Kargo Master 406GM Manual
Instruction Guide
406GM
(partition shown for reference)
Kargo Master
Rancho Cordova, CA 95742
800-343-7486
CustomerService@KargoMaster.com
20190904R2
DATE: ______________
Instructions –406GM
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 2
*PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING,
INSTALLING, AND USING THIS PRODUCT*
Warning
Always check for wires, fuel tanks and lines, brake lines and other important vehicle
functionality items prior to drilling and installing all products.
Tools Needed
3/8” Wrench and Socket
7/16” Wrench and Socket
10mm Wrench and Socket
Table of Contents
Parts List ..........................................................................................................................................3
Hardware List ..................................................................................................................................4
Step 1 Attach Side Wings ................................................................................................................5
Step 2 Install Upper Mount to Partition ..................................................................................... 6-7
Step 3 Install Floor Mounts .............................................................................................................8
Step 4 Install Upper Corner Mounts ......................................................................................... 9-10
Step 5 Attach Upper Mount to Partition .......................................................................................11
Step 6 Attach Partition to Floor Mounts .......................................................................................12
Before You Begin
•Read all instructions.
•Be sure to have a partition assembled and ready to be installed.
Instructions –406GM
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 3
Parts
Instructions –406GM
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 4
Hardware
Instructions –406GM
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 5
Step 1 –Attach Side Wings
•Bolt both wings to the outer edges of
partition in the orientation shown using
1/4" x 5/8” flanged hex head bolts and
1/4” flanged nyloc nuts.
Note: The panel that has no holes, is the driver side of
the partition.
•Position each wing so that maximum seat
space is achieved when attaching to
partition.
•Repeat for a total of 8x.
•Snug tighten, but allow movement.
Driver Side
Passenger Side
Instructions –406GM
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 6
Step 2 –Install Upper Mount to Partition
•Place the upper mount against the partition assembly with the wing panels.
•Bolt the upper mount to the partition in the orientation shown using 1/4" x 1/2" carriage
bolt and 1/4" nyloc nut. The head of the carriage bolt goes on the cab side.
Note: If using the pass through door, leave the hardware out of the two door locations.
Instructions –406GM
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 7
•Snug tighten, but allow movement.
Views shown below are from the cab side of the van.
Instructions –406GM
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 8
Step 3 –Install Floor Mounts
•Behind both seats, locate the D-Rings in the floor.
•Remove both D-Rings.
•Align the floor mounts with the previously
removed D-Rings. Have the floor mounts oriented
to the rear of the van.
•Install the floor mounts using the previously
removed D-Rings as shown.
•Snug tighten, but allow movement.
Instructions –406GM
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 9
Step 4 –Install Upper Corner Mounts
•Along the roof of the van, locate the mount
locations behind both seats. These are
above the slider door.
•Evaluate the mounting locations and determine if a threaded emboss is present.
Note: In some vans, a M6 threaded emboss will be attached (see picture above). The others will have two through
holes.
•Be sure to use the correct upper corner mount. When the mount is attached properly, the
flange should be towards the front of the vehicle and parallel to the floor. The slots in the
upper corner mount will attach to the partition assembly.
•Through the rear most hole of the upper corner mount, attach in place using a M6 x 20mm
hex head bolt, two M6 flat washers and a M6 nyloc nut in the orientation shown.
•Repeat on both sides.
Instructions –406GM
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 10
•If there is no threaded emboss on the forward most hole location, install using a M6 x
20mm hex head bolt, two M6 flat washers and a M6 nyloc nut in the orientation shown.
•If a threaded emboss is present, attach through the front most hole location using a M6 x
20mm hex head bolt, M6 lock washer and M6 flat washer as shown.
•Repeat on opposite side of the van.
•Snug tighten, but allow movement.
M6 Emboss
M6 Emboss
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Kargo Master
Kargo Master
Kargo Master 4081P Manual de usuario
Kargo Master
Kargo Master 4A943 Manual de usuario
Kargo Master
Kargo Master 4A93L Manual de usuario
Kargo Master
Kargo Master 4A92L Manual de usuario
Kargo Master
Kargo Master PRO-II KS Manual de usuario
Kargo Master
Kargo Master 4095L Manual de usuario
Kargo Master
Kargo Master 48152 Manual de usuario
Kargo Master
Kargo Master 4832L Manual
Kargo Master
Kargo Master 4089P Manual
Kargo Master
Kargo Master 4A85L Manual
Kargo Master
Kargo Master 40816 Manual
Kargo Master
Kargo Master 80070 Manual
Kargo Master
Kargo Master 4A98L Manual
Kargo Master
Kargo Master 30070 Manual de usuario
Kargo Master
Kargo Master 409TD Manual de usuario
Kargo Master
Kargo Master 4A84L Manual
Kargo Master
Kargo Master 4A823 Manual
Kargo Master
Kargo Master 4A815 Manual de usuario
Kargo Master
Kargo Master 40813 Manual de usuario
Kargo Master
Kargo Master 40040 Manual
