReady, OSL, response, and enhanced response cal

–If you need all four S-parameters, order Options 210 and 211

–If you need 2-port cal, order Options 210 and 211

–Adds tracking mode to the tracking generator/independent source included with Option 233, spectrum

analyzer

5. What is included with N991xA/

N995xA Option 211?

–Option 211 adds full 2-port S-parameter capability to the VNA mode

–Measurements: All four S-parameters (S11, S21, S22, S12), magnitude and phase

–Calibrations: CalReady, OSL, response, enhanced response, and full 2-port cal

6. Can I measure group delay on

N991xA/N995xA analyzers?

If you have phase measurement capability, then you can measure group delay. Option 210 is required for any phase

measurement capability. So if you do not have Option 210, you cannot measure group delay.

7. What is included with N991xA/

N995xA Option 010?

–S11/S21 in time domain, if Option 210 is ordered. To get time domain data for all four S-parameters and full

2-port cal, order Option 211.

–View both time and frequency domain data at the same time

–Low-pass, impulse, and band-pass modes

–Minimum, medium, and maximum window

–Gating

8. What is included with N991xA/

N995xA Option 308?

–With Option 308: 1-port cable trimming

–With Options 308 and 210: 1-port cable trimming, 2-port transmission

–With Options 308, 210, and 211: 1-port cable trimming, 2-port transmission, A/B and B/A

Note: A/B and B/A measurements require an external source

9. What is included with N991xA

Option 112?

–Option 112 (QuickCal), is not available for N995xA analyzers. It is available for N991xA analyzers.

–QuickCal is included with Option 112.

–1-port QuickCal with a base analyzer.

–1-port and enhanced response QuickCal with a T/R analyzer (one that has Option 210).

–1-port, enhanced response, and 2-port QuickCal with a full 2-port analyzer (one that has Option 211).

–QuickCal is most accurate for DUTs with 7/16 and Type-N connectors and measurement uncertainties are

provided for frequencies ≤ 18 GHz. Reduced accuracy for DUTs with 3.5 mm (m), SMA (m), or other male

coaxial connectors; performance is unspecified. QuickCal is not recommended for DUTs with 3.5 mm (f), SMA

(f), or other similar female connectors. QuickCal is not applicable to waveguide.

FieldFox RF and Microwave (Combination) Analyzer FAQs

06 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

FieldFox RF and Microwave (Combination) Analyzer FAQs (continued)

Question Answer

10. What are the requirements for

Option 209?

Extended Range Transmission Analysis (ERTA) or Option 209 is a scalar measurement system based on the use of

two FieldFoxes. One FieldFox acts as the source and reference receiver, while the second FieldFox acts as the

measurement receiver. When different frequency models are used in an ERTA pair, the ERTA system frequency

range is limited to the lowest of the pair.

Required hardware

A. Two FieldFoxes. FieldFoxes can be any of these models:

–FieldFox microwave combination analyzers: N9913A, N9914A, N9915A, N9916A, N9917A, N9918A, N9950A,

N9951A, N9952A

–FieldFox microwave spectrum analyzers: N9935A, N9936A, N9937A, N9938A, N9960A, N9961A, N9962A

–ERTA cannot use N9912A, N9923A, N9925A, N9926A, N9927A or N9928A

The two FieldFoxes used in ERTA do not have to be the same model.

ERTA requires the following options on Combo FieldFoxes.

(N9913A, N9914A, N9915A, N9916A, N9917A, N9918A, N9950A, N9951A, N9952A)

–Option 210, VNA transmission/reflection

–Option 233, spectrum analyzer

ERTA requires the following options on SA FieldFoxes.

(N9935A, N9936A, N9937A, N9938A, N9960A, N9961A, N9962A)

–Option 220, tracking generator

Both FieldFoxes (the one used as the source, and the other used as the receiver) must have the options listed

above. The ERTA option (209) cannot be installed unless 210 and 233 are present on a combo analyzer, or 220 is

present on an SA analyzer.

With either the Combo or SA FieldFoxes, the following options are highly recommended:

–Option 235, preamplifier – this option increases the measurement dynamic range by increasing the received

signal power.

–Option 307, GPS receiver – this option increases the dynamic range by increasing the frequency accuracy

and permitting the use of a narrower RBW.

B. Power splitter, two-resistor model, Keysight 11667A, 11667B, or 11667C. Other power splitters can be used but the

specifications listed are based on the match and tracking performance of 11667A, 11667B, or 11667C. Three-resist-

er power splitters are not recommended.

C. N9910X-712, Trigger/Reference-in cable, SMA (m) to BNC(f), 1 m, quantity two

D. N9910X-713, Trigger/Reference-out cable, SMB (m) to BNC (m), 1 m, quantity two

E. LAN connection – For ERTA, the two FieldFoxes communicate via a LAN connection. For a direct connection, a

cross-over LAN cable is required. Alternately, both analyzers can be on a local area network.

Recommended accessory

F. N9910X-825, GPS Antenna

11. What is included with

Option 355?

FieldFox analog demodulation has two parts: (1) Tune and listen, and (2) AM/FM metrics. Tune and listen is available

with the purchase of the spectrum analyzer option 233. AM/FM metrics becomes available when Option 355 is

purchased. AM/FM metrics provides the user with RF spectrum view, demodulated baseband signal waveform,

carrier power, frequency deviation, SINAD and more.

12. What is included with

Option 350?

Real-time spectrum analyzer (RTSA) or Option 350 provides real-time measurements on a FieldFox. The FieldFox

must be equipped with spectrum analysis capability. The preamplifier option is recommended, as elusive signals

often have low power levels. The maximum real-time bandwidth for option 350 is 10 MHz. RTSA includes trace

recording and playback capabilities. It does not include a frequency-mask trigger (FMT).

13. How do I determine if my

FieldFox has CPU2 fast

processor?

All N995xA and N996xA analyzers include CPU2. On other FieldFox models, if the serial number starts with

MY5607/SG5607/US5607, then it has CPU2. If the serial number prefix is different, then the analyzer firmware

needs to be checked to see if the instrument has been upgraded with N9910HU-100/200/300/400 to have CPU2.

07 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

FieldFox RF and Microwave (Combination) Analyzer FAQs (continued)

Question Answer

14. Is Spectrum Analyzer Trace

Recording and Playback

standard or an option?

–Spectrum Analyzer mode (Option 233) does not include Trace Recording and Playback by default. To obtain

this capability in SA mode, Option 236 Interference Analyzer and Spectrogram needs to be purchased.

–RTSA mode (Option 350) does include Trace Recording and Playback by default in RTSA mode.

–Purchasing RTSA mode (Option 350) does not enable Trace Recording and Playback in SA mode (Option 233).

Trace record/playback features

SA mode

SA & Interference Analyzer

Options 233 and 236

RTSA mode

RTSA

Option 350

Record and playback spectrum traces Yes Yes

Save trace data with GPS time stamp over time Yes Yes

Record and playback spectrogram data Yes No*

Frequency mask trigger Yes No

* RTSA trace recordings can be recalled and played back in SA mode Spectrogram. This has the added benefit that the

measurements are shown ‘slower’, making it easier for the human eye to decipher the signal content.

Item Description/Options Quantity

FieldFox Combo analyzer: required Option 210, 233. Recommended: 235, 307

SA analyzer: required: Option 220, recommended: 235, 307

Power splitter 11667A (Type-N) or 11667B (3.5 mm) or 11667C (2.4 mm) 1

Type-N(m) to Type-N(m) adapter N9910X-850 (for use with 11667A or Type-N systems) 1

Trigger cables1 N9910X-712, SMA(m) to BNC(f)

N9910X-713, SMB(m) to BNC(m)

2 of each

Total of 4 cables

RF test cable Connecting FieldFox source port 1 to power splitter input 1

RF test cable or adapter Connecting power splitter output arm to FieldFox port 2 1

RF jumper cable or adapter Power splitter output arm to DUT input 1

RF jumper cable or adapter DUT output to FieldFox receiver port 2 1

LAN cable LAN cable to connect FieldFoxes directly, or the analyzers must be on the LAN 1

N9910X-825 GPS antenna, recommended. Necessary if Option 307 is ordered. 2

1. The trigger cables and LAN cables must be at least as long as the separation distance between the two ends of the DUT.

ERTA System Typical Configuration

ERTA system diagram

08 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

FAQs – Applicable To All FieldFox RF and Microwave Analyzers

Question Answer

1. What USB

power sensors

work with

Option 302?

All Keysight U2000x Series USB power sensors are supported with FieldFox.

Visit: www.keysight.com/find/fieldfoxsupport for an up-to-date listing.

2. What is the

difference

between USB

power sensor

(Option 302)

and built-in

power meter

(Option 310)?

Option 302

USB power sensor

Option 310

Built-in power meter (or channel power meter)

Description Option 302 allows users to connect a

USB power sensor to FieldFox’s USB

port and make broadband power

measurements.

Option 310 is a channelized power measurement capability built

into FieldFox analyzers. Maximum bandwidth is 100 MHz.

External hardware USB power sensor required None. Uses internal receiver.

Power measurement Broadband diode detector, measures

all frequencies

Tuned receiver, so measures frequencies within defined channel

bandwidth

Frequency range Depends on USB sensor Frequency range of the analyzer

Settings Set CW frequency Set CW frequency, Set channel width/span

Power range Depends on USB sensor Depends on channel width and attenuator setting.

Warm-up time 30 minutes to meet accuracy

specifications

No warm-up time required

Accuracy Depends on USB sensor InstAlign accuracy: ± 0.5 dB typical for a CW signal. Since the

measurement is within a certain frequency channel or bandwidth,

to make an accurate measurement, the user needs to know the

exact center frequency and the signal’s bandwidth and set those

accurately.

Programmable Yes, via SCPI Yes, via SCPI

Physical connection The power sensor can easily be

moved to the measurement point,

with a USB cable connecting the

detector to FieldFox.

The measurement point needs to be connected to FieldFox’s RF

input port. If a RF jumper cable is used, the user needs to account

for the loss of the cable with an offset value (can be entered into

the analyzer).

FieldFox source control Yes, on/off, and nominal power level

control

No access to FieldFox’s source from the built-in power meter mode

09 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

FAQs – Applicable To All FieldFox RF and Microwave Analyzers (continued)

Question Answer

3. What do I need to get GPS

information?

(1) The recommended GPS solution is to order:

–Option 307 - built-in GPS receiver

–A GPS antenna such as N9910X-825

–Other GPS antennas can also be used

–The GPS connector on the instrument is SMA (f)

(2) Alternatively, you can purchase a USB-based GPS receiver. You do not need to purchase any FieldFox options

for the USB-based GPS to work. However, the USB-based GPS only provides time and location data, and time

synchronization capability. It cannot be used to increase the frequency accuracy of the instrument.

4. What is the connector for Option

309, DC output?

The DC output has a SMB (m) connector. Recommend ordering N9910X Option 713 bias-tee power cable SMB (f)

to BNC (m).

5. What are the connectors for

the Reference/Trigger In and

Reference/Trigger Out?

The connector for the Ref/Trig In is SMA (f). Recommend ordering N9910X Option 712 Trig/Ref in SMA (m) to BNC

(f) cable.

The connector for the Ref/Trig Out is SMB (m). Recommend ordering N9910X Option 713 bias-tee power cable

SMB (f) to BNC (m).

6. What is Option 030 Remote

control capability?

(1) Option 030 provides a license for FieldFox to allow remote control via an iOS device.

(2) Not supplied by user, but necessary for operation of Option 030 are:

–iOS device: iPad, iPhone, or iPod Touch with iOS 6.1 or higher with free FieldFox app

–A WiFi or 3G/4G network connection between FieldFox and iOS device

7. What USB sensor is required for

Option 330?

Option 330 or pulse measurements requires a Keysight USB peak power sensor. Visit

www.keysight.com/find/usbsensorsforfieldfox for a list of supported peak power sensors. Average power sensors

cannot be used with Option 330, only peak power sensors. The peak power sensor needs to be purchased

separately.

8. What measurement capabilities

are included with Option 330?

Average power, peak power, and peak to average ratio

Analog gauge display and digital display, dBm and watts

Relative/absolute measurements, dB or %, minimum and maximum limits

Trace graph for pulse profiling with gating

Rise time, fall time, pulse width, pulse period, pulse repetition frequency

9. What is included with Option 208? Option 302, USB power sensor measurements, includes CW power measurements (one frequency at a time). With

Option 208 added, you can make swept-frequency power measurements. You can plot source power, gain, and

receive power versus frequency. Additionally, the source frequency can be offset from the receiver frequency. The

power sensor needs to be purchased separately.

10 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

Step 1. Select the model that provides the desired frequency range.

Model Description Frequency Test port connectors

N9925A 9 GHz FieldFox microwave VNA 30 kHz to 9 GHz Type-N (f)

N9926A 14 GHz FieldFox microwave VNA 30 kHz to 14 GHz Type-N (f)

N9927A 18 GHz FieldFox microwave VNA 30 kHz to 18 GHz Type-N (f)

N9928A 26.5 GHz FieldFox microwave VNA 30 kHz to 26.5 GHz 3.5 mm (m)

A standard N992xA FieldFox microwave VNA includes transmission/reflection measurement capability. Additional functionality such as

full 2-port S-parameters can be added using the options listed below.

Step 2. Select optional measurement capabilities.

Any of these options can easily be added as a software upgrade in the future.

FieldFox microwave vector network analyzer options

FieldFox Microwave Vector Network Analyzers

FieldFox microwave vector network analyzer models

Option Description Prerequisite options/notes

Vector network analysis / CAT

010 VNA time domain Recommend 211

112 QuickCal See page 11, FAQ #7

211 VNA full 2-port S-parameters -

212 1-port mixed-mode S-parameters Requires 211

215 TDR cable measurements Requires 305

305 Cable and antenna analyzer -

308 Vector voltmeter 211 required to obtain full VVM functionality. See page 11, FAQ #5

Power measurements

208 USB power sensor meas. versus frequency Requires 302

302 USB power sensor support Need to order USB power sensor1

310 Built-in power meter No power sensor required. See page 8, FAQ #1

330 Pulse meas. with USB peak power sensor Need to order USB peak power sensor. See page 9, FAQs #7 and #8

System features

030 Remote control capability Requires an iOS device

307 GPS receiver Need to order GPS antenna, N9910X-825. See page 9, FAQ #3

309 DC bias variable-voltage source -

1. List of compatible sensors available from www.keysight.com/find/fieldfoxsupport

Otros manuales para FieldFox N9913A

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Keysight Technologies

Keysight Technologies

Keysight Technologies B1500A Guía de instalación

Keysight Technologies

Keysight Technologies UXA N9040B Manual de instalación y operación

Keysight Technologies

Keysight Technologies N9030B Guía de inicio rápido

Keysight Technologies

Keysight Technologies PNA Series Manual de usuario

Keysight Technologies

Keysight Technologies E5052B Manual del propietario

Keysight Technologies

Keysight Technologies N9340B Manual de usuario

Keysight Technologies

Keysight Technologies ENA Series Guía de inicio rápido

Keysight Technologies

Keysight Technologies 34972A Manual de usuario

Keysight Technologies

Keysight Technologies N5244/5B Manual de usuario

Keysight Technologies

Keysight Technologies N2797A Manual de usuario

Keysight Technologies

Keysight Technologies M9203A Guía rápida

Keysight Technologies

Keysight Technologies B2901A Manual de usuario

Keysight Technologies

Keysight Technologies U1733C Manual de usuario

Keysight Technologies

Keysight Technologies N5222B Guía de inicio rápido

Keysight Technologies

Keysight Technologies N9340B Manual de usuario

Keysight Technologies

Keysight Technologies N9000A Manual de instalación y operación

Keysight Technologies

Keysight Technologies P Series Instrucciones de funcionamiento

Keysight Technologies

Keysight Technologies BT2152B Manual de servicio

Keysight Technologies

Keysight Technologies B1500A Manual de instrucciones

Keysight Technologies

Keysight Technologies 16197A Manual de operación

Keysight Technologies

Keysight Technologies X Series Manual de usuario

Keysight Technologies

Keysight Technologies B1500A Manual de usuario

Keysight Technologies

Keysight Technologies LTE Manual de instalación

Keysight Technologies

Keysight Technologies C Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario