jbc CD-F Manual de usuario
Blue Screen Soldering Stations
Model references: CD-F, CA-F, CP-F, CSV-F
Error num.
Displayed message
Solution
1
WARNING #1
Short circuit. Check the tool. Replace the
cartridge and/or the tool. If the problem
persists, contact the JBC Technical Service
via service@jbctools.com.
Replace the cartridge and/or the tool.
2
WARNING #2
Open circuit. Check the tool. Replace the
cartridge and/or the tool. If the problem
persists, contact the JBC Technical Service
via service@jbctools.com.
3
WARNING #3
Not accepted tool. Replace the tool. Make
sure it is compatible with the station. If the
problem persists, contact the JBC Technical
Service via service@jbctools.com.
Replace the tool.
Make sure it is compatible with the station.
10
WARNING #10
Current use is overloading the unit.
Continued use will cause the system to stop.
Unit is overheated
Switch off and wait to cool down before new operation.
Consider working with a more powerful equipment as HDE Heavy Duty station.
STOP #10
Station overheated. Switch off and wait until
it has cooled down before a new operation.
Consider to use HDE Station if this warning
appears frequently
11
STOP #11
Transformer temperature sensor error.
Restart the station. If the problem persists,
contact the JBC Technical Service via
service@jbctools.com.
Restart the station.
12
STOP #12
Memory error. Restart the station. If the
problem persists, contact the JBC Technical
Service via service@jbctools.com.
13
STOP #13
Mains frequency error. Reset the station
after connecting the proper power supply. If
the problem persists, contact the JBC
Technical Service via service@jbctools.com.
Make sure the station is connected to a 50/60 Hz power source without
interference and restart the station.
16
WARNING #16
Earthing fuse is blown. Replace the
damaged fuse by a new one. You can press
"OK" to continue working, but be aware that
tip to ground resistance would not meet the
specifications in that case.
Replace the blown earth fuse for a new one.
If problem not solved, contact us:
www.jbctools.com
0024484 - 0522
Model references: CD, CF, CA, CP, CS, CV, DM, DD, DDR, NA, HD, HDR, DI, WS
Error num.
Displayed message
Solution
1
WARNING #1
Port X/Y
Shortcircuit. Check the tool.
Replace the cartridge and/or the tool.
2
WARNING #2
Port X/Y
Open circuit. Check the tool.
3
WARNING #3
No accepted tool.
Replace the tool.
Make sure it is compatible with the station.
4
WARNING #4
Port X/Y
Tool detection error. Check the tool.
6
in HD station
STOP #6
Port X/Y
Due to overload wait for unit to cool.
Unit is overheated.
Switch off and wait to cool down before new operation.
6
in other
stations
STOP #6
Port X/Y
Due to overload wait for unit to cool, JBC
recommends HD station to get more power.
Unit is overheated.
Switch off and wait to cool down before new operation.
JBC recommends to use HD station for these high power requirements.
7
in HD station
WARNING #7
Port 1/1
Shortcircuit. Check the tool.
Reset station and try new cartridge or tool.
Make sure they are compatible with the HD station.
10
in HD station
WARNING #10
Current use overloading unit. Continued use
will cause system to stop.
Unit is overheated
Switch off and wait to cool down before new operation.
STOP #10
Due to overload wait for unit to cool.
10
in other
stations
WARNING #10
Current use overloading unit. Continued use
will cause system to stop.
Unit is overheated
Switch off and wait to cool down before new operation.
Consider working with a more powerful equipment as HDE Heavy Duty station.
STOP #10
Due to overload wait for unit to cool, JBC
recommends HD station to get more power.
11
STOP #11
Error sensor temperature transformer.
Contact with the technical service.
Restart the station.
12
STOP #12
Memory error. Contact with the technical
service.
13
STOP #13
Mains frequency error. Contact with the
technical service.
Make sure the station is connected to a 50/60 Hz power source without
interference and restart the station.
If problem not solved, contact us:
www.jbctools.com
0024484 - 0522
Este manual sirve para los siguientes modelos
3
Otros manuales de Pistola de soldar de jbc
jbc
jbc RBA-A Manual de usuario
jbc
jbc CS-E Series Manual de usuario
jbc
jbc WSST Manual de usuario
jbc
jbc B-IRON 500 Manual de usuario
jbc
jbc PHNE-K Manual de usuario
jbc
jbc CDES Manual de usuario
jbc
jbc CA-QF Manual de usuario
jbc
jbc CDEB Manual de usuario
jbc
jbc AD 2940 Manual de usuario
jbc
jbc Advanced Series Manual de usuario
jbc
jbc CD-B Manual de usuario
jbc
jbc CD-2BHE Manual de usuario
jbc
jbc CD-BD Manual de usuario
jbc
jbc IN 2100 Manual de usuario
jbc
jbc CD Manual de usuario
jbc
jbc CL9885 Manual de usuario
jbc
jbc CD-Be Manual de usuario
jbc
jbc RWB-A Manual de usuario
jbc
jbc SF280 Manual de usuario
jbc
jbc CP-2E Manual de usuario
Manuales populares de Pistola de soldar de otras marcas
Vishay Precision Group
Vishay Precision Group Micro-Measurements Mark V Instrucciones de montaje
ersa
ersa i-CON 1V Manual de usuario
Hakko Electronics
Hakko Electronics FX-100 Manual de usuario
Weller
Weller WAD 101 Manual de usuario
Weller
Weller WXD 2 Manual de usuario
AlienTek
AlienTek T100 Manual de usuario
