Keysight Technologies N9030B Guía de inicio rápido
Option B85, 25 MHz to 85 MHz Analysis Bandwidth Upgrade
Option B1X, 25 MHz to 160 MHz Analysis Bandwidth Upgrade
Option BU3, 40 MHz to 160 MHz Analysis Bandwidth Upgrade
Keysight Technologies
N9030B PXA Signal Analyzer
Installation Note
Notices
© Copyright 2016 Keysight Technologies, Inc.
The information contained in this document is subject to change without notice.
Keysight Technologies makes no warranty of any kind with regard to this material, including but
not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Keysight Technologies shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Manual Part Number
N9030-90075
Edition
Edition 1, March 2016
Printed in USA/Malaysia
Published by:
Keysight Technologies, Inc.
1400 Fountaingrove Parkway
Santa Rosa, CA 95403
Installation Note N9030-90075 3
Option B85 or B1X Retrofit Kit
Option B85 or B1X Retrofit Kit
Introduction
This installation note explains how to install the hardware and provides guidelines for adjustment
and verification for the following upgrade kits for N9030B PXA signal analyzers:
— Option B85, Analysis Bandwidth Upgrade, 25 MHz, or 40MHz, to 85 MHz, Hardware and
License
— Option B1X, Analysis Bandwidth Upgrade, 25 MHz to 160 MHz, Hardware and License
— Option BU3, is the ordering number for the retrofit kit that installs option B1X on instruments
with option B40 previously installed.
Refer to http://www.keysight.com/find/pxa_upgrades for information on all available upgrades
In addition to installing the licenses and hardware to support options B85, or B1X, as appropriate,
the Option B85 and Option B1X kits also include a license for N9030B-B40.
Products Affected: N9030B PXA, Option 503, 508, 513, 526, 544, 550
Serial Numbers: All
To Be Performed By: (X) Keysight Service Center
(X) Personnel Qualified by Keysight
( ) Customer
Estimated Installation Time:
Estimated Adjustment Time:
Estimated Verification Time:
1.5 Hours
1.0 Hours
4.0 Hours
4Installation Note N9030-90075
Option B85 or B1X Retrofit Kit
The B85 or B1X option is licensed for only one instrument model number/ serial number
combination. The license file that is downloaded from the web will only install on the designated
instrument.
The instrument must be readjusted and the performance tested to assure the instrument meets
specifications following the hardware installation. The X-Series Performance Verification and
Adjustment Software must be used. All adjustments are automated. This software is included in
the N7814A, Keysight X-Series Signal Analyzer Calibration Application software.
Information on how to obtain this software can be found at:
www.keysight.com/find/calibrationsoftware
While Keysight does recommend that a full calibration be performed after the installation of this
upgrade, the end user must ultimately determine whether they want this service or not. If a full
calibration is required, arrangements regarding the level of calibration must be made between
the end user and calibration provider.
Installation Note N9030-90075 5
Option B85 or B1X Retrofit Kit
Installation Kit Parts List
Quantity Description Keysight Part Number
1 Installation Note This note
1 Option Upgrade Entitlement Certificate 5964-5178
1 Wideband Analog IF Assembly N9020-60044
1 Wideband Digital IF Assembly N9020-60311
1 Cable Assembly, Flat Flexible 80-Conductor 3-in-LG 8121-1854
14 Screw, M3 x 0.5, 6 mm, Flathead 0515-1946
1
1
1
1
1
Cable Kit, includes cables below:
Cable Assembly, Coaxial 650 mm-LG
(with color bands 901 and 101 attached)
Cable Assembly, Coaxial 120G
(with color bands 806 and 726 attached)
Cable Assembly, Coaxial 120G
(with color bands 718 and 301attached)
Cable Assembly, Coaxial 530 mm LG
(with color bands 102 and 15 attached)
Cable Assembly, Coaxial 530 mm LG
(with color bands 17 and 805 attached)
8121-1865
8121-0152
8121-0152
8121-1401
8121-1401
6Installation Note N9030-90075
Option B85 or B1X Retrofit Kit
Tools Required
— T-10 TORX Driver
— T-20 TORX Driver
— 5/16-inch torque wrench
— Keysight Calibration and Adjustment Software,
N7814A TME Calibration Application, version E.16.00 or later
— Test equipment and computer supported by the X- Series Performance Tests and Adjustment
Software
— PXA Signal Analyzer Service Guide. This manual is available for immediate download in PDF
format from: www.keysight.com/find/N9030B_service_guide
— Microsoft Windows based personnel computer with internet access and USB port
— USB storage device with > 2 GB free memory
Initial Instrument Functionality Check
Power on the instrument and allow the instrument to boot up. Run an alignment and display the
measurement screen. (The instrument will probably display a spectrum analyzer screen and you will
see the instrument sweeping.)
There should be no alignment failures. If there are failures, investigate and fix the problem before
continuing.
Before you disassemble the instrument, turn the power switch to Standby and unplug the
instrument. Failure to unplug the instrument can result in personal injury.
Electrostatic discharge (ESD) can damage or destroy electronic components. All work on
electronic assemblies should be performed at a static-safe workstation. Refer to the
documentation that pertains to your instrument for information about static-safe workstations
and ordering static-safe accessories.
Installation Note N9030-90075 7
Option B85 or B1X Retrofit Kit
Procedure
Licensing the New Option(s)
License Installation Procedure over USB
1. Locate the Option Upgrade Entitlement Certificate in the kit and follow the directions to
redeem the upgrade product listed.
2. After redeeming the upgrade product from the Certificate, you will receive an e-mails with an
attached License File. Locate a USB storage device. Perform a virus scan on this device before
use.
3. Locate a USB storage device. Perform a virus scan on this device before use.
4. Save the License File to the root directory of the USB Storage Device.
5. Connect the USB Storage Device to one of the analyzer’s USB ports. Connect a mouse to
another USB port. Windows will detect the new hardware and may display the configuration
menu shown in Figure 1. This menu may be configured according to your preferences.
Figure 1 USB Storage Device Configuration Menu
If the instrument is placed on its face during any of the following procedures, be sure to use a soft
surface or soft cloth to avoid damage to the front panel, keys, or input connector.
Make sure any adapters on the front panel are removed.
8Installation Note N9030-90075
Option B85 or B1X Retrofit Kit
6. The signal analyzer will automatically consume the License File. (This may take a few minutes)
When the License File is consumed the Keysight License Manager will display a “Successful
License Installation” message similar to the one shown in Figure 2. If the license file contains
multiple licenses, multiple “Successful License Installation” messages will appear. Wait until
all licenses have been consumed before removing the USB Storage Device.
Figure 2 Successful License Installation
Alternate Installation Procedure
The License File(s) can be manually installed over USB or LAN by placing the license file in the
following analyzer folder: C:\Program Files\Agilent\licensing
Verify the License Installation
1. Before the licenses will be recognized, the XSA application must be restarted. Press System
and Exit Program. An Exit Program dialog box will appear; tap OK to confirm the exit.
2. Double-tap on the LaunchXSA icon on the Windows desktop. Wait for the XSA application to
finish starting (the analyzer should be sweeping).
3. Press System, Show System
—N9030B-B85 Analysis bandwidth, 85 MHz (if N9030BU-B85 is
being installed)
—N9030B-B1X Analysis bandwidth, 140 MHz (if N9030BU-B1X or N9030BU-BU3 is
being installed)
—N9030B-B40 Analysis bandwidth, 40 MHz
—N9030B-DP4 Digital Processor, 4 GB capture memory
Installation Note N9030-90075 9
Option B85 or B1X Retrofit Kit
Analyzer Disassembly
1. Refer to the Assembly Replacement Procedures chapter in the N9030B Signal Analyzer
Service Guide
2. Perform the removal procedures shown below in the order listed
a. Instrument Outer Case
b. Top Brace (discard flathead screws with patch lock)
c. Right Side Chassis
10 Installation Note N9030-90075
Option B85 or B1X Retrofit Kit
Removing Cables
1. Refer to Figure 5. Remove wire cable hold down on right side of chassis to free gray coax
cables.
2. Remove cable ties from bundle of gray coax cables.
3. Refer to Figure 3 that shows the A3 Digital IF assembly located on the bottom side of the
instrument. Remove cable W47 connecting A3 Digital IF J17 to A16 Reference Assembly J726.
Note cable routing from Digital IF J17 through the opening in the side panel. This cable will not
be reused.
4. Remove cable W26 connecting A15 Front End Controller J901 to A3 Digital IF J15. Note cable
routing from Digital IF J15 through the attenuator brackets and switches. This cable will not be
reused.
Figure 3 A3 Digital IF Assembly Cables
Otros manuales para N9030B
8
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Instrumento de medición de Keysight Technologies
Keysight Technologies
Keysight Technologies P Series Manual de usuario
Keysight Technologies
Keysight Technologies B1505A Manual de usuario
Keysight Technologies
Keysight Technologies 16197A Manual de operación
Keysight Technologies
Keysight Technologies N9030B Manual de instalación y operación
Keysight Technologies
Keysight Technologies C Series Manual de usuario
Keysight Technologies
Keysight Technologies N1060A Manual de usuario
Keysight Technologies
Keysight Technologies N77 Series Manual de usuario
Keysight Technologies
Keysight Technologies B1507A Manual de usuario
Keysight Technologies
Keysight Technologies N5511A-K26 Manual de usuario
Keysight Technologies
Keysight Technologies UXA Manual de instalación y operación
Keysight Technologies
Keysight Technologies N4373E Manual de usuario
Keysight Technologies
Keysight Technologies B2900A Series Manual de usuario
Keysight Technologies
Keysight Technologies N9320A RF Manual de usuario
Keysight Technologies
Keysight Technologies U3810A Manual de usuario
Keysight Technologies
Keysight Technologies 34972A Manual de usuario
Keysight Technologies
Keysight Technologies X-Series Manual de usuario
Keysight Technologies
Keysight Technologies E5055A SSA-X Manual de usuario
Keysight Technologies
Keysight Technologies U5303A Guía del usuario
Keysight Technologies
Keysight Technologies N9020A Manual de instalación y operación
Keysight Technologies
Keysight Technologies X Series Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario