Juniper PTX10004 Manual de usuario

PTX10004

Published

2023-09-12

RELEASE

Table of Contents

Step 1: Begin

Meet the PTX10004 | 1

Install the PTX10004 in a Rack | 1

What’s in the Crate? | 2

What Else Do I Need? | 2

Assemble the Rack Mount Kit | 2

Mount the PTX10004 on a the Rack and Ground the Chassis | 3

Power On | 5

Step 2: Up and Running

Connect to the Router | 7

Set a Root Password and an Oponal Hostname | 8

Congure the Default Gateway and Ethernet Interface | 9

Congure Oponal Routes, Services, and Commit the Conguraon | 9

Step 3: Keep Going

What’s Next? | 11

General Informaon | 11

Learn With Videos | 12

Step 1: Begin

IN THIS SECTION

Meet the PTX10004 | 1

Install the PTX10004 in a Rack | 1

Power On | 5

In this guide, we provide a simple, three-step path, to quickly get you up and running with your new AC-

powered router. We've simplied and shortened the installaon and conguraon steps, and included

how-to videos. You'll learn how to install the PTX10004 in a rack, power it up, and congure basic

sengs.

Meet the PTX10004

The Juniper Networks® PTX10004 modular router is the ultra-compact, ultra-high-density router for

today’s space-and power-constrained facilies. The PTX10004 supports 400GbE architectures with

inline Media Access Control Security (MACsec) on all ports for uncompromised security. The compact 7-

U design and the ability to scale from 19.2 Tbps to 57.6 Tbps makes the PTX10004 perfectly opmized

for data center and colocaon racks.

Install the PTX10004 in a Rack

IN THIS SECTION

What’s in the Crate? | 2

What Else Do I Need? | 2

Assemble the Rack Mount Kit | 2

Mount the PTX10004 on a the Rack and Ground the Chassis | 3

Before you begin the installaon, review General Safety Guidelines and Warnings.

What’s in the Crate?

Along with your PTX10004, you’ll also nd:

• A rack mount kit with:

• Twelve Phillips 8-32 x .375 in. at-head screws

• Two rear rails

• A mounng tray

• A rear safety restraint

• The front door kit

• An accessory kit with:

• RJ-45 Ethernet cable

• RJ-45 to DB9 rollover cable

•Electrostac discharge (ESD) wrist strap with cable

• Media kit (ash drives, PCMCIA card adapter)

• Ground chassis lug, 2-hole, 10-32, 4 AWG

• Power cord retainer clips, two for each power supply

What Else Do I Need?

• A mechanical li rated for 250 lb (113.4 kg). You can mount a PTX10004 manually or by using a

mechanical li. Because of the router's size and weight, we strongly recommend that you use a

mechanical li to mount the PTX10004. In this guide, we show you how to mount the router using a

mechanical li.

• 4 AWG (21.1 mm²) stranded wire grounding cable rated 75° C or per local electrical code

• A Phillips (+) screwdriver, number 2 or number 3, depending on the size of your rack mount screws

• A number 3 Pozidriv or Phillips (+) screwdriver for the grounding screws

• Twenty eight rack mount screws appropriate for your rack to secure the mounng blades, mounng

tray, chassis, and safety restraint to the rack

Assemble the Rack Mount Kit

1. Aach the mounng blades to the front rack posts using six rack mount screws.

2. From the rear of the rack, slide the mounng tray into the rear posts of the rack such that the

mounng blades align below the anges on either sides of the mounng tray.

3. Aach the tray to the rear rack posts using eight rack mount screws.

4. Aach the tray to the mounng blades in the rack using the 12 at-head screws.

Mount the PTX10004 on a the Rack and Ground the Chassis

1. Wrap and fasten one end of the electrostac discharge (ESD) grounding strap around your bare

wrist, and connect the other end to a site ESD point.

2. Load the router onto the li, making sure it rests securely on the li plaorm.

3. Align the router in front of the rack, centering it in front of the mounng tray.

4. Li the chassis approximately 0.75 in. (1.9 cm) above the surface of the mounng tray. Align the

chassis as close as possible to the mounng tray.

5. Carefully slide the chassis onto the shelf unl the chassis anges contact the rack rails.

6. Starng at the boom, aach the chassis to the rack by inserng eight rack mount screws through

each open ange hole and rack hole.

7. Move the li away from the rack.

8. Check the alignment of the router. The rack mount screws on each side of the rack should line up,

and the router should be level. Tighten the screws.

9. Insert the safety restraint between the rear posts of the rack. It should rest on the top of the

chassis and align with the holes in the rack.

10. Aach the restraint to the rack by inserng six mounng screws through each ange hole and rack

hole and ghtening the screws.

11. Install the line cards:

a. Remove the line card cover by grasping the handles and pulling straight out to expose the slot

for the line card. Save the cover.

b. Slide the line card all the way into the slot unl the handle holes line up.

c. Rotate the handles simultaneously into the chassis unl the card is fully seated and the handles

are vercal.

12. Install the opcs and oponal cable management system.

13. Li the front door and line up the capve screws in the door with the holes in the chassis ange.

Aach the door to the chassis and rack using the capve screws. Turn the screws unl they are

nger ght.

14. Have a licensed electrician aach the cable lug (provided in the accessory kit) to the grounding

cable.

15. Remove the two M6 screws with aached washers below the boom power supply using a

Pozidriv or Phillips screwdriver.

16. Place the chassis grounding lug and cable over the screw holes with the cable connecon poinng

to the le. Place the two screws with aached washers over the grounding lug and grounding

cable. Tighten the two M6 screws using a Pozidriv or Phillips screwdriver.

Power On

Now that you’ve installed your PTX10004 in the rack and grounded the chassis, you’re ready to connect

it to power.

The PTX10004 supports AC, DC, high-voltage alternang current (HVAC), and high-voltage direct

current (HVDC). In this guide, we show you how to connect AC power. See the PTX10004 hardware

guide for informaon on other power opons.

1. Wrap and fasten one end of the electrostac discharge (ESD) grounding strap around your bare wrist,

and connect the other end to a site ESD point.

2. If the AC power source outlet has a power switch, turn it o.

NOTE: If you need power source redundancy, you can aach each power cable to separate

power sources.

3. Turn o the power switch on the power supply.

4. Aach each power supply to a dedicated power source.

5. Set the three DIP switches on the power supply to indicate whether one or both power feeds are

used, and to indicate the amperage of the feeds. Together, these switches determine if the chassis

operates at 3,000 W, 5,000 W, or 5,500 W.

If you're using both power feeds, set switch 1 and switch 2 to the on (|) posion. Power is shared. If

you’re not using power source redundancy, set the unused source to the o (O) posion. The LED

turns red and indicates an error if a power source input is not in use and the DIP switch is on (|).

Switch State Descripon

1 On INP0 is present.

O INP0 is not present.

2 On INP1 is present.

O INP1 is not present.

3 On Enabled for 30-A feed; 5,000 W for single feed, 5,500 W for dual feeds.

O Enabled for 20-A feed; power supply capacity is 3,000 W.

6. Plug the AC power cord into the power outlet.

7. If the AC power source outlet has a power switch, turn it on.

8. Turn on the power switch on the power supply.

9. If you’re using two power feeds, verify that the 1 and 2 LEDs on the power supply faceplates are

steadily lit. These LEDs correspond to INP0 and INP1.

Step 2: Up and Running

IN THIS SECTION

Connect to the Router | 7

Set a Root Password and an Oponal Hostname | 8

Congure the Default Gateway and Ethernet Interface | 9

Congure Oponal Routes, Services, and Commit the Conguraon | 9

Now that the PTX10004 is powered on, let’s do some inial conguraon to get the router up and

running on the network. It’s simple to provision and manage the PTX10004 on your network.

The PTX10004 supports zero-touch provisioning (ZTP) which autoinstalls a soware image and device-

specic conguraon le when you connect the PTX10004 and other devices on your network. To use

ZTP, you’ll need to congure sengs on a DHCP server. For more informaon, see Zero Touch

Provisioning Using DHCP Opons.

Connect to the Router

1. Connect the console port to a laptop or PC using the supplied RJ-45 cable and RJ-45 to DB-9

adapter. The console (CONSOLE) port is located on the Roung and Control Board (RCB).

2. Verify that your laptop or PC has the following default values:

• Baud Rate—9600

• Flow Control—None

• Data—8

• Parity—None

• Stop Bits—1

• DCD State—Disregard

3. Have the following informaon ready before you start to congure the PTX10004:

• The password you’ll set for the root user

• The name on the system that the PTX10004 will be known as (hostname)

• The IP address and prex of the default gateway router

• The IP address and prex length informaon for the management Ethernet interface

• The IP address and prex length of remote prexes

4. Log in as root. There is no password. If the soware boots before you connect to the console port,

you might need to press the Enter key for the prompt to appear.

Amnesiac <ttyd0>

5. Start the CLI.

root@% cli

Set a Root Password and an Oponal Hostname

1. Add a password to the root administraon user account.

[edit]

root@# set system root-authentication plain-text-password

New password:

password

Retype new password:

password

2. (Oponal) Congure the name of the router. If the name includes spaces, enclose the name in

quotaon marks (“ ”).

[edit]

root@# set system host-name

host-name

3. (Oponal) Create a user account.

[edit]

root# set system login user

user-name

authentication plain-text-password

New password:

password

Retype new password:

password

4. (Oponal) Set the user account class to super-user.

[edit]

root# set system login user

user-name

class super-user

Otros manuales para PTX10004

Tabla de contenidos

Otros manuales de Enrutador de red de Juniper

Juniper

Juniper MX5 Manual de usuario

Juniper

Juniper JCS 1200 Manual de usuario

Juniper

Juniper PTX10008 Instrucciones de instalación

Juniper

Juniper PTX Series Manual de usuario

Juniper

Juniper MX960 Instrucciones de instalación

Juniper

Juniper M320 Instrucciones de instalación

Juniper

Juniper ACX2000 Instrucciones de instalación

Juniper

Juniper QFX10002 Manual de usuario

Juniper

Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV... Manual de usuario

Juniper

Juniper PTX10001-36MR Manual de usuario

Juniper

Juniper MX150 Instrucciones de instalación

Juniper

Juniper MX2010 Instrucciones de instalación

Juniper

Juniper ACX1100 Manual de usuario

Juniper

Juniper E320 Manual de usuario

Juniper

Juniper EX4600 Manual de usuario

Juniper

Juniper MX10003 Instrucciones de instalación

Juniper

Juniper Day One+ ACX7509 Manual de usuario

Juniper

Juniper M120 Instrucciones de instalación

Juniper

Juniper ACX6160 Instrucciones de instalación

Juniper

Juniper MX5 Instrucciones de instalación

Juniper

Juniper Juniper Networks Instrucciones de instalación

Juniper

Juniper E SERIES BROADBAND SERVICES ROUTERS - E SERIES END-OF-LIFE MODULE GUIDE... Manual de usuario

Juniper

Juniper MX Series Manual de usuario

Juniper

Juniper ERX - RELEASE 11.1.X HARDWARE GUIDE... Instrucciones de instalación

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad