Juniper ACX710 Manual de usuario
ACX710 Universal Metro Router Quick Start Guide
IN THIS GUIDE
ACX710 Description | 1
Step 1: Prepare the Site for ACX710 Installation | 2
Step 2: Install the ACX710 Chassis in the Rack | 5
Step 3: Connect the Grounding Cable | 7
Step 4: Connect to Power | 8
Step 5: Connect External Devices and Cables | 10
Step 6: Perform Initial Software Configuration | 12
Safety Warnings | 16
Compliance Statements for EMC Requirements | 18
Contacting Customer Support | 19
ACX710 Description
This Quick Start Guide contains information that you need to install and configure an ACX710 router quickly. For complete
installation instructions, see the ACX710 Universal Metro Router Hardware Guide at https://www.juniper.net/documentation/.
The ACX710 router provides an aggregation solution that is cost-effective and compact, and that supports emerging
deployments such as segment routing and Ethernet VPN (EVPN). The ACX710 includes support for numerous features
such as modern network management using NETCONF and YANG, and precise synchronization that helps address the
increasing demands of high-speed networks.
The ACX710 router is a 1-U compact and fixed-configuration model with high-density 1GbE, 10GbE, and 100GbE ports.
ACX710 routers provide full-duplex throughput of 320 Gbps and 24 Gbit DRAM packet buffer.
We ship these routers with a DC power supply module that has dual power feeds and a fan tray with five high-performance
fans that can effectively cool the chassis.
The port panel of the ACX710 router has the following port configurations:
•Twenty-four 10GbE or 1GbE ports (ports 0through 23) that operate at 10-Gbps speed when you use small form-factor
pluggable plus (SFP+) transceivers or at 1-Gbps speed when you use small form-factor pluggable (SFP) optics. Ports 0
through 15 also support 1000-Mbps speed when you use tri-rate SFP optics. Ports 16 through 23 support 100-Mbps
and 1000-Mbps speeds when you use tri-rate SFP optics.
•Four 100GbE ports (ports 0through 3) that support quad small form-factor pluggable 28 (QSFP28) transceivers. You
can channelize these ports into four 25-Gbps interfaces using breakout cables and channelization configuration. These
ports also support 40-Gbps speed when you use quad small form-factor pluggable plus (QSFP+) optics. You can channelize
these 40-Gbps ports into four 10-Gbps interfaces using breakout cables and channelization configuration.
Figure 1 shows the front panel of an ACX710 router.
Figure 1: ACX710 Router Front Panel
g100870
4 5
2 31 2
9 8
6 7
4—1—TOD (RJ-45), I/O(RJ-45), LMT (RJ-45), and BITS (RJ-48) portsPower supply unit
5—2—USB port1GbE/10GbE ports (24 SFP or SFP+ ports)
6—3—Console port40GbE/100GbE ports (4 QSFP+ or QSFP28 ports)
Figure 2 shows the rear view of an ACX710 router.
Figure 2: Rear View of the ACX710 Router
g100873
1
1—Fan tray
Step 1: Prepare the Site for ACX710 Installation
IN THIS SECTION
Rack Requirements for ACX710 Routers | 3
Router Clearance Requirements | 4
Router Cooling and Airflow Requirements | 4
Tools and Parts Required to Prepare the ACX710 Router for Installation | 5
2
Rack Requirements for ACX710 Routers
The ACX710 routers are designed to be installed on four-post racks.
Table 1 provides the rack requirements and specifications for ACX710 routers.
Table 1: Rack Requirements for ACX710 Routers
GuidelinesRack Requirement
Use a four-post rack that provides bracket holes or hole patterns spaced at 1-U increments
(1.75 in. or 4.45 cm), and ensure that the rack meets the size and strength requirements to
support the weight of the router.
A U is the standard rack unit defined in Cabinets, Racks, Panels, and Associated Equipment
(document number EIA-310–D) published by the Electronics Industry Association.
Rack type
Ensure that the holes in the mounting brackets are spaced at 1 U (1.75 in. or 4.45 cm) so that
the router can be mounted in any rack that provides holes spaced at that distance.
Mounting bracket
hole spacing
•Ensure that the rack complies with the standards for a 19-in. rack as defined in Cabinets,
Racks, Panels, and Associated Equipment (document number EIA-310–D) published by the
Electronics Industry Association.
•Use an 800-mm rack as defined in the four-part Equipment Engineering (EE) European
telecommunications standard for equipment practice (document numbers ETS 300 119-1
through 119-4) published by the European Telecommunications Standards Institute
(http://www.etsi.org).
The horizontal spacing between the rails in a rack that complies with this standard is usually
wider than the device's mounting brackets, which measure 19 in. (48.26 cm) from outer edge
to outer edge. Use approved wing devices to narrow the opening between the rails as
required.
•Ensure that the rack rails are spaced widely enough to accommodate the external dimensions
of the router chassis. The outer edges of the front-mounting brackets extend the width to
19 in. (48.26 cm).
•Ensure that for four-post installations, the front and rear rack rails are spaced between
23.6 in. (60 cm) and 36 in. (91.4 cm) front-to-back.
•Ensure that the rack is strong enough to support the weight of the router. A fully configured
ACX710 router weighs about 17.64 lb (8 kg).
•Ensure that the spacing of rails and adjacent racks allows for proper clearance around the
router and rack.
Rack size and
strength
•Secure the rack to the building structure.
•If earthquakes are a possibility in your geographical area, secure the rack to the floor.
•Secure the rack to the ceiling brackets and to the wall or floor brackets for maximum stability.
Rack connection to
building structure
3
Router Clearance Requirements
For the cooling system to function properly, the airflow around the chassis must be unrestricted. You must allow sufficient
clearance around the installed chassis for cooling and maintenance.
If you are mounting an ACX710 in a rack with other equipment, ensure that the exhaust from the other equipment does
not blow into the intake vents of the ACX710 chassis.
For service personnel to remove and install hardware components, and to accommodate the interface and power cable
bend radius, there must be adequate space at the front and rear of the router. Allow at least 24 in. (61 cm) of space both
at the front and rear of the router. See Figure 3 for the clearance requirements for ACX710 routers.
Figure 3: Clearance Requirements for Airflow and Hardware Maintenance for ACX710 Routers
g100881
Mounting bracket
Clearance required
for maintenance
12.4 in.
31.5 cm
Clearance required
for maintenance
Front
(Ports) Rear
19.0 in.
(48.26 cm)
17.36 in.
(44.08 cm)
24 in. (61 cm) 24 in. (61 cm)
Router Cooling and Airflow Requirements
•In ACX710 routers, cool air is pulled through the front of the chassis towards the rear fan tray, and hot air is exhausted
out of the chassis through the rear. Figure 4 shows the airflow through the ACX710 router.
•For the cooling system to function properly, the airflow around the chassis must be unrestricted.
•The rack or cabinet must have an adequate supply of cool air.
4
Figure 4: Airflow Through the ACX710 Chassis
Front Rear
g100883
Tools and Parts Required to Prepare the ACX710 Router for Installation
•19-in. four-post rack with fasteners (provided)
•ESD grounding strap (not provided).
•One pair of front-mounting rails (provided)
•Screws to secure the chassis to the rack (not provided).
•Appropriate screwdriver for the mounting screws (not provided).
•Two DC power cords with plugs appropriate for your geographical location (provided).
•One grounding cable (provided).
•RJ-45 cable and RJ-45 to DB-9 serial port adapter (not provided).
•Management host, such as a PC or laptop, with a serial port (not provided).
Step 2: Install the ACX710 Chassis in the Rack
To install the router in a four-post rack:
1. Position the router in front of the rack.
2. Wrap and fasten one end of the ESD grounding strap around your bare wrist, and connect the other end of the strap
to a site ESD point.
3. Align the holes in the front-mounting rails with the holes on the side of the chassis (see Figure 5).
5
Figure 5: Install the Mounting Rails on an ACX710 Router
g100886
4. Using a Phillips (+) number 2 screwdriver, secure the mounting rails to the chassis using the mounting screws.
5. With one person on each side, hold on to the bottom of the chassis, and carefully lift the chassis so that the mounting
rails are aligned with the rack rails.
6. Carefully slide the chassis with the rails attached on to the rack rails (see Figure 6).
Figure 6: Install the ACX710 Router in a Four-Post Rack
g100887
7. Install mounting screws into each of the front-mounting bracket holes aligned with the rack, starting from the bottom,
and tighten the screws.
8. Align the holes in the cable bar with the holes at the top of the mounting bracket, and tighten the screws to attach the
cable bar.
Figure 7: Install the Cable Bar
g100888
9. Visually inspect the alignment of the chassis.
6
If you’ve installed the chassis properly in the rack, all the mounting screws on one side of the rack are aligned with the
mounting screws on the opposite side, and the router is level. Figure 8 shows the router fully secured and installed in
a four-post rack.
Figure 8: ACX710 Router Installed in a Four-Post Rack
g100891
Step 3: Connect the Grounding Cable
To meet safety and electromagnetic interference (EMI) requirements and to ensure proper operation, the router must be
adequately grounded before power is connected.
You need a protective earthing terminal bracket for connecting the chassis to earth ground. This two-holed bracket is
attached on the side of the chassis through the mounting rail, and provides a protective earthing terminal for the router.
The grounding points are in the form of studs that are sized for M6 screws. (You need to provide these screws with
integrated washers as we do not ship them in the accessory kit).
To ground the ACX710 router:
1. Verify that a licensed electrician has attached the cable lug provided with the router to the grounding cable.
2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the other end of the strap to
an approved site ESD grounding point. See the instructions for your site.
3. Ensure that all grounding surfaces are clean and are brought to a bright finish before you make grounding connections.
4. Connect the grounding cable to a proper earth ground.
5. Place the grounding cable lug over the grounding points on the side of the chassis (see Figure 9).
7
Figure 9: Connect the Grounding Cable to the ACX710 Router
g100882
6. Secure the grounding cable lug with the screws.
7. Dress the grounding cable, and verify that it does not touch or block access to router components, and that it does
not drape where people could trip on it.
Step 4: Connect to Power
The ACX710 router supports a dual feed DC power supply module. Table 2 describes the DC power specifications for
ACX710 routers. For the 2-pole DC circuit breaker, the recommended maximum value is 32 A and the minimum value is
8 A.
Table 2: DC Power Specifications for ACX710 Routers
SpecificationsItem
-48 V DCNominal input voltage
-38 V DC to -60 V DCInput voltage range
6 AMaximum current
150 WTypical power consumption
225 WMaximum power consumption
Before you begin connecting DC power to the router:
•Ensure that you have taken the necessary precautions to prevent electrostatic discharge (ESD) damage (see Prevention
of Electrostatic Discharge Damage).
•Ensure that you have connected the router chassis to earth ground.
8
CAUTION: Before you connect power to the router, a licensed electrician must attach a cable lug
to the grounding and power cables that you supply. A cable with an incorrectly attached lug can
damage the router (for example, by causing a short circuit).
To meet safety and electromagnetic interference (EMI) requirements and to ensure proper operation,
you must connect the chassis to earth ground before you connect the chassis to power. For
installations that require a separate grounding conductor to the chassis, use the protective earthing
terminal on the router chassis to connect to the earth ground.
•Ensure that you have the following parts and tools available:
•DC power source cables
•Phillips (+) screwdriver, number 2 (not provided)
•Multimeter (not provided)
To connect DC power to an ACX710 router:
1. Wrap and fasten one end of the ESD grounding strap around your bare wrist, and connect the other end of the strap
to a site ESD point.
2. Power off the DC input appliance inlet on the source power supply.
3. Connect the power cord to the power source outlet.
4. Insert the power cord firmly into the inlet.
Figure 10: Connect a DC Power Cord to an ACX710 Router
g100878
5. Route the power cord appropriately. Verify that the power cord does not block the air exhaust or access to router
components, or drape where people could trip over it.
6. Power on the source power supply.
9
Step 5: Connect External Devices and Cables
IN THIS SECTION
Connect an ACX710 Router to a Network for Out-of-Band Management | 10
Connect an ACX710 Router to a Management Console | 11
All the connections to the router are made through the front panel.
Connect an ACX710 Router to a Network for Out-of-Band Management
You can monitor and manage an ACX710 router by using a dedicated management channel. Use the management port
(LMT) to connect the ACX710 router to a network for out-of-band management.
Ensure that you have an Ethernet cable that has an RJ-45 connector at either end. Figure 11 shows the RJ-45 connector
of the Ethernet cable.
Figure 11: RJ-45 Connector on an Ethernet Cable
NOTE: You cannot use the management ports to perform the initial configuration of an ACX710 router. You
must configure the management ports before you can successfully connect to the ACX710 router using these
ports. See Perform Initial Software Configuration for the ACX710 Routers.
Ensure that you have an appropriate cable available. See ACX710 Network Cable and Transceiver Planning.
To connect an ACX710 router to a network for out-of-band management (see Figure 12):
1. Connect one end of the Ethernet cable to one of the management ports.
2. Connect the other end of the cable to the management PC (see Figure 12).
10
Tabla de contenidos
Otros manuales de Enrutador de red de Juniper
Juniper
Juniper M20 Manual de usuario
Juniper
Juniper T320 Instrucciones de instalación
Juniper
Juniper EX4500 Series Instrucciones de instalación
Juniper
Juniper MX240 Manual de usuario
Juniper
Juniper PTX1000 Instrucciones de instalación
Juniper
Juniper MX2010 Instrucciones de instalación
Juniper
Juniper PTX3000 Hoja de especificaciones
Juniper
Juniper JUNOS OS 10.4 Manual de usuario
Juniper
Juniper MX240 Instrucciones de instalación
Juniper
Juniper MX10004 Manual de usuario
Juniper
Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX HARDWARE GUIDE REV... Instrucciones de instalación
Juniper
Juniper ACX4000 Manual de usuario
Juniper
Juniper PTX10001 Manual de usuario
Juniper
Juniper PTX10008 Instrucciones de instalación
Juniper
Juniper ACX5096 Manual de usuario
Juniper
Juniper SSR1200 Instrucciones de instalación
Juniper
Juniper QFX10002 Manual de usuario
Juniper
Juniper E120 - RELEASE 11.1.X HARDWARE GUIDE... Instrucciones de instalación
Juniper
Juniper T1600 Instrucciones de instalación
Juniper
Juniper E320 Manual de usuario
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad