Keysight Technologies 8970B Manual de usuario

Keysight Technologies

8970B Noise Figure Meter

Security and

Memory Clearing

Notices

© Copyright 2018 Keysight Technologies, Inc.

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

08970-90006

Edition

Edition 1, November 2018

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

8970B Noise Figure Meter Security and Memory Clearing 3

8970B Noise Figure Meter Security and Memory Clearing

8970B Noise Figure Meter Security and Memory Clearing

Introduction

8970B memory clearing process requires removal of the processor battery for 15 minutes or longer.

Below are step-by-step instructions for removing this battery. Make sure you use proper ESD

pre-cautions.

Tools Required

— Torx T15 driver

— #2 Phillips screwdriver

Procedure

1. Unplug the 8970B from AC power.

2. Place the instrument upside-down on a flat surface.

3. Remove the bottom cover using Torx T15 driver and #2 Phillips screwdriver.

4. Lift the processor assembly by loosening the two screws and hinge the board away as shown

below:

Figure 1 Battery Location

4 8970B Noise Figure Meter Security and Memory Clearing

8970B Noise Figure Meter Security and Memory Clearing

5. Remove battery shown in the lower-left corner of the processor board. Lift the contact clip and

slide the battery out.

6. After 15 minutes, replace the battery with positive terminal out as shown on the clip.

7. Re-install the processor board and replace the instrument bottom cover.

8. Connect the AC power cord and turn on the instrument.

9. Instrument memory is cleared if error message E80 (lost battery) appears at turn-on.

10.It is NOT necessary to re-enter the ENR tables for noise sources at this point.

11.Connect a noise source to the BNC drive and the RF input (failure to do this will cause an E13

IF calibration failure message).

12.Invoke special function 33.1 to perform the I.F. calibration.

13.You may now calibrate the 8970B as desired for your next measurement.

Contacting Keysight

For assistance, contact your nearest Keysight Technologies Sales and Service Office. To find your

local Keysight office access the following URL, or if in the United States, call the following

telephone number:

http://www.keysight.com/find/assist

1-800-829-4444 (8 am - 8 pm ET, Monday - Friday)

This information is subject to change

without notice.

© Keysight Technologies 2018

Edition 1, November 2018

08970-90006

www.keysight.com

Tabla de contenidos

Otros manuales de Instrumento de medición de Keysight Technologies

Keysight Technologies

Keysight Technologies X Series Manual de instalación y operación

Keysight Technologies

Keysight Technologies N9000B Manual de instalación y operación

Keysight Technologies

Keysight Technologies M8131A Manual de usuario

Keysight Technologies

Keysight Technologies E4980A Manual de usuario

Keysight Technologies

Keysight Technologies 5061B Manual de usuario

Keysight Technologies

Keysight Technologies E5061B Manual de usuario

Keysight Technologies

Keysight Technologies 1130B Series Manual de usuario

Keysight Technologies

Keysight Technologies U1273A Manual de usuario

Keysight Technologies

Keysight Technologies N5244/5B Manual de usuario

Keysight Technologies

Keysight Technologies M9485A Guía del usuario

Keysight Technologies

Keysight Technologies PNA-L N5230A Manual de usuario

Keysight Technologies

Keysight Technologies 86120B Manual de usuario

Keysight Technologies

Keysight Technologies U4431A Manual de usuario

Keysight Technologies

Keysight Technologies N9010A Series Manual de instalación y operación

Keysight Technologies

Keysight Technologies U5303A Guía del usuario

Keysight Technologies

Keysight Technologies U5855A Manual de usuario

Keysight Technologies

Keysight Technologies B1500A Manual de instrucciones

Keysight Technologies

Keysight Technologies U2000 Series Manual de usuario

Keysight Technologies

Keysight Technologies N9020A Manual de instalación y operación

Keysight Technologies

Keysight Technologies E5072A Manual de usuario

Keysight Technologies

Keysight Technologies E5260 Series Manual de usuario

Keysight Technologies

Keysight Technologies N5251A Series Manual de usuario

Keysight Technologies

Keysight Technologies 6811C Instrucciones de funcionamiento

Keysight Technologies

Keysight Technologies N9029AV01-V15 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario